- 23 10月, 2010 40 次提交
-
-
由 Igor Grinberg 提交于
Extend id's table to have ulpi phy names in it. Report if the known phy is found. Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Igor Grinberg 提交于
Improve ulpi phy detection by utilizing the "scratch" register. Allow unknown ulpi phy work without the need to hard-code the id. Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alon Ziv 提交于
Signed-off-by: NAlon Ziv <alon-git@nolaviz.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alon Ziv 提交于
OPN2001 expects write operations to arrive as a vendor-specific command through the control pipe (instead of using a separate bulk-out pipe). Signed-off-by: NAlon Ziv <alon-git@nolaviz.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alon Ziv 提交于
The bulk-read callback had two bugs: a) The bulk-in packet's leading two zeros were returned (and the two last bytes truncated) b) The wrong URB was transmitted for the second (and later) read requests, causing further reads to return the entire packet (including leading zeros) Signed-off-by: NAlon Ziv <alon-git@nolaviz.org> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
No need to set latency timeout at every open. This also fixes an issue with the read latency being as high as 250ms (instead of 1ms) for the first read after port probe. Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Kees Cook 提交于
If the iowarrior devices in this case statement support more than 8 bytes per report, it is possible to write past the end of a kernel heap allocation. This will probably never be possible, but change the allocation to be more defensive anyway. Signed-off-by: NKees Cook <kees.cook@canonical.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Johan Hovold 提交于
Fix regression introduced by commit 214916f2 (USB: visor: reimplement using generic framework) which broke initialisation of UX50/TH55 devices that used re-mapped bulk-out endpoint addresses. Reported-by: NRobert Gadsdon <rgadsdon@bayarea.net> Tested-by: NRobert Gadsdon <rgadsdon@bayarea.net> Cc: stable <stable@kernel.org> Signed-off-by: NJohan Hovold <jhovold@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Daniel Suchy 提交于
This patch for FTDI USB serial driver ads new VID/PIDs used on various devices manufactured by Papouch (http://www.papouch.com). These devices have their own VID/PID, although they're using standard FTDI chip. In ftdi_sio.c, I also made small cleanup to have declarations for all Papouch devices together. Signed-off-by: NDaniel Suchy <danny@danysek.cz> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Tatyana Brokhman 提交于
Adding SuperSpeed usb definitions as defined by ch9 of the USB3.0 spec. This patch is a preparation for adding SuperSpeed support to the gadget framework. Signed-off-by: NTatyana Brokhman <tlinder@codeaurora.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Michal Nazarewicz 提交于
This commit changes storage_common.h, file_storage.c and f_mass_storage.c to use definitions of SCSI commands from scsi/scsi.h file instead of redefining the commands in storage_common.c. scsi/scsi.h header file was missing READ_FORMAT_CAPACITIES and READ_HEADER so this commit also add those to the header. Signed-off-by: NMichal Nazarewicz <mina86@mina86.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: James Bottomley <James.Bottomley@suse.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 matt mooney 提交于
For all modules, change <module>-objs to <module>-y; remove if-statements and replace with lists using the kbuild idiom; move flags to the top of the file; and fix alignment while trying to maintain the original scheme in each file. None of the dependencies are modified. Signed-off-by: Nmatt mooney <mfm@muteddisk.com> Acked-by: NSam Ravnborg <sam@ravnborg.org> Acked-by: NFelipe Balbi <balbi@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Rahul Ruikar 提交于
In function dummy_udc_probe() call put_device() when device_register() fails. also usb_get_hcd() put before device_register() after review comment from Alan Stern. Signed-off-by: NRahul Ruikar <rahul.ruikar@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Rahul Ruikar 提交于
In function usb_create_ep_devs() call put_device() when device_register() fails. Signed-off-by: NRahul Ruikar <rahul.ruikar@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Anders Larsen 提交于
The WAGO 750-923 USB Service Cable is used for configuration and firmware updates of several industrial automation products from WAGO Kontakttechnik GmbH. Bus 004 Device 002: ID 1be3:07a6 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x1be3 idProduct 0x07a6 bcdDevice 1.00 iManufacturer 1 Silicon Labs iProduct 2 WAGO USB Service Cable iSerial 3 1277796751 . . . Signed-off-by: NAnders Larsen <al@alarsen.net> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Peter Chen 提交于
At otg device mode, the otg host resume should do no-op during system resume, otherwise, the otg device will be treated as a host for enumeration. So, the otg host driver returns -ESHUTDOWN if it detects the current usb mode is device mode. The host driver has to return -ESHUTDOWN, otherwise, the usb_hc_died will be called. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Hans de Goede 提交于
Some Rockbox based mp4 players will crash when ever they see a read_capacity_16 scsi command. So add a new US_FL which tells the scsi sd driver to not issue any read_capacity_16 scsi commands. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Hans de Goede 提交于
I seem to have a knack for digging up buggy usb devices which don't work with Linux, and I'm crazy enough to try to make them work. So this time a friend of mine asked me to get an mp4 player (an mp3 player which can play videos on a small screen) to work with Linux. It is based on the well known rockbox chipset for which we already have an unusual devs entries to work around some of its bugs. But this model comes with an additional twist. This model chokes on read_capacity_16 calls. Now normally we don't make those calls, but this model comes with an sdcard slot and when there is no card in there (and shipped from the factory there is none), it reports a size of 0. However this time the programmers actually got the read_capacity_10 response right! So they substract one from the size as stored internally in the mp3 player before reporting it back, resulting in an answer of ... 0xffffffff sectors, causing sd.c to try a read_capacity_16, on which the device crashes. This patch adds a flag to scsi_device to indicate that a a device cannot handle read_capacity_16, and when this flag is set if a device reports an lba of 0xffffffff as answer to a read_capacity_10, assumes it tries to report a size of 0. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Hans de Goede 提交于
Appotech ax3003 (the larger brother of the ax203) based devices are even more buggy then the ax203. They will go of into lala land when ever they see a READ_DISC_INFO scsi command. So add a new US_FL which tells the scsi sr driver to not issue any READ_DISC_INFO scsi commands. [akpm@linux-foundation.org: fix build] Signed-off-by: NHans de Goede <hdegoede@redhat.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Hans de Goede 提交于
Some USB devices emulate a usb-mass-storage attached (scsi) cdrom device, usually this fake cdrom contains the windows software for the device. While working on supporting Appotech ax3003 based photoframes, which do this I discovered that they will go of into lala land when ever they see a READ_DISC_INFO scsi command. Thus this patch adds a scsi_device flag (which can then be set by the usb-storage driver through an unsual-devs entry), to indicate this, and makes the sr driver honor this flag. I know this sucks, but as discussed on linux-scsi list there is no other way to make this device work properly. Looking at usb traces made under windows, windows never sends a READ_DISC_INFO during normal interactions with a usb cdrom device. So as this cdrom emulation thingie becomes more common we might see more of this problem. Signed-off-by: NHans de Goede <hdegoede@redhat.com> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Dan Carpenter 提交于
This is based on an initial patch by Rahul Ruikar. The goku_remove() function can be called before device_register() so it can call device_unregister() improperly. Also if the call to device_register() fails we need to call put_device(). As I was changing the error handling in goku_probe(), I noticed that the label was "done" but actually if the function succeeds we return earlier. I renamed the error path to "err" instead of "done." Reported-by: NRahul Ruikar <rahul.ruikar@gmail.com> Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Martin Fuzzey 提交于
The hardware can only do DMA to 4 byte aligned addresses. When this requirement is not met use PIO or a bounce buffer. PIO is used when the buffer is small enough to directly use the hardware data memory (2*maxpacket). A bounce buffer is used for larger transfers. Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Martin Fuzzey 提交于
Split unmap_urb_for_dma() to allow just the setup buffer to be unmapped. This allows HCDs to use PIO for the setup buffer if it is not suitable for DMA. Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Martin Fuzzey 提交于
Release the hardware resources and reset the internal HCD state associated with an isochronous endpoint when the last URB queued for it completes. Previously this was only done in then endpoint_disable() method causing usbtest 15 and 16 to hang when run twice in succession without a disconnect. Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Martin Fuzzey 提交于
We already have fields describing the hardware data memory (dmem_size and dmem_offset) in the HCD private data, use them rather than the rather obscure read from the hardware descriptor. Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Martin Fuzzey 提交于
Remove a local variable left over from some debugging code. Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Martin Fuzzey 提交于
Check the data length of isochronous transfers is as expected. With this test #16 will now fail if the device side sends no data. Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Martin Fuzzey 提交于
Signed-off-by: NMartin Fuzzey <mfuzzey@gmail.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1430) fixes a bug in usbcore. When a device configuration change occurs or a device is removed, the endpoints for the old config should be completely disabled. However it turns out they aren't; this is because usb_unbind_interface() calls usb_enable_interface() or usb_set_interface() to put interfaces back in altsetting 0, which re-enables the interfaces' endpoints. As a result, when a device goes through a config change or is unconfigured, the ep_in[] and ep_out[] arrays may be left holding old pointers to usb_host_endpoint structures. If the device is deauthorized these structures get freed, and the stale pointers cause errors when the the device is eventually unplugged. The solution is to disable the endpoints after unbinding the interfaces instead of before. This isn't as large a change as it sounds, since usb_unbind_interface() disables all the interface's endpoints anyway before calling the driver's disconnect routine, unless the driver claims to support "soft" unbind. This fixes Bugzilla #19192. Thanks to "Tom" Lei Ming for diagnosing the underlying cause of the problem. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Tested-by: NCarsten Sommer <carsten_sommer@ymail.com> CC: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Philippe Skowronski 提交于
It is safer to cancel pending requests before free dTD and dQH when controller enters suspend state. Signed-off-by: NPhilippe Skowronski <philippe.skowronski@intel.com> Signed-off-by: NHao Wu <hao.wu@intel.com> [Switch to spin_lock_irq as suggested by Alan Stern] Signed-off-by: NAlan Cox <alan@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Christophe Lebouc 提交于
This patch fixing the problem with large file transfers failing. Swap the read order to avoid unexpected RX status. Signed-off-by: NChristophe Lebouc <christophex.lebouc@intel.com> Signed-off-by: NHao Wu <hao.wu@intel.com> Signed-off-by: NAlan Cox <alan@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Ming Lei 提交于
This patch adds native scatter-gather support to uhci-hcd. Reviewed-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NMing Lei <tom.leiming@gmail.com> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
Blackfin's musb_platform_init() needs to call gpio_free() for error cleanup iff otg_get_transceiver() call returns NULL. Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NFelipe Balbi <balbi@ti.com> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
Blackfin's musb_platform_exit() forgets to call usb_nop_xceiv_unregister(). While fixing this, also remove the unneeded blank line there. Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: NMike Frysinger <vapier@gentoo.org> Cc: stable <stable@kernel.org> Signed-off-by: NFelipe Balbi <balbi@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
Since commit 461972d8 (musb_core: don't call musb_platform_exit() twice), unloading the driver module results in a WARNING "kobject: '(null)' (c73de788): is not initialized, yet kobject_put() is being called." (or even kernel oops) on e.g. DaVincis, though only in the OTG mode. There exists dubious and unbalanced put_device() call in musb_free() which takes place only in the OTG mode. As this commit caused musb_platform_exit() to be called (and so unregister the NOP transceiver) before this put_device() call, this function references already freed memory. On the other hand, all the glue layers miss the otg_put_transceiver() call, complementary to the otg_get_transceiver() call that they do. So, I think the solution is to get rid of the strange put_device() call, and instead call otg_put_transceiver() in the glue layers... Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Cc: stable <stable@kernel.org> Signed-off-by: NFelipe Balbi <balbi@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Anatolij Gustschin 提交于
Extends FSL EHCI platform driver glue layer to support MPC5121 USB controllers. MPC5121 Rev 2.0 silicon EHCI registers are in big endian format. The appropriate flags are set using the information in the platform data structure. MPC83xx system interface registers are not available on MPC512x, so the access to these registers is isolated in MPC512x case. Furthermore the USB controller clocks must be enabled before 512x register accesses which is done by providing platform specific init callback. The MPC512x internal USB PHY doesn't provide supply voltage. For boards using different power switches allow specifying DRVVBUS and PWR_FAULT signal polarity of the MPC5121 internal PHY using "fsl,invert-drvvbus" and "fsl,invert-pwr-fault" properties in the device tree USB nodes. Adds documentation for this new device tree bindings. Signed-off-by: NAnatolij Gustschin <agust@denx.de> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Anatolij Gustschin 提交于
Replace FSL USB platform code by simple platform driver for creation of FSL USB platform devices. The driver creates platform devices based on the information from USB nodes in the flat device tree. This is the replacement for old arch fsl_soc usb code removed by this patch. The driver uses usual of-style binding, available EHCI-HCD and UDC drivers can be bound to the created devices. The new of-style driver additionaly instantiates USB OTG platform device, as the appropriate USB OTG driver will be added soon. Signed-off-by: NAnatolij Gustschin <agust@denx.de> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: Grant Likely <grant.likely@secretlab.ca> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Rainer Keller 提交于
The OpenDCC project is developing a new hardware. This patch adds its PID to the list of known FTDI devices. The PID can be found at http://www.opendcc.de/elektronik/usb/opendcc_usb.htmlSigned-off-by: NRainer Keller <mail@rainerkeller.de> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Grazvydas Ignotas 提交于
Add empty functions for get/put transceiver functions too, so that drivers that optionally use them can call them without worrying that they might not exist, eliminating ifdefs. Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com> Acked-by: NFelipe Balbi <balbi@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Otavio Salvador 提交于
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-