This was introduced more than a decade ago when sg chaining was
added, but we never really caught anything with it. The scatterlist
entry size can be critical, since drivers allocate it, so remove
the magic member. Recently it's been triggering allocation stalls
and failures in NVMe.
Tested-by: NJordan Glover <Golden_Miller83@protonmail.ch>
Acked-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Fix the test that verifies whether bio_op(bio) represents a discard
or write zeroes operation. Compile-tested only.

Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Fixes: 7435e901 ("drbd: zero-out partial unaligned discards on local backend")
Signed-off-by: NBart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

It seems that during the conversion from gpio* to gpiod*, the initial
state of SCL was wrongly switched to LOW. Fix it to be HIGH again.

Fixes: 7bb75029 ("i2c: gpio: Enforce open drain through gpiolib")
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

If DMA safe memory was allocated, but the subsequent I2C transfer
fails the memory is leaked. Plug this leak.

Fixes: 8a77821e ("i2c: smbus: use DMA safe buffers for emulated SMBus transactions")
Signed-off-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

So, if somebody wants to re-implement this in the future, we pinpoint to
a problem case.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

This reverts commit 3e5f06be. As per
bugzilla #200045, this caused a regression. I don't really see a way to
fix it without having the hardware. So, revert the patch and I will fix
the issue I was seeing originally in the i2c-gpio driver itself. I
couldn't find new users of this algorithm since, so there should be no
one depending on the new behaviour.
Reported-by: NSergey Larin <cerg2010cerg2010@mail.ru>
Fixes: 3e5f06be ("i2c: algo-bit: init the bus to a known state")
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Tested-by: NSergey Larin <cerg2010cerg2010@mail.ru>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

Currently device_supports_dax() just checks to see if the QUEUE_FLAG_DAX
flag is set on the device's request queue to decide whether or not the
device supports filesystem DAX.  Really we should be using
bdev_dax_supported() like filesystems do at mount time.  This performs
other tests like checking to make sure the dax_direct_access() path works.

We also explicitly clear QUEUE_FLAG_DAX on the DM device's request queue if
any of the underlying devices do not support DAX.  This makes the handling
of QUEUE_FLAG_DAX consistent with the setting/clearing of most other flags
in dm_table_set_restrictions().

Now that bdev_dax_supported() explicitly checks for QUEUE_FLAG_DAX, this
will ensure that filesystems built upon DM devices will only be able to
mount with DAX if all underlying devices also support DAX.
Signed-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Fixes: commit 545ed20e ("dm: add infrastructure for DAX support")
Cc: stable@vger.kernel.org
Acked-by: NDan Williams <dan.j.williams@intel.com>
Reviewed-by: NToshi Kani <toshi.kani@hpe.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Add an explicit check for QUEUE_FLAG_DAX to __bdev_dax_supported().  This
is needed for DM configurations where the first element in the dm-linear or
dm-stripe target supports DAX, but other elements do not.  Without this
check __bdev_dax_supported() will pass for such devices, letting a
filesystem on that device mount with the DAX option.
Signed-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: NMike Snitzer <snitzer@redhat.com>
Fixes: commit 545ed20e ("dm: add infrastructure for DAX support")
Cc: stable@vger.kernel.org
Acked-by: NDan Williams <dan.j.williams@intel.com>
Reviewed-by: NToshi Kani <toshi.kani@hpe.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

QUEUE_FLAG_DAX is an indication that a given block device supports
filesystem DAX and should not be set for PMEM namespaces which are in "raw"
mode.  These namespaces lack struct page and are prevented from
participating in filesystem DAX as of commit 569d0365 ("dax: require
'struct page' by default for filesystem dax").
Signed-off-by: NRoss Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: NMike Snitzer <snitzer@redhat.com>
Fixes: 569d0365 ("dax: require 'struct page' by default for filesystem dax")
Cc: stable@vger.kernel.org
Acked-by: NDan Williams <dan.j.williams@intel.com>
Reviewed-by: NToshi Kani <toshi.kani@hpe.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

The poll() changes were not well thought out, and completely
unexplained.  They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.

Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead.  That gets rid of one of the new indirections.

But that doesn't fix the new complexity that is completely unwarranted
for the regular case.  The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.

[ This revert is a revert of about 30 different commits, not reverted
  individually because that would just be unnecessarily messy  - Linus ]

Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If reconnect/reset failed where the controller async event buffer
was freed, we might end up freeing it again as we call
nvme_rdma_destroy_admin_queue again in the remove path. Given that
the sequence is guaranteed to serialize by .ctrl_stop, we simply
set ctrl->async_event_sqe.data to NULL and don't free it in future
visits.
Reported-by: NMax Gurtovoy <maxg@mellanox.com>
Tested-by: NMax Gurtovoy <maxg@mellanox.com>
Signed-off-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

KMSAN reported an infoleak when reading from /dev/vcs*:

  BUG: KMSAN: kernel-infoleak in vcs_read+0x18ba/0x1cc0
  Call Trace:
  ...
   kmsan_copy_to_user+0x7a/0x160 mm/kmsan/kmsan.c:1253
   copy_to_user ./include/linux/uaccess.h:184
   vcs_read+0x18ba/0x1cc0 drivers/tty/vt/vc_screen.c:352
   __vfs_read+0x1b2/0x9d0 fs/read_write.c:416
   vfs_read+0x36c/0x6b0 fs/read_write.c:452
  ...
  Uninit was created at:
   kmsan_save_stack_with_flags mm/kmsan/kmsan.c:279
   kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:189
   kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:315
   __kmalloc+0x13a/0x350 mm/slub.c:3818
   kmalloc ./include/linux/slab.h:517
   vc_allocate+0x438/0x800 drivers/tty/vt/vt.c:787
   con_install+0x8c/0x640 drivers/tty/vt/vt.c:2880
   tty_driver_install_tty drivers/tty/tty_io.c:1224
   tty_init_dev+0x1b5/0x1020 drivers/tty/tty_io.c:1324
   tty_open_by_driver drivers/tty/tty_io.c:1959
   tty_open+0x17b4/0x2ed0 drivers/tty/tty_io.c:2007
   chrdev_open+0xc25/0xd90 fs/char_dev.c:417
   do_dentry_open+0xccc/0x1440 fs/open.c:794
   vfs_open+0x1b6/0x2f0 fs/open.c:908
  ...
  Bytes 0-79 of 240 are uninitialized

Consistently allocating |vc_screenbuf| with kzalloc() fixes the problem

Reported-by: syzbot+17a8efdf800000@syzkaller.appspotmail.com
Signed-off-by: NAlexander Potapenko <glider@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to free all resources associated with the ida on module
exit.

Fixes: cd6484e1 ("serdev: Introduce new bus for serial attached devices")
Cc: stable <stable@vger.kernel.org>	# 4.11
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

After the commit

  7d8905d0 ("serial: 8250_pci: Enable device after we check black list")

pure serial multi-port cards, such as CH355, got blacklisted and thus
not being enumerated anymore. Previously, it seems, blacklisting them
was on purpose to shut up pciserial_init_one() about record duplication.

So, remove the entries from blacklist in order to get cards enumerated.

Fixes: 7d8905d0 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: NMatt Turner <mattst88@gmail.com>
Cc: Sergej Pupykin <ml@sergej.pp.ru>
Cc: Alexandr Petrenko <petrenkoas83@gmail.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-and-Tested-by: NMatt Turner <mattst88@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

syzbot is reporting stalls at __process_echoes() [1]. This is because
since ldata->echo_commit < ldata->echo_tail becomes true for some reason,
the discard loop is serving as almost infinite loop. This patch tries to
avoid falling into ldata->echo_commit < ldata->echo_tail situation by
making access to echo_* variables more carefully.

Since reset_buffer_flags() is called without output_lock held, it should
not touch echo_* variables. And omit a call to reset_buffer_flags() from
n_tty_open() by using vzalloc().

Since add_echo_byte() is called without output_lock held, it needs memory
barrier between storing into echo_buf[] and incrementing echo_head counter.
echo_buf() needs corresponding memory barrier before reading echo_buf[].
Lack of handling the possibility of not-yet-stored multi-byte operation
might be the reason of falling into ldata->echo_commit < ldata->echo_tail
situation, for if I do WARN_ON(ldata->echo_commit == tail + 1) prior to
echo_buf(ldata, tail + 1), the WARN_ON() fires.

Also, explicitly masking with buffer for the former "while" loop, and
use ldata->echo_commit > tail for the latter "while" loop.

[1] https://syzkaller.appspot.com/bug?id=17f23b094cd80df750e5b0f8982c521ee6bcbf40Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Nsyzbot <syzbot+108696293d7a21ab688f@syzkaller.appspotmail.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

syzbot is reporting stalls at n_tty_receive_char_special() [1]. This is
because comparison is not working as expected since ldata->read_head can
change at any moment. Mitigate this by explicitly masking with buffer size
when checking condition for "while" loops.

[1] https://syzkaller.appspot.com/bug?id=3d7481a346958d9469bebbeb0537d5f056bdd6e8Signed-off-by: NTetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: Nsyzbot <syzbot+18df353d7540aa6b5467@syzkaller.appspotmail.com>
Fixes: bc5a5e3f ("n_tty: Don't wrap input buffer indices at buffer size")
Cc: stable <stable@vger.kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The only thing that omap_gem_free_object does that might need the magic
protection of struct_mutex (of keeping all objects alive if that lock is
held, even if the last reference is gone) is the mm_list manipulation.
This is already protected by the separate omapdrm->list_lock, which
means that struct_mutex is not needed by omapdrm. We can switch to
gem_free_object_unlocked()
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

- None of the list walkings where protected.

- Switch to a mutex since the list walking at device resume time can
  sleep when pinning buffers through the tiler.

Only thing we need to be careful with here is that while we walk the
list we can't unreference any gem objects, since the final unref would
result in a recursive deadlock. But the only functions that walk the
list is the device resume and debugfs dumping, so all safe.
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The DRM device struct_mutex is used to protect against concurrent GEM
object operations that deal with memory allocation and pinning. All
those operations are local to a GEM object and don't need to be
serialized across different GEM objects. Replace the struct_mutex with
a local omap_obj.lock or drop it altogether where not needed.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

GEM objects mmap offsets are created by calling
drm_gem_create_mmap_offset_size() that doesn't need struct_mutex
protection as it includes its own locking, based on a size that is
static across the object's life time. Remove the unneeded struct_mutex
locking.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The __omap_gem_get_pages() function is a wrapper around
omap_gem_attach_pages() that returns the omap_obj->pages pointer through
a function argument. Some callers don't need the pages pointer, and all
of them can access omap_obj->pages directly. To simplify the code merge
the __omap_gem_get_pages() wrapper with omap_gem_attach_pages() and
update the callers accordingly.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

get_pages() as a local function name is too generic and easily confused
for a generic MM kernel function. Rename it to __omap_gem_get_pages().

Rename the is_contiguous(), is_cache_coherent(), evict(), evict_entry(),
fault_1d() and fault_2d() functions for the same reason.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Change tomi.valkeinen@nokia.com to tomi.valkeinen@ti.com.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Description of DRA7 Errata i932:

In rare circumstances DPLL_VIDEO1 and DPLL_VIDEO2 PLL's may not lock on
the first attempt during DSS initialization. When this occurs, a
subsequent attempt to relock the PLL will result in PLL successfully
locking.

This patch does the following as per the errata recommendation:

- retries locking the PLL upto 20 times.

- The time to wait for a PLL lock set to 1000 REFCLK cycles. We use
usleep_range to wait for 1000 REFCLK cycles in the us range. This tight
constraint is imposed as a lock later than 1000 REFCLK cycles may have
high jitter.

- Criteria for PLL lock is extended from check on just the PLL_LOCK bit
to check on 6 PLL_STATUS bits.

Silicon Versions Impacted:
DRA71, DRA72, DRA74, DRA76 - All silicon revisions
AM57x - All silicon revisions

OMAP4/5 are not impacted by this errata
Signed-off-by: NVenkateswara Rao Mandela <venkat.mandela@ti.com>
[tomi.valkeinen@ti.com: ported to v4.14]
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Use new return type vm_fault_t for fault handler. For
now, this is just documenting that the function returns
a VM_FAULT value rather than an errno. Once all instances
are converted, vm_fault_t will become a distinct type.

Ref-> commit 1c8f4220 ("mm: change return type to vm_fault_t")

Previously vm_insert_mixed() returns err which driver
mapped into VM_FAULT_* type. Also return value of
vm_insert_mixed() not handled correctly and 0 was
returned inside fault_2d() as default. The new function
vmf_insert_mixed() will replace this inefficiency by
returning correct VM_FAULT_* type.

vmf_error() is the newly introduce inline function
in 4.17-rc6.
Signed-off-by: NSouptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: NMatthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

drm_of_find_possible_crtcs() doesn't work when DW HDMI encoder is
connected to TCON (crtc) through mux in TCON TOP.

In that case TCON TOP HDMI mux input port has to be manually traversed
and checked if it matches any known crtc.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-23-jernej.skrabec@siol.net

Function is useful when drm_of_find_possible_crtcs() can't be used and
custom parsing is needed. This can happen for example when there is a
node with multiple muxes between crtc and encoder.
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
[maxime: change the function to have a consistent prefix]
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-22-jernej.skrabec@siol.net

PHY is the same as in H3, except it can switch between two clock
parents.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-21-jernej.skrabec@siol.net

Expand HDMI PHY clock driver to support second clock parent.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-20-jernej.skrabec@siol.net

Some DW HDMI PHYs, like those found in A64 and R40 SoCs, can select
between two clock parents.

Add code which reads second PLL from DT.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-19-jernej.skrabec@siol.net

DW HDMI PHY driver and PHY clock driver share same registers. Make sure
that DW HDMI PHY setup code doesn't change any clock related bits.
During initialization, set PHY PLL parent bit to 0.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-18-jernej.skrabec@siol.net

Current DW HDMI PHY code never prepares and enables PHY clock after it is
created. It's just used as it is. This may work in some cases, but it's
clearly wrong. Fix it by adding proper calls to enable/disable PHY
clock.

Fixes: 4f86e817 ("drm/sun4i: Add support for H3 HDMI PHY variant")
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-17-jernej.skrabec@siol.net

Both mixers have similar capabilities as others SoCs with DE2.

First mixer has 1 VI and 3 UI planes and supports HW scaling on all
planes.

Second mixer has 1 VI and 1 UI planes and also supports HW scaling on
all planes.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-15-jernej.skrabec@siol.net

TV TCONs are always connected to TV or HDMI encoder, so it doesn't make
sense to check if panel or bridge is connected to them.

Check if TCON has channel 0 and only then check for connected panel or
bridges.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-13-jernej.skrabec@siol.net

LVDS and RGB interfaces are always connected to TCONs which have channel
0. It doesn't make sense to try to init them on TV TCONs.

Add a check if TCON has channel 0 before trying to init LVDS or RGB
interface.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-12-jernej.skrabec@siol.net

Current "old" method to find engine worked pretty well for DE2. However,
it doesn't work when TCON TOP is between  mixer (engine) and TCON. TCON
TOP has multiple input ports, but current engine search algorithm
expects only one.

This can be fixed by first looking for output port id and selecting
matching input by subtracting 1 for the next round. This work even if
there is only one input and output.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-11-jernej.skrabec@siol.net

TV TCONs (channel 1 only) are always connected to TV or HDMI encoder.
Because of that, all output endpoints on such TCON node will point to a
encoder which is part of component framework.

Correct current graph traversing algorithm in such way that it doesn't
skip output enpoints with id 0 on TV TCONs.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-10-jernej.skrabec@siol.net

TCON TOP is different from other nodes in graph by having 3 input and 3
output ports. Additionally, connection to TV TCON might lead back to
HDMI mux input port, creating loops.

Add support for traversing such graph.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-9-jernej.skrabec@siol.net

Until now, each node has one input port and one output port. However,
with TCON TOP this is no longer true. It has 3 input and 3 output ports.

In order to prepare to this situation, split out the code which checks
all endpoints in input port and adds available components to fifo.

This patch doesn't do any functional change.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-8-jernej.skrabec@siol.net

sun4i_drv_add_endpoints() has a memory leak since it uses of_node_put()
when remote is equal to NULL and does nothing when remote has a valid
pointer.

Invert the logic to fix memory leak.
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180625120304.7543-7-jernej.skrabec@siol.net