We were erroneously assigning the new configuration to a local
variable cfg, but that was not being assigned to anything, so the
change was getting lost.  Assign directly to iwl_trans->cfg instead.

Fixes: 5a8c31aa ("iwlwifi: pcie: fix recognition of QuZ devices")
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

mwifiex_update_vs_ie(),mwifiex_set_uap_rates() and
mwifiex_set_wmm_params() call memcpy() without checking
the destination size.Since the source is given from
user-space, this may trigger a heap buffer overflow.

Fix them by putting the length check before performing memcpy().

This fix addresses CVE-2019-14814,CVE-2019-14815,CVE-2019-14816.
Signed-off-by: NWen Huang <huangwenabc@gmail.com>
Acked-by: NGanapathi Bhat <gbhat@marvell.comg>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

MT7630E hardware does support 5GHz, but we do not properly configure phy
for 5GHz channels. Scanning at this band not only do not show any APs
but also can hang the firmware.

Since vendor reference driver do not support 5GHz we don't know how
properly configure 5GHz channels. So disable this band for MT7630E .

Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Since 41634aa8 ("mt76: only schedule txqs from the tx tasklet")
I can observe firmware hangs on MT7630E on station mode: tx stop
functioning after minor activity (rx keep working) and on module
unload device fail to stop with messages:

[ 5446.141413] mt76x0e 0000:06:00.0: TX DMA did not stop
[ 5449.176764] mt76x0e 0000:06:00.0: TX DMA did not stop

Loading module again results in failure to associate with AP.
Only machine power off / power on cycle can make device work again.

It's unclear why commit 41634aa8 causes the problem, but it is
related to HW encryption. Since issue is a firmware hang, that is super
hard to debug, just disable HW encryption as fix for the issue.

Fixes: 41634aa8 ("mt76: only schedule txqs from the tx tasklet")
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Pull char/misc driver fixes from Greg KH:
 "Here are some small char and misc driver fixes for reported issues for
  5.3-rc7

  Also included in here is the documentation for how we are handling
  hardware issues under embargo that everyone has finally agreed on, as
  well as a MAINTAINERS update for the suckers who agreed to handle the
  LICENSES/ files.

  All of these have been in linux-next last week with no reported
  issues"

* tag 'char-misc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  fsi: scom: Don't abort operations for minor errors
  vmw_balloon: Fix offline page marking with compaction
  VMCI: Release resource if the work is already queued
  Documentation/process: Embargoed hardware security issues
  lkdtm/bugs: fix build error in lkdtm_EXHAUST_STACK
  mei: me: add Tiger Lake point LP device ID
  intel_th: pci: Add Tiger Lake support
  intel_th: pci: Add support for another Lewisburg PCH
  stm class: Fix a double free of stm_source_device
  MAINTAINERS: add entry for LICENSES and SPDX stuff
  fpga: altera-ps-spi: Fix getting of optional confd gpio

Pull USB fixes from Greg KH:
 "Here are some small USB fixes that have been in linux-next this past
  week for 5.3-rc7

  They fix the usual xhci, syzbot reports, and other small issues that
  have come up last week.

  All have been in linux-next with no reported issues"

* tag 'usb-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: cdc-wdm: fix race between write and disconnect due to flag abuse
  usb: host: xhci: rcar: Fix typo in compatible string matching
  usb: host: xhci-tegra: Set DMA mask correctly
  USB: storage: ums-realtek: Whitelist auto-delink support
  USB: storage: ums-realtek: Update module parameter description for auto_delink_en
  usb: host: ohci: fix a race condition between shutdown and irq
  usb: hcd: use managed device resources
  typec: tcpm: fix a typo in the comparison of pdo_max_voltage
  usb-storage: Add new JMS567 revision to unusual_devs
  usb: chipidea: udc: don't do hardware access if gadget has stopped
  usbtmc: more sanity checking for packet size
  usb: udc: lpc32xx: silence fall-through warning

Pull networking fixes from David Miller:

 1) Fix some length checks during OGM processing in batman-adv, from
    Sven Eckelmann.

 2) Fix regression that caused netfilter conntrack sysctls to not be
    per-netns any more. From Florian Westphal.

 3) Use after free in netpoll, from Feng Sun.

 4) Guard destruction of pfifo_fast per-cpu qdisc stats with
    qdisc_is_percpu_stats(), from Davide Caratti. Similar bug is fixed
    in pfifo_fast_enqueue().

 5) Fix memory leak in mld_del_delrec(), from Eric Dumazet.

 6) Handle neigh events on internal ports correctly in nfp, from John
    Hurley.

 7) Clear SKB timestamp in NF flow table code so that it does not
    confuse fq scheduler. From Florian Westphal.

 8) taprio destroy can crash if it is invoked in a failure path of
    taprio_init(), because the list head isn't setup properly yet and
    the list del is unconditional. Perform the list add earlier to
    address this. From Vladimir Oltean.

 9) Make sure to reapply vlan filters on device up, in aquantia driver.
    From Dmitry Bogdanov.

10) sgiseeq driver releases DMA memory using free_page() instead of
    dma_free_attrs(). From Christophe JAILLET.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
  net: seeq: Fix the function used to release some memory in an error handling path
  enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
  net: bcmgenet: use ethtool_op_get_ts_info()
  tc-testing: don't hardcode 'ip' in nsPlugin.py
  net: dsa: microchip: add KSZ8563 compatibility string
  dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
  net: aquantia: fix out of memory condition on rx side
  net: aquantia: linkstate irq should be oneshot
  net: aquantia: reapply vlan filters on up
  net: aquantia: fix limit of vlan filters
  net: aquantia: fix removal of vlan 0
  net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
  taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
  taprio: Fix kernel panic in taprio_destroy
  net: dsa: microchip: fill regmap_config name
  rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]
  net: stmmac: dwmac-rk: Don't fail if phy regulator is absent
  amd-xgbe: Fix error path in xgbe_mod_init()
  netfilter: nft_meta_bridge: Fix get NFT_META_BRI_IIFVPROTO in network byteorder
  mac80211: Correctly set noencrypt for PAE frames
  ...

In commit 99cd149e ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.

Fix it now.

Rename the corresponding label to something more in line.

Fixes: 99cd149e ("sgiseeq: replace use of dma_cache_wback_inv")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: NThomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for x86:

   - Fix the bogus detection of 32bit user mode for uretprobes which
     caused corruption of the user return address resulting in
     application crashes. In the uprobes handler in_ia32_syscall() is
     obviously always returning false on a 64bit kernel. Use
     user_64bit_mode() instead which works correctly.

   - Prevent large page splitting when ftrace flips RW/RO on the kernel
     text which caused iTLB performance issues. Ftrace wants to be
     converted to text_poke() which avoids the problem, but for now
     allow large page preservation in the static protections check when
     the change request spawns a full large page.

   - Prevent arch_dynirq_lower_bound() from returning 0 when the IOAPIC
     is configured via device tree. In the device tree case the GSI 1:1
     mapping is meaningless therefore the lower bound which protects the
     GSI range on ACPI machines is irrelevant. Return the lower bound
     which the core hands to the function instead of blindly returning 0
     which causes the core to allocate the invalid virtual interupt
     number 0 which in turn prevents all drivers from allocating and
     requesting an interrupt.

   - Remove the bogus initialization of LDR and DFR in the 32bit bigsmp
     APIC driver. That uses physical destination mode where LDR/DFR are
     ignored, but the initialization and the missing clear of LDR caused
     the APIC to be left in a inconsistent state on kexec/reboot.

   - Clear LDR when clearing the APIC registers so the APIC is in a well
     defined state.

   - Initialize variables proper in the find_trampoline_placement()
     code.

   - Silence GCC( build warning for the real mode part of the build"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm/cpa: Prevent large page split when ftrace flips RW on kernel text
  x86/build: Add -Wnoaddress-of-packed-member to REALMODE_CFLAGS, to silence GCC9 build warning
  x86/boot/compressed/64: Fix missing initialization in find_trampoline_placement()
  x86/apic: Include the LDR when clearing out APIC registers
  x86/apic: Do not initialize LDR and DFR for bigsmp
  uprobes/x86: Fix detection of 32-bit user mode
  x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machines

Pull perf fixes from Thomas Gleixner:
 "Two fixes for perf x86 hardware implementations:

   - Restrict the period on Nehalem machines to prevent perf from
     hogging the CPU

   - Prevent the AMD IBS driver from overwriting the hardwre controlled
     and pre-seeded reserved bits (0-6) in the count register which
     caused a sample bias for dispatched micro-ops"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/amd/ibs: Fix sample bias for dispatched micro-ops
  perf/x86/intel: Restrict period on Nehalem

Pull turbostat updates from Len Brown:
 "User-space turbostat (and x86_energy_perf_policy) patches.

  They are primarily bug fixes from users"

* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: update version number
  tools/power turbostat: Add support for Hygon Fam 18h (Dhyana) RAPL
  tools/power turbostat: Fix caller parameter of get_tdp_amd()
  tools/power turbostat: Fix CPU%C1 display value
  tools/power turbostat: do not enforce 1ms
  tools/power turbostat: read from pipes too
  tools/power turbostat: Add Ice Lake NNPI support
  tools/power turbostat: rename has_hsw_msrs()
  tools/power turbostat: Fix Haswell Core systems
  tools/power turbostat: add Jacobsville support
  tools/power turbostat: fix buffer overrun
  tools/power turbostat: fix file descriptor leaks
  tools/power turbostat: fix leak of file descriptor on error return path
  tools/power turbostat: Make interval calculation per thread to reduce jitter
  tools/power turbostat: remove duplicate pc10 column
  tools/power x86_energy_perf_policy: Fix argument parsing
  tools/power: Fix typo in man page
  tools/power/x86: Enable compiler optimisations and Fortify by default
  tools/power x86_energy_perf_policy: Fix "uninitialized variable" warnings at -O2

Call to 'pci_free_irq_vectors()' are missing both in the error handling
path of the probe function, and in the remove function.
Add them.

Fixes: 19971f5e ("enetc: add PTP clock driver")
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change enables the use of SW timestamping on the Raspberry Pi 4.

bcmgenet's transmit function bcmgenet_xmit() implements software
timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE capability was
missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced. By using
ethtool_ops bcmgenet_ethtool_ops() as get_ts_info(), the
SOF_TIMESTAMPING_TX_SOFTWARE capability is announced.

Similar to commit a8f5cb9e ("smsc95xx: use ethtool_op_get_ts_info()")
Signed-off-by: NRyan M. Collins <rmc032@bucknell.edu>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NDoug Berger <opendmb@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the following tdc test fails on Fedora:

 # ./tdc.py -e 2638
  -- ns/SubPlugin.__init__
 Test 2638: Add matchall and try to get it
 -----> prepare stage *** Could not execute: "$TC qdisc add dev $DEV1 clsact"
 -----> prepare stage *** Error message: "/bin/sh: ip: command not found"
 returncode 127; expected [0]
 -----> prepare stage *** Aborting test run.

Let nsPlugin.py use the 'IP' variable introduced with commit 92c1a19e
("tc-tests: added path to ip command in tdc"), so that the path to 'ip' is
correctly resolved to the value we have in tdc_config.py.

 # ./tdc.py -e 2638
  -- ns/SubPlugin.__init__
 Test 2638: Add matchall and try to get it
 All test results:
 1..1
 ok 1 2638 - Add matchall and try to get it

Fixes: 489ce2f4 ("tc-testing: Restore original behaviour for namespaces in tdc")
Reported-by: NHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Razvan Stefanescu says:

====================
net: dsa: microchip: add KSZ8563 support

This patchset adds compatibility string for the KSZ8563 switch.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is a 3-Port 10/100 Ethernet Switch with 1588v2 PTP.
Signed-off-by: NRazvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is a 3-Port 10/100 Ethernet Switch with 1588v2 PTP.
Signed-off-by: NRazvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Igor Russkikh says:

====================
net: aquantia: fixes on vlan filters and other conditions

Here is a set of various bug fixes related to vlan filter offload and
two other rare cases.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On embedded environments with hard memory limits it is a normal although
rare case when skb can't be allocated on rx part under high traffic.

In such OOM cases napi_complete_done() was not called.
So the napi object became in an invalid state like it is "scheduled".
Kernel do not re-schedules the poll of that napi object.

Consequently, kernel can not remove that object the system hangs on
`ifconfig down` waiting for a poll.

We are fixing this by gracefully closing napi poll routine with correct
invocation of napi_complete_done.

This was reproduced with artificially failing the allocation of skb to
simulate an "out of memory" error case and check that traffic does
not get stuck.

Fixes: 970a2e98 ("net: ethernet: aquantia: Vector operations")
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Declaring threaded irq handler should also indicate the irq is
oneshot. It is oneshot indeed, because HW implements irq automasking
on trigger.

Not declaring this causes some kernel configurations to fail
on interface up, because request_threaded_irq returned an err code.

The issue was originally hidden on normal x86_64 configuration with
latest kernel, because depending on interrupt controller, irq driver
added ONESHOT flag on its own.

Issue was observed on older kernels (4.14) where no such logic exists.

Fixes: 4c83f170 ("net: aquantia: link status irq handling")
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Reported-by: NMichael Symolkin <Michael.Symolkin@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of device reconfiguration the driver may reset the device invisible
for other modules, vlan module in particular. So vlans will not be
removed&created and vlan filters will not be configured in the device.
The patch reapplies the vlan filters at device start.

Fixes: 7975d2af ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a limit condition of vlans on the interface before setting vlan
promiscuous mode

Fixes: 48dd73d0 ("net: aquantia: fix vlans not working over bridged network")
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to absence of checking against the rx flow rule when vlan 0 is being
removed, the other rule could be removed instead of the rule with vlan 0

Fixes: 7975d2af ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: NDmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: NIgor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Fix issues in tc-taprio and tc-cbs

This series fixes one panic and one WARN_ON found in the tc-taprio
qdisc, while trying to apply it:

- On an interface which is not multi-queue
- On an interface which has no carrier

The tc-cbs was also visually found to suffer of the same issue as
tc-taprio, and the fix was only compile-tested in that case.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The discussion to be made is absolutely the same as in the case of
previous patch ("taprio: Set default link speed to 10 Mbps in
taprio_set_picos_per_byte"). Nothing is lost when setting a default.

Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com>
Fixes: e0a7683d ("net/sched: cbs: fix port_rate miscalculation")
Acked-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The taprio budget needs to be adapted at runtime according to interface
link speed. But that handling is problematic.

For one thing, installing a qdisc on an interface that doesn't have
carrier is not illegal. But taprio prints the following stack trace:

[   31.851373] ------------[ cut here ]------------
[   31.856024] WARNING: CPU: 1 PID: 207 at net/sched/sch_taprio.c:481 taprio_dequeue+0x1a8/0x2d4
[   31.864566] taprio: dequeue() called with unknown picos per byte.
[   31.864570] Modules linked in:
[   31.873701] CPU: 1 PID: 207 Comm: tc Not tainted 5.3.0-rc5-01199-g8838fe023cd6 #1689
[   31.881398] Hardware name: Freescale LS1021A
[   31.885661] [<c03133a4>] (unwind_backtrace) from [<c030d8cc>] (show_stack+0x10/0x14)
[   31.893368] [<c030d8cc>] (show_stack) from [<c10ac958>] (dump_stack+0xb4/0xc8)
[   31.900555] [<c10ac958>] (dump_stack) from [<c0349d04>] (__warn+0xe0/0xf8)
[   31.907395] [<c0349d04>] (__warn) from [<c0349d64>] (warn_slowpath_fmt+0x48/0x6c)
[   31.914841] [<c0349d64>] (warn_slowpath_fmt) from [<c0f38db4>] (taprio_dequeue+0x1a8/0x2d4)
[   31.923150] [<c0f38db4>] (taprio_dequeue) from [<c0f227b0>] (__qdisc_run+0x90/0x61c)
[   31.930856] [<c0f227b0>] (__qdisc_run) from [<c0ec82ac>] (net_tx_action+0x12c/0x2bc)
[   31.938560] [<c0ec82ac>] (net_tx_action) from [<c0302298>] (__do_softirq+0x130/0x3c8)
[   31.946350] [<c0302298>] (__do_softirq) from [<c03502a0>] (irq_exit+0xbc/0xd8)
[   31.953536] [<c03502a0>] (irq_exit) from [<c03a4808>] (__handle_domain_irq+0x60/0xb4)
[   31.961328] [<c03a4808>] (__handle_domain_irq) from [<c0754478>] (gic_handle_irq+0x58/0x9c)
[   31.969638] [<c0754478>] (gic_handle_irq) from [<c0301a8c>] (__irq_svc+0x6c/0x90)
[   31.977076] Exception stack(0xe8167b20 to 0xe8167b68)
[   31.982100] 7b20: e9d4bd80 00000cc0 000000cf 00000000 e9d4bd80 c1f38958 00000cc0 c1f38960
[   31.990234] 7b40: 00000001 000000cf 00000004 e9dc0800 00000000 e8167b70 c0f478ec c0f46d94
[   31.998363] 7b60: 60070013 ffffffff
[   32.001833] [<c0301a8c>] (__irq_svc) from [<c0f46d94>] (netlink_trim+0x18/0xd8)
[   32.009104] [<c0f46d94>] (netlink_trim) from [<c0f478ec>] (netlink_broadcast_filtered+0x34/0x414)
[   32.017930] [<c0f478ec>] (netlink_broadcast_filtered) from [<c0f47cec>] (netlink_broadcast+0x20/0x28)
[   32.027102] [<c0f47cec>] (netlink_broadcast) from [<c0eea378>] (rtnetlink_send+0x34/0x88)
[   32.035238] [<c0eea378>] (rtnetlink_send) from [<c0f25890>] (notify_and_destroy+0x2c/0x44)
[   32.043461] [<c0f25890>] (notify_and_destroy) from [<c0f25e08>] (qdisc_graft+0x398/0x470)
[   32.051595] [<c0f25e08>] (qdisc_graft) from [<c0f27a00>] (tc_modify_qdisc+0x3a4/0x724)
[   32.059470] [<c0f27a00>] (tc_modify_qdisc) from [<c0ee4c84>] (rtnetlink_rcv_msg+0x260/0x2ec)
[   32.067864] [<c0ee4c84>] (rtnetlink_rcv_msg) from [<c0f4a988>] (netlink_rcv_skb+0xb8/0x110)
[   32.076172] [<c0f4a988>] (netlink_rcv_skb) from [<c0f4a170>] (netlink_unicast+0x1b4/0x22c)
[   32.084392] [<c0f4a170>] (netlink_unicast) from [<c0f4a5e4>] (netlink_sendmsg+0x33c/0x380)
[   32.092614] [<c0f4a5e4>] (netlink_sendmsg) from [<c0ea9f40>] (sock_sendmsg+0x14/0x24)
[   32.100403] [<c0ea9f40>] (sock_sendmsg) from [<c0eaa780>] (___sys_sendmsg+0x214/0x228)
[   32.108279] [<c0eaa780>] (___sys_sendmsg) from [<c0eabad0>] (__sys_sendmsg+0x50/0x8c)
[   32.116068] [<c0eabad0>] (__sys_sendmsg) from [<c0301000>] (ret_fast_syscall+0x0/0x54)
[   32.123938] Exception stack(0xe8167fa8 to 0xe8167ff0)
[   32.128960] 7fa0:                   b6fa68c8 000000f8 00000003 bea142d0 00000000 00000000
[   32.137093] 7fc0: b6fa68c8 000000f8 0052154c 00000128 5d6468a2 00000000 00000028 00558c9c
[   32.145224] 7fe0: 00000070 bea14278 00530d64 b6e17e64
[   32.150659] ---[ end trace 2139c9827c3e5177 ]---

This happens because the qdisc ->dequeue callback gets called. Which
again is not illegal, the qdisc will dequeue even when the interface is
up but doesn't have carrier (and hence SPEED_UNKNOWN), and the frames
will be dropped further down the stack in dev_direct_xmit().

And, at the end of the day, for what? For calculating the initial budget
of an interface which is non-operational at the moment and where frames
will get dropped anyway.

So if we can't figure out the link speed, default to SPEED_10 and move
along. We can also remove the runtime check now.

Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com>
Fixes: 7b9eba7b ("net/sched: taprio: fix picos_per_byte miscalculation")
Acked-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

taprio_init may fail earlier than this line:

	list_add(&q->taprio_list, &taprio_list);

i.e. due to the net device not being multi queue.

Attempting to remove q from the global taprio_list when it is not part
of it will result in a kernel panic.

Fix it by matching list_add and list_del better to one another in the
order of operations. This way we can keep the deletion unconditional
and with lower complexity - O(1).

Cc: Leandro Dorileo <leandro.maciel.dorileo@intel.com>
Fixes: 7b9eba7b ("net/sched: taprio: fix picos_per_byte miscalculation")
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Acked-by: NVinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the register value width as the regmap_config name to prevent the
following error when the second and third regmap_configs are
initialized.
 "debugfs: Directory '${bus-id}' with parent 'regmap' already present!"
Signed-off-by: NGeorge McCollister <george.mccollister@gmail.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here are two batman-adv bugfixes:

 - Fix OGM and OGMv2 header read boundary check,
   by Sven Eckelmann (2 patches)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Today is 19.08.31, at least in some parts of the world.
Signed-off-by: NLen Brown <len.brown@intel.com>

Commit 9392bd98 ("tools/power turbostat: Add support for AMD
Fam 17h (Zen) RAPL") and the commit 3316f99a ("tools/power
turbostat: Also read package power on AMD F17h (Zen)") add AMD Fam 17h
RAPL support.

Hygon Family 18h(Dhyana) support RAPL in bit 14 of CPUID 0x80000007 EDX,
and has MSRs RAPL_PWR_UNIT/CORE_ENERGY_STAT/PKG_ENERGY_STAT. So add Hygon
Dhyana Family 18h support for RAPL.

Already tested on Hygon multi-node systems and it shows correct per-core
energy usage and the total package power.
Signed-off-by: NPu Wen <puwen@hygon.cn>
Reviewed-by: NCalvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: NLen Brown <len.brown@intel.com>

Commit 9392bd98 ("tools/power turbostat: Add support for AMD
Fam 17h (Zen) RAPL") add a function get_tdp_amd(), the parameter is CPU
family. But the rapl_probe_amd() function use wrong model parameter.
Fix the wrong caller parameter of get_tdp_amd() to use family.

Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: NPu Wen <puwen@hygon.cn>
Reviewed-by: NCalvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: NLen Brown <len.brown@intel.com>

In some case C1% will be wrong value, when platform doesn't have MSR for
C1 residency.

For example:
Core    CPU     CPU%c1
-       -       100.00
0       0       100.00
0       2       100.00
1       1       100.00
1       3       100.00

But adding Busy% will fix this
Core    CPU     Busy%   CPU%c1
-       -       99.77   0.23
0       0       99.77   0.23
0       2       99.77   0.23
1       1       99.77   0.23
1       3       99.77   0.23

This issue can be reproduced on most of the recent systems including
Broadwell, Skylake and later.

This is because if we don't select Busy% or Avg_MHz or Bzy_MHz then
mperf value will not be read from MSR, so it will be 0. But this
is required for C1% calculation when MSR for C1 residency is not present.
Same is true for C3, C6 and C7 column selection.

So add another define DO_BIC_READ(), which doesn't depend on user
column selection and use for mperf, C3, C6 and C7 related counters.
So when there is no platform support for C1 residency counters,
we still read these counters, if the CPU has support and user selected
display of CPU%c1.
Signed-off-by: NSrinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Turbostat works by taking a snapshot of counters, sleeping, taking another
snapshot, calculating deltas, and printing out the table.

The sleep time is controlled via -i option or by user sending a signal or a
character to stdin. In the latter case, turbostat always adds 1 ms
sleep before it reads the counters, in order to avoid larger imprecisions
in the results in prints.

While the 1 ms delay may be a good idea for a "dumb" user, it is a
problem for an "aware" user. I do thousands and thousands of measurements
over a short period of time (like 2ms), and turbostat unconditionally adds
a 1ms to my interval, so I cannot get what I really need.

This patch removes the unconditional 1ms sleep. This is an expert user
tool, after all, and non-experts will unlikely ever use it in the non-fixed
interval mode anyway, so I think it is OK to remove the 1ms delay.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Commit '47936f94 tools/power turbostat: fix printing on input' make
a valid fix, but it completely disabled piped stdin support, which is
a valuable use-case. Indeed, if stdin is a pipe, turbostat won't read
anything from it, so it becomes impossible to get turbostat output at
user-defined moments, instead of the regular intervals.

There is no reason why this should works for terminals, but not for
pipes. This patch improves the situation. Instead of ignoring pipes, we
read data from them but gracefully handle the EOF case.
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This enables turbostat utility on Ice Lake NNPI SoC.

Link: https://lkml.org/lkml/2019/6/5/1034Signed-off-by: NRajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Perhaps if this more descriptive name had been used,
then we wouldn't have had the HSW ULT vs HSW CORE bug,
fixed by the previous commit.
Signed-off-by: NLen Brown <len.brown@intel.com>

turbostat: cpu0: msr offset 0x630 read failed: Input/output error

because Haswell Core does not have C8-C10.

Output C8-C10 only on Haswell ULT.

Fixes: f5a4c76a ("tools/power turbostat: consolidate duplicate model numbers")
Reported-by: NPrarit Bhargava <prarit@redhat.com>
Suggested-by: NKosuke Tatsukawa <tatsu@ab.jp.nec.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Jacobsville behaves like Denverton.
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>