This patch fetch true values of NVME property from FW using New DCMD
interface MR_DCMD_DEV_GET_TARGET_PROP
Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Adding detection logic for NVME device attached behind Ventura
controller.  Driver set HostPageSize in IOC_INIT frame to inform about
page size for NVME devices.  Firmware reports NVME page size to the
driver.  PD INFO DCMD provide new interface type NVME_PD. Driver set
property of NVME device.
Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

With the changes to remove checks for a valid request descriptor,
issue_dcmd will now always return DCMD_SUCCESS. This patch changes
return type of issue_dcmd to void and change all callers appropriately.
Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No functional change. Code clean up. Removing error code which is not
valid scenario.  In megasas_get_request_descriptor we can remove the
error handling which is not required.  With fusion controllers, if there
is a valid message frame available, we are guaranteed to get a
corresponding request descriptor.
Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Moving to use DID_REQUEUE return type for reliable unconditional
retries.  Driver wants unconditional re-queue, so replace DID_RESET with
DID_REQUEUE

Discussed below -
https://www.spinics.net/lists/linux-scsi/msg102848.htmlSigned-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No functional change. Code refactor.

megasas_fire_cmd_fusion can always use 32 bit descriptor write for
ventura. No need to pass extra flag.  Only IOC INIT required 64 bit
Descriptor write.
Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No functional change. Code refactor.

Remove function megasas_fpio_to_ldio as we never require to convert fpio
to ldio because of frame unavailability.  Grab extra frame of raid 1
write fast path before it creates first frame as Fast Path.  Removed
is_raid_1_fp_write flag as raid 1 write fast path command is decided
using r1_alt_dev_handle only.  Move resetting megasas_cmd_fusion fields
at common function megasas_return_cmd_fusion.
Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No functional change. Code refactor.
Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This reverts commit "3e5eadb1" ("scsi: megaraid_sas: Enable or
Disable Fast path based on the PCI Threshold Bandwidth")

This patch was aimed to increase performance of R1 Write operation for
large IO size.  Since this method used timer approach, it turn on/off
fast path did not work as expected.  Patch 0013 describes new algorithm
and performance number.
Signed-off-by: NShivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: NKashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

'conn_info' is malloced in qedi_iscsi_update_conn() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.

Fixes: ace7f46b ("scsi: qedi: Add QLogic FastLinQ offload iSCSI driver framework.")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NManish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Dump host state, power info and host/vendor specific registers
on link failures. This provides useful info to debug the failures.
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Change testbus default config, dump additional testbus registers along
with other debug vendor specific registers. These additional info are
useful in debugging link related failures.
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

UFS clock scaling might start kicking in even before the device
is running at the fastest interface speed which is undesirable.
This change moves the clock scaling kick start only after the
device is detected and running at the fastest interface speed.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently we are suspending clock scaling during clock gating which doesn't
allow us to have clock gating timeout lower than clock scaling polling
window. If clock gating timeout is smaller than the clock scaling polling
window then we will mostly suspend the clock scaling before clock scaling
polling window expires and we might get stuck in same state (scaled down
or scaled up) for quite a long time. And for this reason, we have clock
gating timeout (150ms) greater than clock scaling polling window (100ms).

We would like to have aggressive clock gating timeout even lower than the
clock scaling polling window hence this change is decoupling the clock
scaling suspend/resume from clock gate/ungate. We will not suspend the
clock scaling as part of clock gating instead clock scaling context will
schedule scaling suspend work if there are no more pending transfer
requests.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Whenever some UFS failure occurs the driver prints the UFS
registers in order to help with analysis of the failure.
However this may not be sufficient in some cases, so having
the host controller state as it is represented and managed in
the driver will contribute to analysis efforts.
Added prints of various fields in the hba struct which may be
of interest.
Signed-off-by: NGilad Broner <gbroner@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

UFS driver's load based clock scaling feature scales down the ufs related
clocks in order to allow low power modes of chipsets. UniPro 1.6 supports
maximum gear up to HS-G3 (High Speed Gear3) and some of the chipsets
low power modes may not be allowed in HS-G3 hence this change adds support
to scale gear between HS-G3 and HS-G1 based on same existing load based
clock scaling logic.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Details printed for each request that is aborted can overload the
target as there can be several requests that are aborted at once.
This change will print full request details only for the first
aborted request since the last link reset, and minimal details
for other subsequent requests.
Signed-off-by: NGilad Broner <gbroner@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

On certain error conditions request abort task itself might fail
when aborting a request. In such case, subsequent request aborts
should skip issuing the abort task as it is expected to fail as well,
and device reset handler will be called next.
Signed-off-by: NGilad Broner <gbroner@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Shifting a dma_addr_t right by 32 bits causes a compile-time warning
when that type is only 32 bit wide:

drivers/scsi/aacraid/src.c: In function 'aac_src_start_adapter':
drivers/scsi/aacraid/src.c:414:29: error: right shift count >= width of type [-Werror=shift-count-overflow]

This changes the driver to use the predefined macros consistently,
including one correct but open-coded upper_32_bits() instance.

Fixes: d1ef4da8 ("scsi: aacraid: added support for init_struct_8")
Fixes: 423400e6 ("scsi: aacraid: Include HBA direct interface")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

aac_fib_send can return -ve error returns and hence rcode should be
signed. Currently the rcode >= 0 check is always true and -ve errors are
not being checked.

Thanks to Dan Carpenter for spotting my original broken fix to this
issue.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Signed-off-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NJack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

They are never called and just dispatch to methods of the same names in
the FC and SRP transport classes that are never implemented.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Instead define the timeout behavior purely based on the host_template
eh_timed_out method and wire up the existing transport implementations
in the host templates.  This also clears up the confusion that the
transport template method overrides the host template one, so some
drivers have to re-override the transport template one.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NTyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

EH_NOT_HANDLED is the default case if no eh_timed_out method is
provided, so there is no need to supply it.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

These days we can specify an eh_timed_out handler in the host_template,
so don't have a transport_template definition just for it.

[mkp: fixed typo]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update the driver version to 50740
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Change the aacraid driver prefix from 1.2-1 to 1.2.1
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added new copyright messages
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added a new ioctl interface to retrieve the host device information.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added a new ioctl interface to trigger an IOP or IWBR reset from ioctl.
Primary used by management utility to trigger resets.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added a new IWBR soft reset type, reworked the IOP reset interface for
a bit.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds support to retrieve the unique identifier data (VPD page
83 type3) for Logical drives created on SmartIOC 2000 products. In
addition  added a sysfs device structure to expose the id information.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added task management command support to abort any timed out commands
in case of a eh_abort call and to reset lun's in case of eh_reset call.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added support to send out task management commands.

[mkp: removed // fibsize... ]
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added support to send direct pasthru srb commands from management utilty
to the  controller.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added support for drive hotplug add and removal
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added support to set qd of drives in slave_configure.This only works for
HBA1000 attached drives.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Retrieved queue depth from fw and saved it for future use.
Only applicable for HBA1000 drives.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NDave Carroll <David.Carroll@microsemi.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>