This patch moves SKB allocation for RX packets from current
place i.e. after reading MP regs to place where we already
have read data from SDIO bus ie after cmd53.

mp_rx_aggr_setup has been modified accordingly to set
skb_arr to NULL.
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NShengzhen Li <szli@marvell.com>
Reviewed-by: NAmitkumar Karwar <akarwar@marvell.com>
Reviewed-by: NCathy Luo <cluo@marvell.com>
Reviewed-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch brings in support for SDIO single port rx aggregation
to mwifiex.
Maximum read size support by SDIO cmd53 is 64K.
Based on multi port aggregation which is already part of mwifiex, idea here
is multiple packets received in FW can be aggregated into single buffer.
A separate upload type is defined for such packet aggregated to single port.
Packets from this single buffer are later deaggregated into individual packets.
This way, driver can receive more packets each time through single SDIO cmd53;
thereby reducing no of times MMC bus is accessed.

SDIO SP aggregation support is advertised by FW during load time and driver
would get FW block size in command response of HostCmd_CMD_SDIO_SP_RX_AGGR_CFG.
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Reviewed-by: NAmitkumar Karwar <akarwar@marvell.com>
Reviewed-by: NCathy Luo <cluo@marvell.com>
Reviewed-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

During profiling, we discovered that driver remains idle for time
when pakcet is downloaded to FW but no TX_DONE has been received
i.e. while data_sent is true.

This patch adds enhancement to TX routine where we preprocess
packets from TX queue, make them ready for TX and add them to
separate TX queue.
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NChin-ran Lo <crlo@marvell.com>
Reviewed-by: NCathy Luo <cluo@marvell.com>
Reviewed-by: NAmitkumar Karwar <akarwar@marvell.com>
Reviewed-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch does away with spinlock in
mwifiex_wmm_get_highest_priolist_ptr in order to improve TP.
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch removes BA setup helper routines
mwifiex_is_bastream_setup and  mwifiex_is_amsdu_in_ampdu_allowed.

Current code will use two functions to check bastream setup and
amsdu in ampdu. This patch change these functions to flags, thus
avoiding redundant spin_lock check while dequeuing TX packets.
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Reviewed-by: NCathy Luo <cluo@marvell.com>
Reviewed-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Current code does not check whether main_work_queue or
rx_work_queue is running when preparing to do queue_work,
this code fix add check before calling queue_work, reducing
unnecessary queue_work switch.

This change instead sets more_task flag to ensure we run main_process
superloop once again.
Signed-off-by: NShengzhen Li <szli@marvell.com>
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Reviewed-by: NCathy Luo <cluo@marvell.com>
Reviewed-by: NAmitkumar Karwar <akarwar@marvell.com>
Reviewed-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

SD8897 support buffers of 4K and 16 such ports can be accomodated.
So basically 64K buffer size in single aggregation is supported.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Rename this function to reflect its purpose correctly.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

A crash was detected while changing virtual interface type is in
progress. This was tracked to race condition in accessing bss_priority
table while change is in progress. This patch ensures that main_process
and rx_process works are locked while we change virtual interface.
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We might be in interrupt context at few places. So replace
del_timer_sync() with del_timer(). This patch fixes a kernel
trace problem seen occasionally during our testing.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for auto ARP feature in mwifiex.
The device will respond to ARP requests from the network
with ARP response in suspended state without waking up the host.
This feature is enabled in the driver by default.
Signed-off-by: NMaithili Hinge <maithili@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It's been observed Rx aggregated packets are always followed
by a single Rx packet. This patch improves our logic to add
that extra packet in next aggregation.
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use the built-in function instead of memset.

Miscellanea:

Add #include <linux/etherdevice.h> where appropriate
Use ETH_ALEN instead of 6
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Features which are device specific are already updated in
interface specific initialization e.g. register_dev.
We should not initialize them in mwifiex_init_adapter();
else this would overwrite earlier settings.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Commit 84b313b3 ("mwifiex: make tx packet 64 byte DMA aligned")
induced payload offset issue for USB interface.

There is no USB interface header for tx packets, so there's no need to
pull interface length while processing tx skb.

This patch fixes this issue.
Signed-off-by: NZhaoyang Liu <liuzy@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for DMA alignment of sk_buffs
allocated for RX.
Patch also adds support to modify skb allocation flags.
Signed-off-by: NMarc Yang <yangyang@marvell.com>
Signed-off-by: NQingshui Gao <gaoqs@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

FW crash has been observed while running iperf TX with SD8887
devices. This is because of invalid TX buffer setting. SD8887
supports 2K buffer sizes. This patch fixes this issue.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch changes datatypes for device capability flags to bool.
Patch also aggregates these variables at single place.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes a crash which was happening because of RX of
management frames on uninitialzed interface. Now we drop management
frames for interfaces where cfg80211 has not registered any management
subtype reception or interface has no NL80211 iftype set.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch handles a corner case where TX packet would remain in
driver queue till next packet comes in.
Here is sequence:
1. TX packet is queued via hard_start_xmit and main_work is queued
2. SDIO interrupt comes in which directly call mwifiex_main_process.
This starts executing main superloop.
3. Now work from step1 is scheduled but at first check itself it sees
mwifiex_processing is set and exits.
4. Now if superloop from step2 has passed TX processing part of superloop
this packet would remain in queue until next packet/command/SDIO interrupt
arrives and queues main_work.

This patch fixes this corner case by defining more_task flag which is set when
mwifiex_processing is found to be true. At end of superloop we again check if
more_task flag is set and if set, execute superloop again.
Signed-off-by: NShengzhen Li <szli@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

alloc_workqueue() has string format formation ability e.g. wqname%ifname
will be treated as wqnameifname. Use this and remove string operations
while defining strings for workqueue names.
Reported-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When AP is started, firmware exits power save mode. This
means power save manager of AP takes priority over station.
Firmware stop sending periodic AWAKE events to host.

We may have UAPSD enabled on station which buffers data
packets until AWAKE event from firmware. Data path is
unnecessarily blocked in this case. This patch disables
UAPSD mode to reenable transmit data path.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch makes sure that skb is freed after downloading
NULL packet in error cases. Also, USB chipsets return
-EINPROGRESS after downloading packets, they are freed in
USB completion handler later. We will add missing change
to set tx_lock_flag for USB which blocks further packets.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Memory is leaked after downloading already processed packet. This
patch fixes the problem by freeing returned skb. Other transmit
paths don't have this problem.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Wakeup timer is in sync with 'pm_wakeup_fw_try' flag. It
has been started instead of cancelling at one place. This
patch corrects it.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch enables 11h extensions in FW upon detecting DFS
channel in start radar detection/channel switch handlers.
Patch also takes care of disabling 11h when non DFS channels
are to be set during start_ap handler.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NQingshui Gao <gaoqs@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds cfg80211 channel_switch support for mwifiex.
Upon receiving channel switch request, driver would parse channel
switch announcement IE from beacon_data.
If TX is blocked, netdev queues are stopped. IEs from csa_beacon
are then parsed and set to FW.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NQingshui Gao <gaoqs@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for radar_detected event from FW.
Driver in turn would stop netdev queues to stop TX traffic and
issue RADAR_DETECT event to cfg80211.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NQingshui Gao <gaoqs@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for channel report enabling.
Channel report event happens if radar is detected on specified channel
after driver has issued radar detect command within CAC time.
Driver in turn sends RADAR_DETECTED event to cfg80211 to tell radar was
detected within CAC time.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NQingshui Gao <gaoqs@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support for cfg80211 start_radar_detection handler.
Upon reception of start_radar_detection, driver prepares radar detect
command to FW.

Delayed work is queued for CAC time which sends radar detection finished
event to cfg80211.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NQingshui Gao <gaoqs@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Head & Tail IEs are supposed to be added to beacon and probe response.
This patch adds separate function for parsing head and tail IEs from
cfg80211_beacon_data and sets them to FW.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NQingshui Gao <gaoqs@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Refactor mwifiex_cfg80211_start_ap by creating separate function
to set AP channel and another for configuring other AP parameters
and starting AP.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NQingshui Gao <gaoqs@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch moves IE management routine to end of start_ap handler.
IEs now would be updated after AP has started.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NQingshui Gao <gaoqs@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Store AP configuration in private structure so that we know
current AP configuration.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NQingshui Gao <gaoqs@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When regulatory domain changes, cfg80211 already issues request
to change regulatory domain to driver via reg_notifier.
There is no need to set regulatory again during start_ap.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NQingshui Gao <gaoqs@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently, we support virtual interface type change from
station<=>adhoc or station <=> p2p client/GO.
This patch adds support to change virtual interface type to
any of the type advertised in interface combinations.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch adds support to handle PS events on AP interface as well.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently interface limits are checked by seeing if bss_mode for
particular priv is set. If bss_mode is not set, interface creation
is allowed. This patch adds framework to initializes maximum virtual
interfaces supported during load time and check current number of
interfaces created agains allowed interface limit during new virtual
interface creation.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

FW initialization routine can also be called while changing
virtual interface types.
This patch adds bool parameter "init" to init command routine
so as to differentiate between initialization during driver load
and change virtual interface handler.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This would be used to set mac address while changing virtual
interface to different types.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NCathy Luo <cluo@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>