Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 16 7月, 2015 2 次提交
  3. 12 5月, 2015 1 次提交
  5. 06 5月, 2015 1 次提交
  7. 18 3月, 2015 3 次提交
  9. 10 3月, 2015 1 次提交
  11. 26 1月, 2015 1 次提交
  13. 12 1月, 2015 1 次提交
    • S
      pinctrl: Add driver for Zynq · add958ce
      由 Soren Brinkmann 提交于 
      This adds a pin-control driver for Zynq.

Changes since v2:
- driver-specific DT properties are passed to the core in two arrays,
  one for the actual DT parsing one for the debugfs representation.
  Issue a compiler warning when the number of entries is not the same
  for both arrays.

Changes since v1:
 - fix EMIO_SD1_CD pin name
 - add USB to pinmux options

changes since RFCv2:
 - let Zynq select PINCTRL_ZYNQ. Boot hangs when pinctrl information is
   present in DT but no driver available.
 - add #defines to get rid of magical constants
 - add commas at end of initializers
 - separate changes in mach-zynq in separate patch
 - add driver specific io-standard DT property
 - refactored pinconf set function to not require arguments for
   argument-less properties
 - squash other patches in
   - support for IO-standard property
   - support for low-power mode property
   - migration to pinconf_generic_dt_node_to_map_all()
 - use newly created infrastructure to add pass driver-specific DT
   params to pinconf-generic

changes since RFC:
 - use syscon/regmap to access registers in SLCR space
 - rebase to 3.18: rename enable -> set_mux
 - add kernel-doc
 - support pinconf
   - supported attributes
     - pin-bias: pull up, tristate, disable
     - slew-rate: 0 == slow, 1 == fast; generic pinconf does not display
       argument
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: NAndreas Färber <afaerber@suse.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      add958ce
  15. 11 1月, 2015 1 次提交
  17. 29 10月, 2014 1 次提交
  19. 04 9月, 2014 1 次提交
  21. 02 9月, 2014 1 次提交
  23. 29 8月, 2014 1 次提交
  25. 28 8月, 2014 1 次提交
  27. 11 7月, 2014 6 次提交
  29. 27 5月, 2014 1 次提交
  31. 23 5月, 2014 1 次提交
    • A
      pinctrl: berlin: add the core pinctrl driver for Marvell Berlin SoCs · 3de68d33
      由 Antoine Tenart 提交于 
      The Marvell Berlin boards have a group based pinmuxing mechanism. This
adds the core driver support. We actually do not need any information
about the pins here and only have the definition of the groups.

Let's take the example of the uart0 pinmuxing on the BG2Q. Balls BK4 and
BH6 are muxed to respectively UART0 RX and TX if the group GSM12 is set
to mode 0:

Group	Modes	Offset Base	Offset	LSB	Bit Width
GSM12	3	sm_base		0x40	0x10	0x2

Ball	Group	Mode 0		Mode 1		Mode 2
BK4	GSM12	UART0_RX	IrDA0_RX	GPIO9
BH6	GSM12	UART0_TX	IrDA0_TX	GPIO10

So in order to configure BK4 -> UART0_TX and BH6 -> UART0_RX, we need
to set (sm_base + 0x40 + 0x10) &= ff3fffff.

As pin control registers are part of either chip control or system
control registers, that deal with a bunch of other functions we rely
on a regmap instead of exclusively remapping any resources.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      3de68d33
  33. 04 5月, 2014 1 次提交
  35. 23 4月, 2014 1 次提交
  37. 22 4月, 2014 1 次提交
  39. 14 4月, 2014 1 次提交
  41. 16 1月, 2014 1 次提交
  43. 13 12月, 2013 1 次提交
  45. 06 12月, 2013 2 次提交
  47. 25 11月, 2013 1 次提交
    • D
      pinctrl: pinctrl-imx: add imx25 pinctrl driver · b4a87c9b
      由 Denis Carikli 提交于 
      This is mostly cut and paste from the imx35 pinctrl driver.
The data was generated using sed and awk on
  arch/arm/plat-mxc/include/mach/iomux-mx25.h.

Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: NDenis Carikli <denis@eukrea.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      b4a87c9b
  49. 06 11月, 2013 1 次提交
  51. 29 10月, 2013 2 次提交
  53. 16 10月, 2013 1 次提交
  55. 10 10月, 2013 1 次提交
  57. 19 9月, 2013 1 次提交
    • S
      pinctrl: ADI PIN control driver for the GPIO controller on bf54x and bf60x. · e9a03add
      由 Sonic Zhang 提交于 
      The new ADI GPIO2 controller was introduced since the BF548 and BF60x
processors. It differs a lot from the old one on BF5xx processors. So,
create a pinctrl driver under the pinctrl framework.

- Define gpio ports and pin interrupt controllers as individual platform
  devices.
- Register a pinctrl driver for the whole GPIO ports and pin interrupt
  devices.
- Probe pint devices before port devices. Put device instances into
  the global gpio and pint lists.
- Define peripheral, irq and gpio reservation bit masks for each gpio
  port as runtime resources.
- Save and restore gpio port and pint status MMRs in syscore PM functions.
- Create the plug-in subdrivers to hold the pinctrl soc data for bf54x
  and bf60x. Add soc data into struct adi_pinctrl. Initialize the soc data
  in pin controller probe function. Get the pin groups and functions via
  the soc data reference.
- Call gpiochip_add_pin_range() in gpio device probe function to register
  range cross reference between gpio device and pin control device.
- Get range by pinctrl_find_gpio_range_from_pin(), find gpio_port object
  by container_of() and find adi_pinctrl by pin control device name.
- Handle peripheral and gpio requests in pinctrl operation functions.
- Demux gpio IRQs via the irq_domain created by each GPIO port.

v2-changes:
- Remove unlinke() directive.

v3-changes:
- Rename struct adi_pmx to adi_pinctrl.
- Fix the comments of struct gpio_pint.
- Remove unused pin_base in struct gpio_port.
- Change pint_assign into bool type.
- Add comments about the relationship between pint device and port device
to the driver header.
- Use BIT macro to shift bit.
- Remove all bitmap reservation help functions. Inline reservation functions
into the actual code.
- Remove gpio and offset mutual reference help functions.
- Remove all help functions to find gpio_port and adi_pinctrl structs. Get
range by pinctrl_find_gpio_range_from_pin(), find gpio_port object by
container_of() and find adi_pinctrl by pin control device name.
- Pass bool type usage variable to port_setup help function.
- Separate long bit operations into several lines and add comments.
- Use debugfs to output all GPIO request information.
- Avoid to set drvdata to NULL
- Add explanation to function adi_gpio_init_int()
- Call gpiochip_add_pin_range() in gpio device probe function to register
range cross reference between gpio device and pin control device.
- Remove the reference to pin control device from the gpio_port struct.
Remove the reference list to gpio device from the adi_pinctrl struct.
Replace the global adi_pinctrl list with adi_gpio_port_list. Walk through
the gpio list to do power suspend and resume operations.
- Remove the global GPIO base from struct adi_pinctrl, define pin base in
the platform data for each GPIO port device.
- Initialize adi_pinctrl_setup in arch_initcall().
- print the status of triggers, whether it is in GPIO mode, if it is
flagged to be used as IRQ, etc in adi_pin_dbg_show().
- Create the plug-in subdrivers to hold the pinctrl soc data for bf54x
and bf60x. Add soc data into struct adi_pinctrl. Initialize the soc data
in pin controller probe function. Get the pin groups and functions via
the soc data reference.

v4-changes:
- remove useless system_state checking.
- replace dev_err with dev_warn in both irq and gpio pin cases.
- comment on relationship between irq type and invert operation.
- It is not necessary to check the reservation mode of the requested
pin in IRQ chip operation. Remove the reservation map.
- Use existing gpio/pinctrl subsystem debugfs files. Remove pinctrl-adi2
driver specific debugfs output.
- Add linkport group and function information for bf60x.
- Separate uart and ctsrts pins into 2 groups.
- Separate APAPI and alternative ATAPI pins into 2 groups.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      e9a03add
  59. 15 8月, 2013 1 次提交
    • L
      pinctrl: palmas: add pincontrol driver · 0a8d3e24
      由 Laxman Dewangan 提交于 
      TI Palmas series Power Management IC have multiple pins which can be
configured for different functionality. This pins can be configured
for different function. Also their properties like pull up/down,
open drain enable/disable are configurable.

Add support for pincontrol driver Palmas series device like TPS65913,
TPS80036. The driver supports to be register from DT only.

Changes from V1:
- Add generic property for pins and functions in pinconf-generic.
- Add APIs to map the DT and subnode.
- Move common utils APIs to the pinctrl-utils from this file.
- Update the binding document accordingly.
Changes from V2:
- Add ack by Lee.
- Correct the binding docs.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Acked-by: NLee Jones <lee.jones@linaro.org>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
      0a8d3e24