Add a MAINTAINERS entry for the IBM Power in-Nest Crypto Acceleators
driver.
Signed-off-by: NKent Yoder <key@linux.vnet.ibm.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Support for ESNs (extended sequence numbers).
Tested with strongswan on a P2020RDB back-to-back setup.
Extracted from /etc/ipsec.conf:
esp=aes-sha1-esn-modp4096!
Signed-off-by: NHoria Geanta <horia.geanta@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Generate a link table in case assoc data is a scatterlist.
While at it, add support for handling non-contiguous assoc data and iv.
Signed-off-by: NHoria Geanta <horia.geanta@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

It's more natural to think of these vars as bool rather than int.
Signed-off-by: NHoria Geanta <horia.geanta@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

talitos_edesc_alloc does not need hash_result param.
Checking whether dst scatterlist is NULL or not is all that is required.
Signed-off-by: NHoria Geanta <horia.geanta@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

For IPsec encryption, in the case when:
-the input buffer is fragmented (edesc->src_nents > 0)
-the output buffer is not fragmented (edesc->dst_nents = 0)
the ICV is not output in the link table, but after the encrypted payload.

Copying the ICV must be avoided in this case; consequently the condition
edesc->dma_len > 0 must be more specific, i.e. must depend on the type
of the output buffer - fragmented or not.

Testing was performed by modifying testmgr to support src != dst,
since currently native kernel IPsec does in-place encryption
(src == dst).
Signed-off-by: NHoria Geanta <horia.geanta@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

the entry points and geniv definitions for all aead,
ablkcipher, and hash algorithms are all common; move them to a
single assignment in talitos_alg_alloc().

This assumes it's ok to assign a setkey() on non-hmac algs.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

lighten driver_algs[] by moving them to talitos_alg_alloc().
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Commit bd3c7b5c ("crypto: atmel - add Atmel AES driver") possibly
has a typo error of adding an extra CONFIG_.

CC: Nicolas Royer <nicolas@eukrea.com>
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

devm_kfree and devm_iounmap should not have to be explicitly used.

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x,d;
@@

x = devm_kzalloc(...)
...
?-devm_kfree(d,x);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

virt_to_abs() is just a wrapper around __pa(), use __pa() directly.

We should be including <asm/page.h> to get __pa(). abs_addr.h will be
removed shortly so drop that.

We were getting of.h via abs_addr.h so we need to include that directly.

Having done all that, clean up the ordering of the includes.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Acked-by: NSeth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

crypto: aesni_intel - improve lrw and xts performance by utilizing parallel AES-NI hardware pipelines

Use parallel LRW and XTS encryption facilities to better utilize AES-NI
hardware pipelines and gain extra performance.

Tcrypt benchmark results (async), old vs new ratios:

Intel Core i5-2450M CPU (fam: 6, model: 42, step: 7)

aes:128bit
        lrw:256bit      xts:256bit
size    lrw-enc lrw-dec xts-dec xts-dec
16B     0.99x   1.00x   1.22x   1.19x
64B     1.38x   1.50x   1.58x   1.61x
256B    2.04x   2.02x   2.27x   2.29x
1024B   2.56x   2.54x   2.89x   2.92x
8192B   2.85x   2.99x   3.40x   3.23x

aes:192bit
        lrw:320bit      xts:384bit
size    lrw-enc lrw-dec xts-dec xts-dec
16B     1.08x   1.08x   1.16x   1.17x
64B     1.48x   1.54x   1.59x   1.65x
256B    2.18x   2.17x   2.29x   2.28x
1024B   2.67x   2.67x   2.87x   3.05x
8192B   2.93x   2.84x   3.28x   3.33x

aes:256bit
        lrw:348bit      xts:512bit
size    lrw-enc lrw-dec xts-dec xts-dec
16B     1.07x   1.07x   1.18x   1.19x
64B     1.56x   1.56x   1.70x   1.71x
256B    2.22x   2.24x   2.46x   2.46x
1024B   2.76x   2.77x   3.13x   3.05x
8192B   2.99x   3.05x   3.40x   3.30x

Cc: Huang Ying <ying.huang@intel.com>
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Reviewed-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch add the 842 cryptographic API driver that
submits compression requests to the 842 hardware compression
accelerator driver (nx-compress).

If the hardware accelerator goes offline for any reason
(dynamic disable, migration, etc...), this driver will use LZO
as a software failover for all future compression requests.
For decompression requests, the 842 hardware driver contains
a software implementation of the 842 decompressor to support
the decompression of data that was compressed before the accelerator
went offline.
Signed-off-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NSeth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch adds the driver for interacting with the 842
compression accelerator on IBM Power7+ systems.

The device is a child of the Platform Facilities Option (PFO)
and shows up as a child of the IBM VIO bus.

The compression/decompression API takes the same arguments
as existing compression methods like lzo and deflate.  The 842
hardware operates on 4K hardware pages and the driver breaks up
input on 4K boundaries to submit it to the hardware accelerator.
Signed-off-by: NRobert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: NSeth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch enables compression engine support in the
architecture vector.  This causes the Power hypervisor
to allow access to the nx comrpession accelerator.
Signed-off-by: NSeth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch creates a new submenu for the NX cryptographic
hardware accelerator and breaks the NX options into their own
Kconfig file under drivers/crypto/nx/Kconfig.

This will permit additional NX functionality to be easily
and more cleanly added in the future without touching
drivers/crypto/Makefile|Kconfig.
Signed-off-by: NSeth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

SHARE_WAIT, whilst more optimal for association-less crypto,
has the ability to start thrashing the CCB descriptor/key
caches, given high levels of traffic across multiple security
associations (and thus keys).

Switch to using the SERIAL sharing type, which prefers
the last used CCB for the SA.  On a 2-DECO platform
such as the P3041, this can improve performance by
about 3.7%.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

In some device trees of previous version, there were string "fsl,sec4.0".
To be backward compatible with device trees, we first check "fsl,sec-v4.0",
if it fails, then check for "fsl,sec4.0".
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>

extended to include new hash and rng code, which was omitted from
the previous version of this patch during a rebase of the SDK
version.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

commit "crypto: caam - use non-irq versions of spinlocks for job rings"
made two bad assumptions:

(a) The caam_jr_enqueue lock isn't used in softirq context.
Not true: jr_enqueue can be interrupted by an incoming net
interrupt and the received packet may be sent for encryption,
via caam_jr_enqueue in softirq context, thereby inducing a
deadlock.

This is evidenced when running netperf over an IPSec tunnel
between two P4080's, with spinlock debugging turned on:

[  892.092569] BUG: spinlock lockup on CPU#7, netperf/10634, e8bf5f70
[  892.098747] Call Trace:
[  892.101197] [eff9fc10] [c00084c0] show_stack+0x48/0x15c (unreliable)
[  892.107563] [eff9fc50] [c0239c2c] do_raw_spin_lock+0x16c/0x174
[  892.113399] [eff9fc80] [c0596494] _raw_spin_lock+0x3c/0x50
[  892.118889] [eff9fc90] [c0445e74] caam_jr_enqueue+0xf8/0x250
[  892.124550] [eff9fcd0] [c044a644] aead_decrypt+0x6c/0xc8
[  892.129625] BUG: spinlock lockup on CPU#5, swapper/5/0, e8bf5f70
[  892.129629] Call Trace:
[  892.129637] [effa7c10] [c00084c0] show_stack+0x48/0x15c (unreliable)
[  892.129645] [effa7c50] [c0239c2c] do_raw_spin_lock+0x16c/0x174
[  892.129652] [effa7c80] [c0596494] _raw_spin_lock+0x3c/0x50
[  892.129660] [effa7c90] [c0445e74] caam_jr_enqueue+0xf8/0x250
[  892.129666] [effa7cd0] [c044a644] aead_decrypt+0x6c/0xc8
[  892.129674] [effa7d00] [c0509724] esp_input+0x178/0x334
[  892.129681] [effa7d50] [c0519778] xfrm_input+0x77c/0x818
[  892.129688] [effa7da0] [c050e344] xfrm4_rcv_encap+0x20/0x30
[  892.129697] [effa7db0] [c04b90c8] ip_local_deliver+0x190/0x408
[  892.129703] [effa7de0] [c04b966c] ip_rcv+0x32c/0x898
[  892.129709] [effa7e10] [c048b998] __netif_receive_skb+0x27c/0x4e8
[  892.129715] [effa7e80] [c048d744] netif_receive_skb+0x4c/0x13c
[  892.129726] [effa7eb0] [c03c28ac] _dpa_rx+0x1a8/0x354
[  892.129732] [effa7ef0] [c03c2ac4] ingress_rx_default_dqrr+0x6c/0x108
[  892.129742] [effa7f10] [c0467ae0] qman_poll_dqrr+0x170/0x1d4
[  892.129748] [effa7f40] [c03c153c] dpaa_eth_poll+0x20/0x94
[  892.129754] [effa7f60] [c048dbd0] net_rx_action+0x13c/0x1f4
[  892.129763] [effa7fa0] [c003d1b8] __do_softirq+0x108/0x1b0
[  892.129769] [effa7ff0] [c000df58] call_do_softirq+0x14/0x24
[  892.129775] [ebacfe70] [c0004868] do_softirq+0xd8/0x104
[  892.129780] [ebacfe90] [c003d5a4] irq_exit+0xb8/0xd8
[  892.129786] [ebacfea0] [c0004498] do_IRQ+0xa4/0x1b0
[  892.129792] [ebacfed0] [c000fad8] ret_from_except+0x0/0x18
[  892.129798] [ebacff90] [c0009010] cpu_idle+0x94/0xf0
[  892.129804] [ebacffb0] [c059ff88] start_secondary+0x42c/0x430
[  892.129809] [ebacfff0] [c0001e28] __secondary_start+0x30/0x84
[  892.281474]
[  892.282959] [eff9fd00] [c0509724] esp_input+0x178/0x334
[  892.288186] [eff9fd50] [c0519778] xfrm_input+0x77c/0x818
[  892.293499] [eff9fda0] [c050e344] xfrm4_rcv_encap+0x20/0x30
[  892.299074] [eff9fdb0] [c04b90c8] ip_local_deliver+0x190/0x408
[  892.304907] [eff9fde0] [c04b966c] ip_rcv+0x32c/0x898
[  892.309872] [eff9fe10] [c048b998] __netif_receive_skb+0x27c/0x4e8
[  892.315966] [eff9fe80] [c048d744] netif_receive_skb+0x4c/0x13c
[  892.321803] [eff9feb0] [c03c28ac] _dpa_rx+0x1a8/0x354
[  892.326855] [eff9fef0] [c03c2ac4] ingress_rx_default_dqrr+0x6c/0x108
[  892.333212] [eff9ff10] [c0467ae0] qman_poll_dqrr+0x170/0x1d4
[  892.338872] [eff9ff40] [c03c153c] dpaa_eth_poll+0x20/0x94
[  892.344271] [eff9ff60] [c048dbd0] net_rx_action+0x13c/0x1f4
[  892.349846] [eff9ffa0] [c003d1b8] __do_softirq+0x108/0x1b0
[  892.355338] [eff9fff0] [c000df58] call_do_softirq+0x14/0x24
[  892.360910] [e7169950] [c0004868] do_softirq+0xd8/0x104
[  892.366135] [e7169970] [c003d5a4] irq_exit+0xb8/0xd8
[  892.371101] [e7169980] [c0004498] do_IRQ+0xa4/0x1b0
[  892.375979] [e71699b0] [c000fad8] ret_from_except+0x0/0x18
[  892.381466] [e7169a70] [c0445e74] caam_jr_enqueue+0xf8/0x250
[  892.387127] [e7169ab0] [c044ad4c] aead_givencrypt+0x6ac/0xa70
[  892.392873] [e7169b20] [c050a0b8] esp_output+0x2b4/0x570
[  892.398186] [e7169b80] [c0519b9c] xfrm_output_resume+0x248/0x7c0
[  892.404194] [e7169bb0] [c050e89c] xfrm4_output_finish+0x18/0x28
[  892.410113] [e7169bc0] [c050e8f4] xfrm4_output+0x48/0x98
[  892.415427] [e7169bd0] [c04beac0] ip_local_out+0x48/0x98
[  892.420740] [e7169be0] [c04bec7c] ip_queue_xmit+0x16c/0x490
[  892.426314] [e7169c10] [c04d6128] tcp_transmit_skb+0x35c/0x9a4
[  892.432147] [e7169c70] [c04d6f98] tcp_write_xmit+0x200/0xa04
[  892.437808] [e7169cc0] [c04c8ccc] tcp_sendmsg+0x994/0xcec
[  892.443213] [e7169d40] [c04eebfc] inet_sendmsg+0xd0/0x164
[  892.448617] [e7169d70] [c04792f8] sock_sendmsg+0x8c/0xbc
[  892.453931] [e7169e40] [c047aecc] sys_sendto+0xc0/0xfc
[  892.459069] [e7169f10] [c047b934] sys_socketcall+0x110/0x25c
[  892.464729] [e7169f40] [c000f480] ret_from_syscall+0x0/0x3c

(b) since the caam_jr_dequeue lock is only used in bh context,
then semantically it should use _bh spin_lock types.  spin_lock_bh
semantics are to disable back-halves, and used when a lock is shared
between softirq (bh) context and process and/or h/w IRQ context.
Since the lock is only used within softirq context, and this tasklet
is atomic, there is no need to do the additional work to disable
back halves.

This patch adds back-half disabling protection to caam_jr_enqueue
spin_locks to fix (a), and drops it from caam_jr_dequeue to fix (b).
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch adds a x86_64/avx assembler implementation of the Cast6 block
cipher. The implementation processes eight blocks in parallel (two 4 block
chunk AVX operations). The table-lookups are done in general-purpose registers.
For small blocksizes the functions from the generic module are called. A good
performance increase is provided for blocksizes greater or equal to 128B.

Patch has been tested with tcrypt and automated filesystem tests.

Tcrypt benchmark results:

Intel Core i5-2500 CPU (fam:6, model:42, step:7)

cast6-avx-x86_64 vs. cast6-generic
128bit key:                                             (lrw:256bit)    (xts:256bit)
size    ecb-enc ecb-dec cbc-enc cbc-dec ctr-enc ctr-dec lrw-enc lrw-dec xts-enc xts-dec
16B     0.97x   1.00x   1.01x   1.01x   0.99x   0.97x   0.98x   1.01x   0.96x   0.98x
64B     0.98x   0.99x   1.02x   1.01x   0.99x   1.00x   1.01x   0.99x   1.00x   0.99x
256B    1.77x   1.84x   0.99x   1.85x   1.77x   1.77x   1.70x   1.74x   1.69x   1.72x
1024B   1.93x   1.95x   0.99x   1.96x   1.93x   1.93x   1.84x   1.85x   1.89x   1.87x
8192B   1.91x   1.95x   0.99x   1.97x   1.95x   1.91x   1.86x   1.87x   1.93x   1.90x

256bit key:                                             (lrw:384bit)    (xts:512bit)
size    ecb-enc ecb-dec cbc-enc cbc-dec ctr-enc ctr-dec lrw-enc lrw-dec xts-enc xts-dec
16B     0.97x   0.99x   1.02x   1.01x   0.98x   0.99x   1.00x   1.00x   0.98x   0.98x
64B     0.98x   0.99x   1.01x   1.00x   1.00x   1.00x   1.01x   1.01x   0.97x   1.00x
256B    1.77x   1.83x   1.00x   1.86x   1.79x   1.78x   1.70x   1.76x   1.71x   1.69x
1024B   1.92x   1.95x   0.99x   1.96x   1.93x   1.93x   1.83x   1.86x   1.89x   1.87x
8192B   1.94x   1.95x   0.99x   1.97x   1.95x   1.95x   1.87x   1.87x   1.93x   1.91x
Signed-off-by: NJohannes Goetzfried <Johannes.Goetzfried@informatik.stud.uni-erlangen.de>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

New ECB, CBC, CTR, LRW and XTS testvectors for cast6. We need larger
testvectors to check parallel code paths in the optimized implementation. Tests
have also been added to the tcrypt module.
Signed-off-by: NJohannes Goetzfried <Johannes.Goetzfried@informatik.stud.uni-erlangen.de>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Rename cast6 module to cast6_generic to allow autoloading of optimized
implementations. Generic functions and s-boxes are exported to be able to use
them within optimized implementations.
Signed-off-by: NJohannes Goetzfried <Johannes.Goetzfried@informatik.stud.uni-erlangen.de>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

This patch adds a x86_64/avx assembler implementation of the Cast5 block
cipher. The implementation processes sixteen blocks in parallel (four 4 block
chunk AVX operations). The table-lookups are done in general-purpose registers.
For small blocksizes the functions from the generic module are called. A good
performance increase is provided for blocksizes greater or equal to 128B.

Patch has been tested with tcrypt and automated filesystem tests.

Tcrypt benchmark results:

Intel Core i5-2500 CPU (fam:6, model:42, step:7)

cast5-avx-x86_64 vs. cast5-generic
64bit key:
size    ecb-enc ecb-dec cbc-enc cbc-dec ctr-enc ctr-dec
16B     0.99x   0.99x   1.00x   1.00x   1.02x   1.01x
64B     1.00x   1.00x   0.98x   1.00x   1.01x   1.02x
256B    2.03x   2.01x   0.95x   2.11x   2.12x   2.13x
1024B   2.30x   2.24x   0.95x   2.29x   2.35x   2.35x
8192B   2.31x   2.27x   0.95x   2.31x   2.39x   2.39x

128bit key:
size    ecb-enc ecb-dec cbc-enc cbc-dec ctr-enc ctr-dec
16B     0.99x   0.99x   1.00x   1.00x   1.01x   1.01x
64B     1.00x   1.00x   0.98x   1.01x   1.02x   1.01x
256B    2.17x   2.13x   0.96x   2.19x   2.19x   2.19x
1024B   2.29x   2.32x   0.95x   2.34x   2.37x   2.38x
8192B   2.35x   2.32x   0.95x   2.35x   2.39x   2.39x
Signed-off-by: NJohannes Goetzfried <Johannes.Goetzfried@informatik.stud.uni-erlangen.de>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

New ECB, CBC and CTR testvectors for cast5. We need larger testvectors to check
parallel code paths in the optimized implementation. Tests have also been added
to the tcrypt module.
Signed-off-by: NJohannes Goetzfried <Johannes.Goetzfried@informatik.stud.uni-erlangen.de>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Rename cast5 module to cast5_generic to allow autoloading of optimized
implementations. Generic functions and s-boxes are exported to be able to use
them within optimized implementations.
Signed-off-by: NJohannes Goetzfried <Johannes.Goetzfried@informatik.stud.uni-erlangen.de>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Initialization of cra_list is currently mixed, most ciphers initialize this
field and most shashes do not. Initialization however is not needed at all
since cra_list is initialized/overwritten in __crypto_register_alg() with
list_add(). Therefore perform cleanup to remove all unneeded initializations
of this field in 'arch/s390/crypto/'

Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Initialization of cra_list is currently mixed, most ciphers initialize this
field and most shashes do not. Initialization however is not needed at all
since cra_list is initialized/overwritten in __crypto_register_alg() with
list_add(). Therefore perform cleanup to remove all unneeded initializations
of this field in 'crypto/drivers/'.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-geode@lists.infradead.org
Cc: Michal Ludvig <michal@logix.cz>
Cc: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Cc: Varun Wadekar <vwadekar@nvidia.com>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: NKent Yoder <key@linux.vnet.ibm.com>
Acked-by: NVladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Initialization of cra_list is currently mixed, most ciphers initialize this
field and most shashes do not. Initialization however is not needed at all
since cra_list is initialized/overwritten in __crypto_register_alg() with
list_add(). Therefore perform cleanup to remove all unneeded initializations
of this field in 'arch/x86/crypto/'.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Initialization of cra_list is currently mixed, most ciphers initialize this
field and most shashes do not. Initialization however is not needed at all
since cra_list is initialized/overwritten in __crypto_register_alg() with
list_add(). Therefore perform cleanup to remove all unneeded initializations
of this field in 'crypto/'.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Combine all shash algs to be registered and use new crypto_[un]register_shashes
functions. This simplifies init/exit code.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Combine all shash algs to be registered and use new crypto_[un]register_shashes
functions. This simplifies init/exit code.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Combine all shash algs to be registered and use new crypto_[un]register_shashes
functions. This simplifies init/exit code.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Combine all shash algs to be registered and use new crypto_[un]register_shashes
functions. This simplifies init/exit code.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Add crypto_[un]register_shashes() to allow simplifying init/exit code of shash
crypto modules that register multiple algorithms.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Combine all crypto_alg to be registered and use new crypto_[un]register_algs
functions. This simplifies init/exit code.

Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Combine all crypto_alg to be registered and use new crypto_[un]register_algs
functions. This simplifies init/exit code.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Combine all crypto_alg to be registered and use new crypto_[un]register_algs
functions. This simplifies init/exit code.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Combine all crypto_alg to be registered and use new crypto_[un]register_algs
functions. This simplifies init/exit code.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Combine all crypto_alg to be registered and use new crypto_[un]register_algs
functions. This simplifies init/exit code.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Pull irqdomain changes from Grant Likely:
 "Round of refactoring and enhancements to irq_domain infrastructure.
  This series starts the process of simplifying irqdomain.  The ultimate
  goal is to merge LEGACY, LINEAR and TREE mappings into a single
  system, but had to back off from that after some last minute bugs.
  Instead it mainly reorganizes the code and ensures that the reverse
  map gets populated when the irq is mapped instead of the first time it
  is looked up.

  Merging of the irq_domain types is deferred to v3.7

  In other news, this series adds helpers for creating static mappings
  on a linear or tree mapping."

* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  irqdomain: Improve diagnostics when a domain mapping fails
  irqdomain: eliminate slow-path revmap lookups
  irqdomain: Fix irq_create_direct_mapping() to test irq_domain type.
  irqdomain: Eliminate dedicated radix lookup functions
  irqdomain: Support for static IRQ mapping and association.
  irqdomain: Always update revmap when setting up a virq
  irqdomain: Split disassociating code into separate function
  irq_domain: correct a minor wrong comment for linear revmap
  irq_domain: Standardise legacy/linear domain selection
  irqdomain: Make ops->map hook optional
  irqdomain: Remove unnecessary test for IRQ_DOMAIN_MAP_LEGACY
  irqdomain: Simple NUMA awareness.
  devicetree: add helper inline for retrieving a node's full name