The link between the ethernet MAC and its PHY has become more complex
as the interface evolves.  This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.

Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.

Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.

This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.

Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
  which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
  operating in 1000base-X mode - the ethtool/mii data needs to come
  from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
  which means we need to take ethtool/mii data from the MAC.

Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.

Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal.  By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
  __phylink_ethtool_ksettings_set for it
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an I2C MDIO bus bridge library, to allow phylib to access PHYs which
are connected to an I2C bus instead of the more conventional MDIO bus.
Such PHYs can be found in SFP adapters and SFF modules.

Since PHYs appear at I2C bus address 0x40..0x5f, and 0x50/0x51 are
reserved for SFP EEPROMs/diagnostics, we must not allow the MDIO bus
to access these I2C addresses.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phylink will need phy_start_machine exported, so lets export it as a
GPL symbol.  Documentation/networking/phy.txt indicates that this
should be a PHY API function.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes, we need to do additional work between the PHY coming up and
marking the carrier present - for example, we may need to wait for the
PHY to MAC link to finish negotiation.  This changes phylib to provide
a notification function pointer which avoids the built-in
netif_carrier_on() and netif_carrier_off() functions.

Standard ->adjust_link functionality is provided by hooking a helper
into the new ->phy_link_change method.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the missing 1000Base-X entry to the phy settings table.  This was
not included because the original code could not cope with more than
32 bits of link mode mask.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy_lookup_setting() provides useful functionality in ethtool code
outside phylib.  Move it to phy-core and allow it to be re-used (eg,
in phylink) rather than duplicated elsewhere.  Note that this supports
the larger linkmode space.

As we move the phy settings table, we also need to move the guts of
phy_supported_speeds() as well.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Other code would like to make use of this, so make the speed and duplex
string generation visible, and place it in a separate file.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow the phy settings table to support more than 32 link modes by
switching to the ethtool link mode bit number representation, rather
than storing the mask.  This will allow phylink and other ethtool
code to share the settings table to look up settings.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for GRO (generic receive offload) for aQuantia Atlantic driver.
This results in a perfomance improvement when GRO is enabled.
Signed-off-by: NPavel Belous <pavel.belous@aquantia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rest of the helpers are named tcf_exts_*, so change the name of
the action number helpers to be aligned. While at it, change to inline
functions.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the __udivdi3 undefined error reported by
test robot.

Fixes: b8c17f70 ("net: hns: Add self-adaptive interrupt coalesce support in hns driver")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This was supposed to be a bitwise OR but there is a || vs | typo.

Fixes: 864dc729 ("net: phy: marvell: Refactor m88e1121 RGMII delay configuration")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prepare the datapath for refcounted ubuf_info. Clone ubuf_info with
skb_zerocopy_clone() wherever needed due to skb split, merge, resize
or clone.

Split skb_orphan_frags into two variants. The split, merge, .. paths
support reference counted zerocopy buffers, so do not do a deep copy.
Add skb_orphan_frags_rx for paths that may loop packets to receive
sockets. That is not allowed, as it may cause unbounded latency.
Deep copy all zerocopy copy buffers, ref-counted or not, in this path.

The exact locations to modify were chosen by exhaustively searching
through all code that might modify skb_frag references and/or the
the SKBTX_DEV_ZEROCOPY tx_flags bit.

The changes err on the safe side, in two ways.

(1) legacy ubuf_info paths virtio and tap are not modified. They keep
    a 1:1 ubuf_info to sk_buff relationship. Calls to skb_orphan_frags
    still call skb_copy_ubufs and thus copy frags in this case.

(2) not all copies deep in the stack are addressed yet. skb_shift,
    skb_split and skb_try_coalesce can be refined to avoid copying.
    These are not in the hot path and this patch is hairy enough as
    is, so that is left for future refinement.
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We now have all the necessary IPv6 infrastructure in place, so stop
ignoring these notifications.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without resorting to ACLs, the device performs route lookup solely based
on the destination IP address.

In case source-specific routing is needed, an error is returned and the
abort mechanism is activated, thus allowing the kernel to take over
forwarding decisions.

Instead of aborting, we can trap specific destination prefixes where
source-specific routes are present, but this will result in a lot more
code that is unlikely to ever be used.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case we got a replace event, then the replaced route must exist. If
the route isn't capable of multipath, then replace first matching
non-multipath capable route.

If the route is capable of multipath and matching multipath capable
route is found, then replace it. Otherwise, replace first matching
non-multipath capable route.

The new route is inserted before the replaced one. In case the replaced
route is currently offloaded, then it's overwritten in the device's table
by the new route and later deleted, thus not impacting routed traffic.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow directly connected and remote unicast IPv6 routes to be programmed
to the device's tables.

As with IPv4, identical routes - sharing the same destination prefix -
are ordered in a FIB node according to their table ID and then the
metric. While the kernel doesn't share the same trie for the local and
main table, this does happen in the device, so ordering according to
table ID is needed.

Since individual nexthops can be added and deleted in IPv6, each FIB
entry stores a linked list of the rt6_info structs it represents. Upon
the addition or deletion of a nexthop, a new nexthop group is allocated
according to the new configuration and the old one is destroyed.
Identical groups aren't currently consolidated, but will be in a
follow-up patchset.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We only allow FIB offload in the presence of default rules or an l3mdev
rule. In a similar fashion to IPv4 FIB rules, sanitize IPv6 rules.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FIB notification block currently only handles IPv4 events, but we
want to start handling IPv6 events soon, so lay the groundwork now.

Do that by preparing the work item and process it according to the
notified address family.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As in previous patch, ignore IPv6 notifications since the driver doesn't
support these.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We're about to add IPv6 notifications in the FIB notification chain, but
the driver currently doesn't support these, so ignore them.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FIB notification chain is currently soley used by IPv4 code.
However, we're going to introduce IPv6 FIB offload support, which
requires these notification as well.

As explained in commit c3852ef7 ("ipv4: fib: Replay events when
registering FIB notifier"), upon registration to the chain, the callee
receives a full dump of the FIB tables and rules by traversing all the
net namespaces. The integrity of the dump is ensured by a per-namespace
sequence counter that is incremented whenever a change to the tables or
rules occurs.

In order to allow more address families to use the chain, each family is
expected to register its fib_notifier_ops in its pernet init. These
operations allow the common code to read the family's sequence counter
as well as dump its tables and rules in the given net namespace.

Additionally, a 'family' parameter is added to sent notifications, so
that listeners could distinguish between the different families.

Implement the common code that allows listeners to register to the chain
and for address families to register their fib_notifier_ops. Subsequent
patches will implement these operations in IPv6.

In the future, ipmr and ip6mr will be extended to provide these
notifications as well.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds the support for two related features:

 - Support for TX interrupts, with one interrupt for each CPU

 - Support for different RX queue distribution modes
   MVPP2_QDIST_SINGLE_MODE where a single interrupt, shared by all
   CPUs, receives the RX events, and MVPP2_QDIST_MULTI_MODE, where the
   per-CPU interrupts used for TX events are also used for RX events.

Since additional interrupts are needed, an update to the Device Tree
binding is needed. However, backward compatibility is preserved with
the old Device Tree binding, by gracefully degrading to the original
behavior, with only one RX interrupt, and TX completion being handled
by an hrtimer.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to the introduction of TX interrupts and improved RX
queue distribution, this commit introduces the concept of "queue
vector". A queue vector represents a number of RX and/or TX queues,
and an associated NAPI instance and interrupt.

This commit currently only creates a single queue_vector, so there are
no changes in behavior, but it paves the way for additional
queue_vector in the next commits.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PPv2.2 IP has a concept of "software thread", with all registers
of the PPv2.2 mapped 8 times, for concurrent accesses by 8 "software
threads". In addition, interrupts on RX queues are associated to such
"software thread".

For most cases, we map a "software thread" to the more conventional
concept of CPU, but we will soon have one exception: we will have a
model where we have one TX interrupt per CPU (each using one software
thread), and all RX events mapped to another software thread
(associated to another interrupt).

In preparation for this change, it makes sense to change the naming
from MVPP2_MAX_CPUS to MVPP2_MAX_THREADS, and plan for 8 software
threads instead of 4 currently.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the global variables rxq_number and txq_number hold the
number of per-port TXQs and RXQs. Until now, such numbers were
constant regardless of the driver configuration. As we are going to
introduce different modes for TX and RX queues, these numbers will
depend on the configuration (PPv2.1 vs. PPv2.2, exact queue
distribution logic).

Therefore, as a preparation, we move the number of RXQs and TXQs in
the 'struct mvpp2_port' structure, next to the RXQs and TXQs
descriptor arrays.

For now, they remain initialized to the same default values as
rxq_number/txq_number used to be initialized, but this will change in
future commits.

The only non-mechanical change in this patch is that the check to
verify hardware constraints on the number of RXQs and TXQs is moved
from mvpp2_probe() to mvpp2_port_probe(), since it's now in
mvpp2_port_probe() that we initialize the per-port count of RXQ and
TXQ.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RX queue group allocation is anyway re-done later in
mvpp2_port_init(), so resetting it in mvpp2_init() is not very useful,
and will be annoying as we are going to rework the RX queue group
allocation logic.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MVPP21_ISR_RXQ_GROUP_REG register is not indexed by rxq, but by
port, so we fix the parameter name accordingly. There are no
functional changes.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This operation is required for handling ioctl commands like SIOCGMIIREG,
when debugging MDIO registers from userspace.

This commit adds support for this operation.
Signed-off-by: NRomain Perier <romain.perier@collabora.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the MAINTAINERS file with HNS3 Ethernet driver
maintainers names and other details. This also introduces the new
Makefiles required to build the HNS3 Ethernet driver and updates
the existing Kconfig file in the hisilicon folder.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support of the Ethtool interface to
the HNS3 Ethernet driver. Various commands to read the
statistics, configure the offloading, loopback selftest etc.
are supported.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support of MDIO bus interface for HNS3 driver.
Code provides various interfaces to start and stop the PHY layer
and to read and write the MDIO bus or PHY.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

THis patch adds the support of the Scheduling and Shaping
functionalities during the transmit leg. This also adds the
support of Pause at MAC level. (Pause at per-priority level
shall be added later along with the DCB feature).

Hardware as such consists of two types of cofiguration of 6 level
schedulers. Algorithms varies according to the level and type
of scheduler being used. Current patch is used to initialize
the mapping, algorithms(like SP, DWRR etc) and shaper(CIR, PIR etc)
being used.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NWei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support of Hisilicon Network Subsystem Accceleration
Engine and common operations to access it. This layer provides access to the
hardware configuration, hardware statistics. This layer is also
responsible for triggering the initialization of the PHY layer through
the below MDIO layer.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NWei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support of IMP (Integrated Management Processor)
command interface to the HNS3 driver.

Each PF/VF has support of CQP(Command Queue Pair) ring interface.
Each CQP consis of send queue CSQ and receive queue CRQ.
There are various commands a PF/VF may support, like for Flow Table
manipulation, Device management, Packet buffer allocation, Forwarding,
VLANs config, Tunneling/Overlays etc.

This patch contains code to initialize the command queue, manage the
command queue descriptors and Rx/Tx protocol with the command processor
in the form of various commands/results and acknowledgements.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support of the HNAE3 (Hisilicon Network
Acceleration Engine 3) framework support to the HNS3 driver.

Framework facilitates clients like ENET(HNS3 Ethernet Driver), RoCE
and user-space Ethernet drivers (like ODP etc.) to register with HNAE3
devices and their associated operations.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support of Hisilicon Network Subsystem 3
Ethernet driver to hip08 family of SoCs.

This driver includes basic Rx/Tx functionality. It also includes
the client registration code with the HNAE3(Hisilicon Network
Acceleration Engine 3) framework.

This work provides the initial support to the hip08 SoC and
would incrementally add features or enhancements.
Signed-off-by: NDaode Huang <huangdaode@hisilicon.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NYisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: NWei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement .get_channels (ethtool -l) functionality
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement .get_ringparam (ethtool -g) functionality
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vnic server reports the statistics buffer in big endian format and must
be converted to cpu endian in order to be displayed correctly on little
endian lpars.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>