Fetch actual data from firmware instead of static data
at chip reset time.
Signed-off-by: NQuinn Tran <quinn.tran@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For Dual Mode, Initiator side of the driver finish login,
target side receive PRLI, but driver terminates PRLI.
This patch allows target side to go ahead and accept PRLI.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The logo ELS command allocates dma coherent memory for the
data payload and serialize the completions. When this command
times out, the timeout routine completes the thread waiting
for completion which in turn cleanup resources allocated for
this ELS command processing. Don't call generic sp->free
routine when this ELS command times out to avoid to double
freeing of the same resources.
Signed-off-by: NGiridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add ability to send Implicit PRLO to flush IOs
from FW back to driver.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add option to tell FW to reserve 1/2 of emergency exchanges for ELS.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

For ISP27XX, use shadow register to read FW provided REQQ's consumer
index. The shadow register is dma'ed by firmware.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Enable ATIO Q interrupt handshake for ISP27XX. This patch
coalesce ATIO's interrupts for Quad port ISP27XX adapter.
Interrupt coalesce allows performance to scale for this
specific case.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

DPC thread can stall during switch scan due to slow switch response.
This will stall other work element that needs attention. Moving work
element processing and relogin logic out of DPC thread and into its
own work queue.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replace call to Get Port DataBase MB with PDO_FORCE_ADISC
flag with async ADISC command so driver can see ADISC command
has error or not.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adjusts and reallocates fw_dump memory for target mode
to save for extended login and exchange offload buffers into
dump captured.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

As part of chip reset, all commands from all QPairs are
flushed. This patch fixes code to use Q Pair lock for flush
instead of using old hardware_lock.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Max boundary for exchange off load is 32k exchanges. If a system
is unable to allocate large memory buffer to support this feature,
then driver will reduce the number of exchanges down to a value
system can support.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Current code uses Stop Firmware MB cmd to stop the chip before
driver unload.  This will leave the laser in its current state.
This give the illusion of this adapter is still alive.
For 8G & newer adapters, use chip reset to stop the chip and
bring down the laser.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use IOCB patch to submit Control VP MBX command to reduce
bottle-neck for mbx interface.
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

when processing iocb in a timeout case, driver was trying to log messages
without verifying if the fcport structure could have valid data. This
results in a NULL pointer access.

Fixes: 726b8548("qla2xxx: Add framework for async fabric discovery")
Signed-off-by: NQuinn Tran <quinn.tran@cavium.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

hpsa_show_dev_msg prints other information and a newline after the
message string, so the message string does not need to include a newline
explicitly.  Done using Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NDon Brace <don.brace@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update driver Version to 50877
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Earlier driver would scan throgh all supported buses and targets and add
devices that responded. It would add devices that were _hidden_ by the fw.
Driver would invalidate commands sent to _hidden_ devices via the
AAC_HIDE_DISK check.

Since the driver now adds only the devices that are supposed to be
exposed, this code can be removed.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove unused rescan variable.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is a chance of the driver to be stuck in kdump if drives start
acting up in kdump discovery process and the kernel decides to send eh
resets, which would prompt rescan to be scheduled.

Do not perform a rescan in kdump context, since we do not expect a hotplug
event during kdump and all the devices are going to go away anyway.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add back the ability to scan for hotplug changes while eh was in progress.

Schedule a rescan for a later time in the eh recovery code and wait for
eh to complete in the rescan worker.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If the driver fails to retrieve information from the fw (could happen when
the fw is not fully in its senses), the driver does nothing and change is
not processed correctly by the driver

Schedule host rescan in case of failure. This is only for SAFW, since
the information retrieval failure will happen on SAFW devices.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver uses scsi_scan_host to add new devices in the driver init path,
which adds all the fw exposed devices. The drivers resorts to queue
command checks to block out commands to _hidden_ devices.

Use the hotplug handler code to add new devices during driver init and
other areas, this is only for safw. For ARC scsi_scan_host will still
apply.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently driver will attempt to process hotplug events concurrently based
on the FW interrupt.

Protect safw update function with a scan mutex.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The device hotplug events are processed only after retrieving the updated
lun information from the fw. Does not make sense to keep them separate.

Merge both the hotplug handling and safw adapter setup code into single
function.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Resolve luns checks the if a sdev is already present in the os to figure
out if it needs to be removed. Internally the driver exposes HBA on bus
2 even though its bus 1 in the fw. Its mildly confusing.

Refactor out the sdev lookup into its function to check if sdev has been
added to the kernel or not. Add helper functions to add, remove and put
devices based on their fw bus and target number.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added macros to loop through the MAX SUPPORTED Buses and Targets. This
will make the code a bit easier to read.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The hotplug handler code is duplicated for hba handling and container
handling.

Merged function to handle hba and container hot plug events into the
resolve luns functions. Added a bunch of helper functions to check the
validity of a given target and to check if bus, target is container
device.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Merge aac_get_containers to setup target function, so that information
about all the present devices can be retrieved in one shot.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add helper function to set queue depth from information retrieved from
the bmic phy structure.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Save the bmic information for each phy, so that it can processed in
target setup function.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Created inline function to retrieve lun info for each device from the
phy luns structure.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Move the function to get phy luns information to the top of function
to set target information
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove function call to process targets from the report phy luns function
and make it a function in its own right. This will help understand the
flow of the code.
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add helper function to setup targets devices and create the base for the
upcoming patches
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Rename variables and functions to make bmic identify, report phy luns
to make them consistent across code internal existing code bases
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Edit function that retrieves phy lun information to use common
bmic function
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

safw command submission is duplicated across many functions.

Move the safw submission code from bmic identify into its own function
for common use
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Ideally driver needs to wait for IO to be submitted or responded to before
shutdown.

Move code to wait for IO completion into shutdown path
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Refactored the reset_host store function to make consistent across code
bases
Signed-off-by: NRaghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>