Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 27 5月, 2020 18 次提交
    • T
      nl80211: add KHz frequency offset for most wifi commands · 942ba88b
      由 Thomas Pedersen 提交于 
      cfg80211 recently gained the ability to understand a
frequency offset component in KHz. Expose this in nl80211
through the new attributes NL80211_ATTR_WIPHY_FREQ_OFFSET,
NL80211_FREQUENCY_ATTR_OFFSET,
NL80211_ATTR_CENTER_FREQ1_OFFSET, and
NL80211_BSS_FREQUENCY_OFFSET.

These add support to send and receive a KHz offset
component with the following NL80211 commands:

- NL80211_CMD_FRAME
- NL80211_CMD_GET_SCAN
- NL80211_CMD_AUTHENTICATE
- NL80211_CMD_ASSOCIATE
- NL80211_CMD_CONNECT

Along with any other command which takes a chandef, ie:

- NL80211_CMD_SET_CHANNEL
- NL80211_CMD_SET_WIPHY
- NL80211_CMD_START_AP
- NL80211_CMD_RADAR_DETECT
- NL80211_CMD_NOTIFY_RADAR
- NL80211_CMD_CHANNEL_SWITCH
- NL80211_JOIN_IBSS
- NL80211_CMD_REMAIN_ON_CHANNEL
- NL80211_CMD_JOIN_OCB
- NL80211_CMD_JOIN_MESH
- NL80211_CMD_TDLS_CHANNEL_SWITCH

If the driver advertises a band containing channels with
frequency offset, it must also verify support for
frequency offset channels in its cfg80211 ops, or return
an error.
Signed-off-by: NThomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-3-thomas@adapt-ip.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>
      942ba88b
    • T
      cfg80211: add KHz variants of frame RX API · e76fede8
      由 Thomas Pedersen 提交于 
      Drivers may wish to report the RX frequency in units of
KHz. Provide cfg80211_rx_mgmt_khz() and wrap it with
cfg80211_rx_mgmt() so exisiting drivers which can't report
KHz anyway don't need to change. Add a similar wrapper for
cfg80211_report_obss_beacon() so the frequency units stay
somewhat consistent.

This doesn't actually change the nl80211 API yet.
Signed-off-by: NThomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-2-thomas@adapt-ip.com
[fix mac80211 calling the non-khz version of obss beacon report,
 drop trace point name changes]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
      e76fede8
    • S
      nl80211: simplify peer specific TID configuration · c0336955
      由 Sergey Matyukevich 提交于 
      Current rule for applying TID configuration for specific peer looks overly
complicated. No need to reject new TID configuration when override flag is
specified. Another call with the same TID configuration, but without
override flag, allows to apply new configuration anyway.

Use the same approach as for the 'all peers' case: if override flag is
specified, then reset existing TID configuration and immediately
apply a new one.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-5-sergey.matyukevich.os@quantenna.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>
      c0336955
    • S
      cfg80211: add support for TID specific AMSDU configuration · 33462e68
      由 Sergey Matyukevich 提交于 
      This patch adds support to control per TID MSDU aggregation
using the NL80211_TID_CONFIG_ATTR_AMSDU_CTRL attribute.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-4-sergey.matyukevich.os@quantenna.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>
      33462e68
    • S
      mac80211: fix variable names in TID config methods · 60c2ef0e
      由 Sergey Matyukevich 提交于 
      Fix all variable names from 'tid' to 'tids' to avoid confusion.
Now this is not TID number, but TID mask.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-3-sergey.matyukevich.os@quantenna.comSigned-off-by: NJohannes Berg <johannes.berg@intel.com>
      60c2ef0e
    • A
      net: ethtool: Allow PHY cable test TDR data to configured · f2bc8ad3
      由 Andrew Lunn 提交于 
      Allow the user to configure where on the cable the TDR data should be
retrieved, in terms of first and last sample, and the step between
samples. Also add the ability to ask for TDR data for just one pair.

If this configuration is not provided, it defaults to 1-150m at 1m
intervals for all pairs.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

v3:
Move the TDR configuration into a structure
Add a range check on step
Use NL_SET_ERR_MSG_ATTR() when appropriate
Move TDR configuration into a nest
Document attributes in the request
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f2bc8ad3
    • A
      net: ethtool: Add helpers for cable test TDR data · 6b4a0fc1
      由 Andrew Lunn 提交于 
      Add helpers for returning raw TDR helpers in netlink messages.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6b4a0fc1
    • A
      net: ethtool: Add generic parts of cable test TDR · 1a644de2
      由 Andrew Lunn 提交于 
      Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>

v2
Update nxp-tja11xx for API change.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1a644de2
    • F
      mptcp: attempt coalescing when moving skbs to mptcp rx queue · 4e637c70
      由 Florian Westphal 提交于 
      We can try to coalesce skbs we take from the subflows rx queue with the
tail of the mptcp rx queue.

If successful, the skb head can be discarded early.

We can also free the skb extensions, we do not access them after this.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4e637c70
    • D
      net/smc: mark smc_pnet_policy as const · 09d0310f
      由 Dmitry Vyukov 提交于 
      Netlink policies are generally declared as const.
This is safer and prevents potential bugs.
Signed-off-by: NDmitry Vyukov <dvyukov@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      09d0310f
    • G
      cls_flower: Support filtering on multiple MPLS Label Stack Entries · 61aec25a
      由 Guillaume Nault 提交于 
      With struct flow_dissector_key_mpls now recording the first
FLOW_DIS_MPLS_MAX labels, we can extend Flower to filter on any of
these LSEs independently.

In order to avoid creating new netlink attributes for every possible
depth, let's define a new TCA_FLOWER_KEY_MPLS_OPTS nested attribute
that contains the list of LSEs to match. Each LSE is represented by
another attribute, TCA_FLOWER_KEY_MPLS_OPTS_LSE, which then contains
the attributes representing the depth and the MPLS fields to match at
this depth (label, TTL, etc.).

For each MPLS field, the mask is always set to all-ones, as this is
what the original API did. We could allow user configurable masks in
the future if there is demand for more flexibility.

The new API also allows to only specify an LSE depth. In that case,
Flower only verifies that the MPLS label stack depth is greater or
equal to the provided depth (that is, an LSE exists at this depth).

Filters that only match on one (or more) fields of the first LSE are
dumped using the old netlink attributes, to avoid confusing user space
programs that don't understand the new API.
Signed-off-by: NGuillaume Nault <gnault@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      61aec25a
    • G
      flow_dissector: Parse multiple MPLS Label Stack Entries · 58cff782
      由 Guillaume Nault 提交于 
      The current MPLS dissector only parses the first MPLS Label Stack
Entry (second LSE can be parsed too, but only to set a key_id).

This patch adds the possibility to parse several LSEs by making
__skb_flow_dissect_mpls() return FLOW_DISSECT_RET_PROTO_AGAIN as long
as the Bottom Of Stack bit hasn't been seen, up to a maximum of
FLOW_DIS_MPLS_MAX entries.

FLOW_DIS_MPLS_MAX is arbitrarily set to 7. This should be enough for
many practical purposes, without wasting too much space.

To record the parsed values, flow_dissector_key_mpls is modified to
store an array of stack entries, instead of just the values of the
first one. A bit field, "used_lses", is also added to keep track of
the LSEs that have been set. The objective is to avoid defining a
new FLOW_DISSECTOR_KEY_MPLS_XX for each level of the MPLS stack.

TC flower is adapted for the new struct flow_dissector_key_mpls layout.
Matching on several MPLS Label Stack Entries will be added in the next
patch.

The NFP and MLX5 drivers are also adapted: nfp_flower_compile_mac() and
mlx5's parse_tunnel() now verify that the rule only uses the first LSE
and fail if it doesn't.

Finally, the behaviour of the FLOW_DISSECTOR_KEY_MPLS_ENTROPY key is
slightly modified. Instead of recording the first Entropy Label, it
now records the last one. This shouldn't have any consequences since
there doesn't seem to have any user of FLOW_DISSECTOR_KEY_MPLS_ENTROPY
in the tree. We'd probably better do a hash of all parsed MPLS labels
instead (excluding reserved labels) anyway. That'd give better entropy
and would probably also simplify the code. But that's not the purpose
of this patch, so I'm keeping that as a future possible improvement.
Signed-off-by: NGuillaume Nault <gnault@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      58cff782
    • T
      tipc: add test for Nagle algorithm effectiveness · 0a3e060f
      由 Tuong Lien 提交于 
      When streaming in Nagle mode, we try to bundle small messages from user
as many as possible if there is one outstanding buffer, i.e. not ACK-ed
by the receiving side, which helps boost up the overall throughput. So,
the algorithm's effectiveness really depends on when Nagle ACK comes or
what the specific network latency (RTT) is, compared to the user's
message sending rate.

In a bad case, the user's sending rate is low or the network latency is
small, there will not be many bundles, so making a Nagle ACK or waiting
for it is not meaningful.
For example: a user sends its messages every 100ms and the RTT is 50ms,
then for each messages, we require one Nagle ACK but then there is only
one user message sent without any bundles.

In a better case, even if we have a few bundles (e.g. the RTT = 300ms),
but now the user sends messages in medium size, then there will not be
any difference at all, that says 3 x 1000-byte data messages if bundled
will still result in 3 bundles with MTU = 1500.

When Nagle is ineffective, the delay in user message sending is clearly
wasted instead of sending directly.

Besides, adding Nagle ACKs will consume some processor load on both the
sending and receiving sides.

This commit adds a test on the effectiveness of the Nagle algorithm for
an individual connection in the network on which it actually runs.
Particularly, upon receipt of a Nagle ACK we will compare the number of
bundles in the backlog queue to the number of user messages which would
be sent directly without Nagle. If the ratio is good (e.g. >= 2), Nagle
mode will be kept for further message sending. Otherwise, we will leave
Nagle and put a 'penalty' on the connection, so it will have to spend
more 'one-way' messages before being able to re-enter Nagle.

In addition, the 'ack-required' bit is only set when really needed that
the number of Nagle ACKs will be reduced during Nagle mode.

Testing with benchmark showed that with the patch, there was not much
difference in throughput for small messages since the tool continuously
sends messages without a break, so Nagle would still take in effect.
Acked-by: NYing Xue <ying.xue@windriver.com>
Acked-by: NJon Maloy <jmaloy@redhat.com>
Signed-off-by: NTuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0a3e060f
    • T
      tipc: add support for broadcast rcv stats dumping · 03b6fefd
      由 Tuong Lien 提交于 
      This commit enables dumping the statistics of a broadcast-receiver link
like the traditional 'broadcast-link' one (which is for broadcast-
sender). The link dumping can be triggered via netlink (e.g. the
iproute2/tipc tool) by the link flag - 'TIPC_NLA_LINK_BROADCAST' as the
indicator.

The name of a broadcast-receiver link of a specific peer will be in the
format: 'broadcast-link:<peer-id>'.

For example:

Link <broadcast-link:1001002>
  Window:50 packets
  RX packets:7841 fragments:2408/440 bundles:0/0
  TX packets:0 fragments:0/0 bundles:0/0
  RX naks:0 defs:124 dups:0
  TX naks:21 acks:0 retrans:0
  Congestion link:0  Send queue max:0 avg:0

In addition, the broadcast-receiver link statistics can be reset in the
usual way via netlink by specifying that link name in command.

Note: the 'tipc_link_name_ext()' is removed because the link name can
now be retrieved simply via the 'l->name'.
Acked-by: NYing Xue <ying.xue@windriver.com>
Acked-by: NJon Maloy <jmaloy@redhat.com>
Signed-off-by: NTuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      03b6fefd
    • T
      tipc: enable broadcast retrans via unicast · a91d55d1
      由 Tuong Lien 提交于 
      In some environment, broadcast traffic is suppressed at high rate (i.e.
a kind of bandwidth limit setting). When it is applied, TIPC broadcast
can still run successfully. However, when it comes to a high load, some
packets will be dropped first and TIPC tries to retransmit them but the
packet retransmission is intentionally broadcast too, so making things
worse and not helpful at all.

This commit enables the broadcast retransmission via unicast which only
retransmits packets to the specific peer that has really reported a gap
i.e. not broadcasting to all nodes in the cluster, so will prevent from
being suppressed, and also reduce some overheads on the other peers due
to duplicates, finally improve the overall TIPC broadcast performance.

Note: the functionality can be turned on/off via the sysctl file:

echo 1 > /proc/sys/net/tipc/bc_retruni
echo 0 > /proc/sys/net/tipc/bc_retruni

Default is '0', i.e. the broadcast retransmission still works as usual.
Acked-by: NYing Xue <ying.xue@windriver.com>
Acked-by: NJon Maloy <jmaloy@redhat.com>
Signed-off-by: NTuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      a91d55d1
    • T
      tipc: add back link trace events · c6ed7a5c
      由 Tuong Lien 提交于 
      In the previous commit ("tipc: add Gap ACK blocks support for broadcast
link"), we have removed the following link trace events due to the code
changes:

- tipc_link_bc_ack
- tipc_link_retrans

This commit adds them back along with some minor changes to adapt to
the new code.
Acked-by: NYing Xue <ying.xue@windriver.com>
Acked-by: NJon Maloy <jmaloy@redhat.com>
Signed-off-by: NTuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      c6ed7a5c
    • T
      tipc: introduce Gap ACK blocks for broadcast link · d7626b5a
      由 Tuong Lien 提交于 
      As achieved through commit 9195948f ("tipc: improve TIPC throughput
by Gap ACK blocks"), we apply the same mechanism for the broadcast link
as well. The 'Gap ACK blocks' data field in a 'PROTOCOL/STATE_MSG' will
consist of two parts built for both the broadcast and unicast types:

 31                       16 15                        0
+-------------+-------------+-------------+-------------+
|  bgack_cnt  |  ugack_cnt  |            len            |
+-------------+-------------+-------------+-------------+  -
|            gap            |            ack            |   |
+-------------+-------------+-------------+-------------+    > bc gacks
:                           :                           :   |
+-------------+-------------+-------------+-------------+  -
|            gap            |            ack            |   |
+-------------+-------------+-------------+-------------+    > uc gacks
:                           :                           :   |
+-------------+-------------+-------------+-------------+  -

which is "automatically" backward-compatible.

We also increase the max number of Gap ACK blocks to 128, allowing upto
64 blocks per type (total buffer size = 516 bytes).

Besides, the 'tipc_link_advance_transmq()' function is refactored which
is applicable for both the unicast and broadcast cases now, so some old
functions can be removed and the code is optimized.

With the patch, TIPC broadcast is more robust regardless of packet loss
or disorder, latency, ... in the underlying network. Its performance is
boost up significantly.
For example, experiment with a 5% packet loss rate results:

$ time tipc-pipe --mc --rdm --data_size 123 --data_num 1500000
real    0m 42.46s
user    0m 1.16s
sys     0m 17.67s

Without the patch:

$ time tipc-pipe --mc --rdm --data_size 123 --data_num 1500000
real    8m 27.94s
user    0m 0.55s
sys     0m 2.38s
Acked-by: NYing Xue <ying.xue@windriver.com>
Acked-by: NJon Maloy <jmaloy@redhat.com>
Signed-off-by: NTuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      d7626b5a
    • E
      tcp: tcp_v4_err() icmp skb is named icmp_skb · 23917494
      由 Eric Dumazet 提交于 
      I missed the fact that tcp_v4_err() differs from tcp_v6_err().

After commit 4d1a2d9e ("Rename skb to icmp_skb in tcp_v4_err()")
the skb argument has been renamed to icmp_skb only in one function.

I will in a future patch reconciliate these functions to avoid
this kind of confusion.

Fixes: 45af29ca ("tcp: allow traceroute -Mtcp for unpriv users")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      23917494
  3. 26 5月, 2020 4 次提交
    • S
      batman-adv: Revert "disable ethtool link speed detection when auto negotiation off" · 9ad346c9
      由 Sven Eckelmann 提交于 
      The commit 8c46fcd7 ("batman-adv: disable ethtool link speed detection
when auto negotiation off") disabled the usage of ethtool's link_ksetting
when auto negotation was enabled due to invalid values when used with
tun/tap virtual net_devices. According to the patch, automatic measurements
should be used for these kind of interfaces.

But there are major flaws with this argumentation:

* automatic measurements are not implemented
* auto negotiation has nothing to do with the validity of the retrieved
  values

The first point has to be fixed by a longer patch series. The "validity"
part of the second point must be addressed in the same patch series by
dropping the usage of ethtool's link_ksetting (thus always doing automatic
measurements over ethernet).

Drop the patch again to have more default values for various net_device
types/configurations. The user can still overwrite them using the
batadv_hardif's BATADV_ATTR_THROUGHPUT_OVERRIDE.
Reported-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
      9ad346c9
    • H
      bridge: mrp: Fix out-of-bounds read in br_mrp_parse · 617504c6
      由 Horatiu Vultur 提交于 
      The issue was reported by syzbot. When the function br_mrp_parse was
called with a valid net_bridge_port, the net_bridge was an invalid
pointer. Therefore the check br->stp_enabled could pass/fail
depending where it was pointing in memory.
The fix consists of setting the net_bridge pointer if the port is a
valid pointer.

Reported-by: syzbot+9c6f0f1f8e32223df9a4@syzkaller.appspotmail.com
Fixes: 65369933 ("bridge: mrp: Integrate MRP into the bridge")
Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      617504c6
    • E
      tcp: allow traceroute -Mtcp for unpriv users · 45af29ca
      由 Eric Dumazet 提交于 
      Unpriv users can use traceroute over plain UDP sockets, but not TCP ones.

$ traceroute -Mtcp 8.8.8.8
You do not have enough privileges to use this traceroute method.

$ traceroute -n -Mudp 8.8.8.8
traceroute to 8.8.8.8 (8.8.8.8), 30 hops max, 60 byte packets
 1  192.168.86.1  3.631 ms  3.512 ms  3.405 ms
 2  10.1.10.1  4.183 ms  4.125 ms  4.072 ms
 3  96.120.88.125  20.621 ms  19.462 ms  20.553 ms
 4  96.110.177.65  24.271 ms  25.351 ms  25.250 ms
 5  69.139.199.197  44.492 ms  43.075 ms  44.346 ms
 6  68.86.143.93  27.969 ms  25.184 ms  25.092 ms
 7  96.112.146.18  25.323 ms 96.112.146.22  25.583 ms 96.112.146.26  24.502 ms
 8  72.14.239.204  24.405 ms 74.125.37.224  16.326 ms  17.194 ms
 9  209.85.251.9  18.154 ms 209.85.247.55  14.449 ms 209.85.251.9  26.296 ms^C

We can easily support traceroute over TCP, by queueing an error message
into socket error queue.

Note that applications need to set IP_RECVERR/IPV6_RECVERR option to
enable this feature, and that the error message is only queued
while in SYN_SNT state.

socket(AF_INET6, SOCK_STREAM, IPPROTO_IP) = 3
setsockopt(3, SOL_IPV6, IPV6_RECVERR, [1], 4) = 0
setsockopt(3, SOL_SOCKET, SO_TIMESTAMP_OLD, [1], 4) = 0
setsockopt(3, SOL_IPV6, IPV6_UNICAST_HOPS, [5], 4) = 0
connect(3, {sa_family=AF_INET6, sin6_port=htons(8787), sin6_flowinfo=htonl(0),
        inet_pton(AF_INET6, "2002:a05:6608:297::", &sin6_addr), sin6_scope_id=0}, 28) = -1 EHOSTUNREACH (No route to host)
recvmsg(3, {msg_name={sa_family=AF_INET6, sin6_port=htons(8787), sin6_flowinfo=htonl(0),
        inet_pton(AF_INET6, "2002:a05:6608:297::", &sin6_addr), sin6_scope_id=0},
        msg_namelen=1024->28, msg_iov=[{iov_base="`\r\337\320\0004\6\1&\7\370\260\200\231\16\27\0\0\0\0\0\0\0\0 \2\n\5f\10\2\227"..., iov_len=1024}],
        msg_iovlen=1, msg_control=[{cmsg_len=32, cmsg_level=SOL_SOCKET, cmsg_type=SO_TIMESTAMP_OLD, cmsg_data={tv_sec=1590340680, tv_usec=272424}},
                                   {cmsg_len=60, cmsg_level=SOL_IPV6, cmsg_type=IPV6_RECVERR}],
        msg_controllen=96, msg_flags=MSG_ERRQUEUE}, MSG_ERRQUEUE) = 144

Suggested-by: Maciej Żenczykowski <maze@google.com
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Reviewed-by: NMaciej Żenczykowski <maze@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      45af29ca
    • D
      ipv4: potential underflow in compat_ip_setsockopt() · 6a1015b0
      由 Dan Carpenter 提交于 
      The value of "n" is capped at 0x1ffffff but it checked for negative
values.  I don't think this causes a problem but I'm not certain and
it's harmless to prevent it.

Fixes: 2e041728 ("ipv4: do compat setsockopt for MCAST_MSFILTER directly")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      6a1015b0
  5. 24 5月, 2020 5 次提交
  7. 23 5月, 2020 13 次提交