Relocate the mesh implementation of adding the (extended) supported
rates IE to util.c, anticipating its use by other parts of mac80211.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for sending high-level TDLS commands and TDLS frames via
NL80211_CMD_TDLS_OPER and NL80211_CMD_TDLS_MGMT, respectively. Add
appropriate cfg80211 callbacks for lower level drivers.

Add wiphy capability flags for TDLS support and advertise them via
nl80211.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Cc: Kalyan C Gaddam <chakkal@iit.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, when hostapd sets the station as authorized
we also overwrite its uAPSD parameter. This obviously
leads to buggy behaviour (later, with my patches that
actually add uAPSD support). To fix this, only apply
those parameters if they were actually set in nl80211,
and to achieve that add a bitmap of things to apply.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

tx params are currently configured per hw, although they
should be configured per interface.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever the scan request or tx_mgmt is requesting not to
use CCK rate for managemet frames through
NL80211_ATTR_TX_NO_CCK_RATE attribute, then mac80211 should
select appropriate least non-CCK rate. This could help to
send P2P probes and P2P action frames at non 11b rates
without diabling 11b rates globally.

Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a new nl80211 attribute to specify whether to send the management
frames in CCK rate or not. As of now the wpa_supplicant is disabling
CCK rate at P2P init itself. So this patch helps to send P2P probe
request/probe response/action frames being sent at non CCK rate in 2GHz
without disabling 11b rates.

This attribute is used with NL80211_CMD_TRIGGER_SCAN and
NL80211_CMD_FRAME commands to disable CCK rate for management frame
transmission.

Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Protect 'cb' and 'cb_context' arguments in nci_data_exchange.
In fact, this implements a queue with max length of 1 data
exchange transactions in parallel.
Signed-off-by: NIlan Elias <ilane@ti.com>
Acked-by: NLauro Ramos Venancio <lauro.venancio@openbossa.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.

Update all the drivers that implement these callbacks.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add management interface events for blocking/unblocking a device.
Sender of the block device command gets cmd complete and other
mgmt sockets get the event. Event is also sent to mgmt sockets when
blocking is done with ioctl, e.g when blocking a device with
hciconfig. This makes it possible for bluetoothd to track status
of blocked devices when a third party block or unblocks a device.

Event sending is handled in mgmt_device_blocked function which gets
called from hci_blacklist_add in hci_core.c. A pending command is
added in mgmt_block_device, so that it can found when sending the
event - the event is not sent to the socket from which the pending
command came. Locks were moved out from hci_core.c to hci_sock.c
and mgmt.c, because locking is needed also for mgmt_pending_add in
mgmt.c.
Signed-off-by: NAntti Julku <antti.julku@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The function crypto_blkcipher_setkey() called by smp_e()
can sleep, so all the crypto work has to be moved to
hci_dev workqueue.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The objective is to make the core to have as little as possible
information about SMP procedures and logic. Now, all the SMP
specific information is hidden from the core.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Add command to management interface for enabling/disabling the
fast connectable mode.
Signed-off-by: NAntti Julku <antti.julku@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

One piece of information that was lost when using the mgmt interface,
was the type of the connection. Using HCI events we used to know
the type of the connection based on the type of the event, e.g.
HCI_LE_Connection_Complete for LE links.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Add HCI_CONN_LE_SMP_PEND flag to indicate that SMP is pending
for that connection. This allows to have information that an SMP
procedure is going on for that connection.

We use the HCI_CONN_ENCRYPT_PEND to indicate that encryption
(HCI_LE_Start_Encryption) is pending for that connection.

While a SMP procedure is going on we hold an reference to the
connection, to avoid disconnections.
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This checks if there is any existing connection according to its type
before start iterating in the list and immediately stop iterating when
reaching the number of connections.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The NFC Controller Interface (NCI) is a standard
communication protocol between an NFC Controller (NFCC)
and a Device Host (DH), defined by the NFC Forum.
Signed-off-by: NIlan Elias <ilane@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The file nfc.h was moved from include/net to include/net/nfc,
since new NFC header files will be added to include/net/nfc.
Signed-off-by: NIlan Elias <ilane@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add 2 new nfc control operations:
dev_up to turn on the nfc device
dev_down to turn off the nfc device
Signed-off-by: NIlan Elias <ilane@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NAlexander Simon <an.alexsimon@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the driver (or most likely firmware) decides which AP to use
for roaming based on internal scan result processing, user space
needs to be notified of PMKSA caching candidates to allow RSN
pre-authentication to be used.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add function to find vendor-specific ie (along with
vendor-specific ie struct definition and P2P OUI values)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add/fix some missing docs.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix kernel-doc warning in net/cfg80211.h:

Warning(include/net/cfg80211.h:1884): No description found for parameter 'registered'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set SSID information from nl80211 beacon parameters. Advertise changes
in SSID to low level drivers.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To properly maintain the peer's block ack window, the driver needs to be
able to control the new starting sequence number that is sent along with
the BlockAckReq frame.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Introduce filtering for scheduled scans to reduce the number of
unnecessary results (which cause useless wake-ups).

Add a new nested attribute where sets of parameters to be matched can
be passed when starting a scheduled scan.  Only scan results that
match any of the sets will be returned.

At this point, the set consists of a single parameter, an SSID.  This
can be easily extended in the future to support more complex matches.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

add WIPHY_FLAG_AP_UAPSD flag to indicate uapsd support on
AP mode.

Advertise it to userspace by including a new
NL80211_ATTR_SUPPORT_AP_UAPSD attribute.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When this flag is set, Tx A-MPDU sessions will not be started by
mac80211. This flag is required for devices that support Tx A-MPDU setup
in hardware.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the rssi of the current AP drops, both wpa_supplicant and the
firmware may do a background scan to find a better AP and try to
associate. Since firmware based roaming is faster, inform
wpa_supplicant to avoid roaming and let the firmware decide to
roam if necessary.

For fullmac drivers like ath6kl, it is just enough to provide the
ESSID and the firmware will decide on the BSSID. Since it is not
possible to do pre-auth during roaming for fullmac drivers, the
wpa_supplicant needs to completely disconnect with the old AP and
reconnect with the new AP. This consumes lot of time and it is
better to leave the roaming decision to the firmware.
Signed-off-by: NVivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I will suck out stuff to userspace to start the regulatory
revampamp, this work will be permissively licensed.
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add uapsd_queues and max_sp fields to ieee80211_sta.
These fields might be needed by low-level drivers in
order to configure the AP.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add new NL80211_ATTR_STA_WME nested attribute that contains
wme params needed by the low-level driver (uapsd_queues and
max_sp).

Add these params to the station_parameters struct as well.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can have the NFC core layer allocating the tx head and tail
room for the drivers and avoid 1 or more SKBs copy on write on
the Tx path.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow userspace to set NL80211_MESHCONF_GATE_ANNOUNCEMENTS attribute,
which will advertise this mesh node as being a mesh gate.
NL80211_HWMP_ROOTMODE must be set or this will do nothing.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Allow userspace to set Root Announcement Interval for our mesh
interface. Also, RANN interval is now in proper units of TUs.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch updates the mesh peering frames to the format specified in
the recently ratified 802.11s standard. Several changes took place to
make this happen:

	- Change RX path to handle new self-protected frames
	- Add new Peering management IE
	- Remove old Peer Link IE
	- Remove old plink_action field in ieee80211_mgmt header

These changes by themselves would either break peering, or work by
coincidence, so squash them all into this patch.
Signed-off-by: NThomas Pedersen <thomas@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Do not call ->suspend, ->resume methods after we unregister wiphy. Also
delete sta_clanup timer after we finish wiphy unregister to avoid this:

WARNING: at lib/debugobjects.c:262 debug_print_object+0x85/0xa0()
Hardware name: 6369CTO
ODEBUG: free active (active state 0) object type: timer_list hint: sta_info_cleanup+0x0/0x180 [mac80211]
Modules linked in: aes_i586 aes_generic fuse bridge stp llc autofs4 sunrpc cpufreq_ondemand acpi_cpufreq mperf ext2 dm_mod uinput thinkpad_acpi hwmon sg arc4 rt2800usb rt2800lib crc_ccitt rt2x00usb rt2x00lib mac80211 cfg80211 i2c_i801 iTCO_wdt iTCO_vendor_support e1000e ext4 mbcache jbd2 sd_mod crc_t10dif sr_mod cdrom yenta_socket ahci libahci pata_acpi ata_generic ata_piix i915 drm_kms_helper drm i2c_algo_bit video [last unloaded: microcode]
Pid: 5663, comm: pm-hibernate Not tainted 3.1.0-rc1-wl+ #19
Call Trace:
 [<c0454cfd>] warn_slowpath_common+0x6d/0xa0
 [<c05e05e5>] ? debug_print_object+0x85/0xa0
 [<c05e05e5>] ? debug_print_object+0x85/0xa0
 [<c0454dae>] warn_slowpath_fmt+0x2e/0x30
 [<c05e05e5>] debug_print_object+0x85/0xa0
 [<f8a808e0>] ? sta_info_alloc+0x1a0/0x1a0 [mac80211]
 [<c05e0bd2>] debug_check_no_obj_freed+0xe2/0x180
 [<c051175b>] kfree+0x8b/0x150
 [<f8a126ae>] cfg80211_dev_free+0x7e/0x90 [cfg80211]
 [<f8a13afd>] wiphy_dev_release+0xd/0x10 [cfg80211]
 [<c068d959>] device_release+0x19/0x80
 [<c05d06ba>] kobject_release+0x7a/0x1c0
 [<c07646a8>] ? rtnl_unlock+0x8/0x10
 [<f8a13adb>] ? wiphy_resume+0x6b/0x80 [cfg80211]
 [<c05d0640>] ? kobject_del+0x30/0x30
 [<c05d1a6d>] kref_put+0x2d/0x60
 [<c05d056d>] kobject_put+0x1d/0x50
 [<c08015f4>] ? mutex_lock+0x14/0x40
 [<c068d60f>] put_device+0xf/0x20
 [<c069716a>] dpm_resume+0xca/0x160
 [<c04912bd>] hibernation_snapshot+0xcd/0x260
 [<c04903df>] ? freeze_processes+0x3f/0x90
 [<c049151b>] hibernate+0xcb/0x1e0
 [<c048fdc0>] ? pm_async_store+0x40/0x40
 [<c048fe60>] state_store+0xa0/0xb0
 [<c048fdc0>] ? pm_async_store+0x40/0x40
 [<c05d0200>] kobj_attr_store+0x20/0x30
 [<c0575ea4>] sysfs_write_file+0x94/0xf0
 [<c051e26a>] vfs_write+0x9a/0x160
 [<c0575e10>] ? sysfs_open_file+0x200/0x200
 [<c051e3fd>] sys_write+0x3d/0x70
 [<c080959f>] sysenter_do_call+0x12/0x28

Cc: stable@kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The NL80211_CMD_NEW_BEACON command is, in practice, requesting AP mode
operations to be started. Add new attributes to provide extra IEs
(e.g., WPS IE, P2P IE) for drivers that build Beacon, Probe Response,
and (Re)Association Response frames internally (likely in firmware).
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>