According to the datasheet, the max_register is register 23.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

According to the datasheet, the max_register is 13h.
ARRAY_SIZE(pcm1681_reg_defaults) + 1 is 18 which is wrong.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

According to the datasheet, the max_register is 13h.
ARRAY_SIZE(pcm1681_reg_defaults) + 1 is 18 which is wrong.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current rcar is using rsnd_is_gen1/gen2() to checking its
IP generation, but it needs data mask.
This patch fixes it up.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The two paths were not connected in the DAPM route causing the associated
routes to be non working and the following warnings printed in the logs:
tlv320aic3x-codec 0-001b: ASoC: mux Right Line1L Mux has no paths
tlv320aic3x-codec 0-001b: ASoC: mux Left Line1R Mux has no paths
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

On imx31 with mc13783 codec the FIQ is not necessary and not enabled
as DMA transfer is available.
Change the probe() function to fail only if both FIQ and DMA are not
available.
Signed-off-by: NPhilippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: NMark Brown <broonie@linaro.org>

Commit b0e0a4d6 ("ASoC: omap: Enable COMPILE_TEST build for DT platforms")
added two incorrect CONFIG_ARCH_ARM dependencies making impossible to select
audio support for Nokia RX-51. Fix this by using correct CONFIG_ARM.
Signed-off-by: NJarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Commit 42810d (ASoC: imx-mc13783: Add audmux settings for mx27pdk) broke
the sound on mx31moboard. Restore back the audmux setting on such boards.
Signed-off-by: NPhilippe Rétornaz <philippe.retornaz@epfl.ch>
Signed-off-by: NMark Brown <broonie@linaro.org>

irq_of_parse_and_map() returns 0 on error, not NO_IRQ.

Fix the following xtensa:allmodconfig build error.

sound/soc/fsl/fsl_ssi.c:705:26: error: 'NO_IRQ' undeclared (first use in this function)
make[4]: *** [sound/soc/fsl/fsl_ssi.o] Error 1

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Grant Likely <grant.likely@linaro.org>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch avoids to dereference the uninitialized data pointer if the
error path is entered before devm_kzalloc is called (or if the allocation
fails). It fixes the following warning:

    sound/soc/fsl/imx-sgtl5000.c: In function 'imx_sgtl5000_probe':
    sound/soc/fsl/imx-sgtl5000.c:175:18: warning: 'data' may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Calling devm_clk_get with any device pointer other than our own confuses
devres. Use clk_get instead. This avoids hitting the following warning in
the imx-sgtl5000 error path:

imx-sgtl5000 sound.12: snd_soc_register_card failed (-517)
platform sound.12: Driver imx-sgtl5000 requests probe deferral
------------[ cut here ]------------
WARNING: CPU: 0 PID: 75 at drivers/base/dd.c:272 driver_probe_device+0x194/0x218()
Modules linked in: snd_soc_sgtl5000(+) snd_soc_imx_sgtl5000 coda snd_soc_imx_audmux imx_sdma snd_soc_fsl_spdif snd_soc_fsl_ssi
CPU: 0 PID: 75 Comm: udevd Not tainted 3.11.0-rc6+ #4682
Backtrace:
[<80010bc4>] (dump_backtrace+0x0/0x10c) from [<80010d60>] (show_stack+0x18/0x1c)
 r6:00000110 r5:00000009 r4:00000000 r3:00000000
[<80010d48>] (show_stack+0x0/0x1c) from [<804f0764>] (dump_stack+0x20/0x28)
[<804f0744>] (dump_stack+0x0/0x28) from [<8001a4a4>] (warn_slowpath_common+0x6c/0x8c)
[<8001a438>] (warn_slowpath_common+0x0/0x8c) from [<8001a4e8>] (warn_slowpath_null+0x24/0x2c)
 r8:7f032000 r7:7f02f93c r6:cf8eaa54 r5:cf8eaa20 r4:80728a0c
[<8001a4c4>] (warn_slowpath_null+0x0/0x2c) from [<80286bdc>] (driver_probe_device+0x194/0x218)
[<80286a48>] (driver_probe_device+0x0/0x218) from [<80286cf4>] (__driver_attach+0x94/0x98)
 r7:00000000 r6:cf8eaa54 r5:7f02f93c r4:cf8eaa20
[<80286c60>] (__driver_attach+0x0/0x98) from [<802851c8>] (bus_for_each_dev+0x5c/0x90)
 r6:80286c60 r5:7f02f93c r4:00000000 r3:cf8ef03c
[<8028516c>] (bus_for_each_dev+0x0/0x90) from [<80286654>] (driver_attach+0x24/0x28)
 r6:806d0424 r5:cf16a580 r4:7f02f93c
[<80286630>] (driver_attach+0x0/0x28) from [<802861e4>] (bus_add_driver+0xdc/0x234)
[<80286108>] (bus_add_driver+0x0/0x234) from [<802871d4>] (driver_register+0x80/0x154)
 r8:7f032000 r7:00000001 r6:7f02fa68 r5:7f02fa74 r4:7f02f93c
[<80287154>] (driver_register+0x0/0x154) from [<8033c278>] (i2c_register_driver+0x34/0xbc)
[<8033c244>] (i2c_register_driver+0x0/0xbc) from [<7f032018>] (sgtl5000_i2c_driver_init+0x18/0x24 [snd_soc_sgtl5000])
 r5:7f02fa74 r4:cfb7ff48
[<7f032000>] (sgtl5000_i2c_driver_init+0x0/0x24 [snd_soc_sgtl5000]) from [<80008738>] (do_one_initcall+0xf4/0x150)
[<80008644>] (do_one_initcall+0x0/0x150) from [<80053f64>] (load_module+0x174c/0x1db4)
[<80052818>] (load_module+0x0/0x1db4) from [<800546ac>] (SyS_init_module+0xe0/0xf4)
[<800545cc>] (SyS_init_module+0x0/0xf4) from [<8000e540>] (ret_fast_syscall+0x0/0x30)
 r6:00005b22 r5:00afed68 r4:00000000
---[ end trace b24c5c3bb145dbdd ]---
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

SNDRV_PCM_FORMAT_S8 isn't supposed to fall through to SNDRV_PCM_FORMAT_S16_LE
Signed-off-by: NValentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This is called from snd_ctl_elem_write() with user supplied data so we
need to add some bounds checking.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

If the user passes an invalid value it leads to an info leak when we
print the error message or it could oops.  This is called with user
supplied data from snd_ctl_elem_write().
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

The ->put() function are called from snd_ctl_elem_write() with user
supplied data.  The limit checks here could underflow leading to a
crash.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org

Currently platform CPU DAI widgets are created in soc_probe_platform and
soc_probe_link_dais. Remove the extra call in soc_probe_link_dais().
Signed-off-by: NLiam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The MC13783 Chip Errata, Rev. 4 says, that depending on SPI clock
and main audio clock speed, the Audio Codec or Stereo DAC do sometimes
not start when programmed to do so. This is due to an internal clock
timing issue related to the loading of the SPI bits into the audio block.

On an i.MX27 based system, this issue lead to switched audio channels under
certain circumstances: RTC + Touch + Audio are used and loaded at startup.

The mentioned workaround of writing registers 40 and 41 two times is implemented
here.
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: NMark Brown <broonie@linaro.org>

it should be *USE*, not *USB*
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The S/PDIF driver needs regmap so select it to make sure it gets
included in the build.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The compatible string of the kirkwood-i2s driver was chosen as
"marvell,mvebu-audio". Using such a compatible string is not a good
idea, since "mvebu" is the name of a large family of SOCs, in which
new, unknown SOCs will be coming in the future. It is therefore
impossible to know what will be evolutions of this hardware block in
the next generations of the SOCs. For this reason, the recommandation
for compatible strings of on-SOCs devices has always been to use the
name of the oldest SOC that has the hardware block. New SOCs that have
an exactly compatible hardware block can reference it using the same
compatible string. See [1], [2] and [3] for various cases were this
suggestion was made, including from Rob Herring, a Device Tree binding
maintainer.

As an example, there are already small differences between current
generations:

 * On Kirkwood, only one interrupt is used for audio.
 * On Dove, two interrupts are used, one for audio data and one for
   error reporting.

In the near future, I'll be adding audio support to Armada 370, which
allows has the same hardware block (but maybe with minor variants).

Therefore, this patch changes the driver to accept
"marvell,kirkwood-audio" and "marvell,dove-audio" as compatible
strings instead of the too-generic "marvell,mvebu-audio". The reason
for the two different compatible strings is the difference in the
number of interrupts used by the two SOCs for audio.

This Device Tree binding has never been part of a Linux kernel stable
release so far, so it can be changed now without breaking backward
compatibility.

[1] http://lists.infradead.org/pipermail/linux-mtd/2012-March/040417.html
[2] http://lists.infradead.org/pipermail/linux-arm-kernel/2013-April/161065.html
[3] http://lists.infradead.org/pipermail/linux-arm-kernel/2012-March/087702.htmlSigned-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

As once the error interrupt is triggered, it can not be cleared.
So, disable it.

No side effect found while testing on sama5d3xek and at91sam9x5ek
boards.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Booting a mx51babbage board with a non-dt kernel leads to the following crash:

Unable to handle kernel NULL pointer dereference at virtual address 0000001c
pgd = 80004000
[0000001c] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.11.0-next-20130903 #287
task: 9f860000 ti: 9f862000 task.ti: 9f862000
PC is at of_get_next_available_child+0x5c/0x68
LR is at of_get_next_available_child+0x1c/0x68
pc : [<8043ea58>]    lr : [<8043ea18>]    psr: 60000193
sp : 9f863d58  ip : 00000000  fp : 9f863d74
r10: 9f89a010  r9 : 9f862000  r8 : 807bb26c
r7 : 80615d5c  r6 : 00000000  r5 : 60000113  r4 : 00000000
r3 : 00000000  r2 : 808770a4  r1 : 00000011  r0 : 60000113
Flags: nZCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
Control: 10c5387d  Table: 90004019  DAC: 00000017
Process swapper/0 (pid: 1, stack limit = 0x9f862240)
Stack: (0x9f863d58 to 0x9f864000)

This is caused by commit 8548a464 (ASoC: imx-audmux: Read default
configuration from devicetree).

In order to fix this, add a check for 'of_id' so that
imx_audmux_parse_dt_defaults() only gets called when a dt kernel is running.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

On a mx28 board, running "aplay -l" and "arecord -l" results in the following:

$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: Playback sgtl5000-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: Capture sgtl5000-1 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

,which is not correct because we got a capture device listed in aplay and a
playback device listed in arecord.

On mx28 there are two serial audio interface ports (SAIF0 and SAIF1) and each
one of them are unidirectional.

Allow to specify a dai link as 'playback_only' or 'capture_only', which suits
well for this case.

After this change we can correctly report the capabilities as follows:

$ aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 0: HiFi Playback sgtl5000-0 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

$ arecord -l
**** List of CAPTURE Hardware Devices ****
card 0: mxssgtl5000 [mxs_sgtl5000], device 1: HiFi Capture sgtl5000-1 []
  Subdevices: 1/1
  Subdevice #0: subdevice #0

Also tested playback and capture on the mx28evk board.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add 'playback_only' and 'capture_only' fields that can be used for specifying
that a dai_link has a unidirectional capability.

The motivation for this is for the cases of systems, such as Freescale MX28,
that has two unidirectional DAIs.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NMark Brown <broonie@linaro.org>
Acked-by: NNicolin Chen <B42378@freescale.com>

The ssm2602 uses regmap for caching not soc-cache, so we need to use
regcache_sync() instead of snd_soc_cache_sync().
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

There is a blank space missing between ':=' and 'imx-spdif.o', thus add it.
Signed-off-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Add wrapping '\n' for dev_dbg() in fsl_spdif.c
Signed-off-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Signed-off-by: NBard Liao <bardliao@realtek.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

We need to make sure that the control's cached value is initialized to the same
value as the control's widget->on_val. Otherwise updates might be lost.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

SND_SOC_FSL_UTILS is only used by PowerPC machines, so let's drop it in the
i.mx case.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NNicolin Chen <b42378@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

The legacy S3C-DMA API required every period of a cyclic buffer to be
queued separately. After conversion of Samsung ASoC to Samsung DMA
wrappers somebody made an assumption that the same is needed for DMA
engine API, which is not true.

In effect, Samsung ASoC DMA code was queuing the whole cyclic buffer
multiple times with a shift of one period per iteration, leading to:
  a) severe memory waste - up to 13x times more DMA transfer descriptors
     are allocated than needed,
  b) possible memory corruption, because further cyclic buffers were out
     of the original buffers, due to the offset.

This patch fixes this problem by making the legacy S3C-DMA API use the
same semantics as DMA engine (the whole cyclic buffer is enqueued at
once) and modifying users of Samsung DMA wrappers in cyclic mode to
behave appropriately.
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMark Brown <broonie@linaro.org>

Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Driver core clears the driver data to NULL after device_release or on probe
failure, so just remove it from here.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch implements a device-tree-only machine driver for Freescale
i.MX series Soc. It works with spdif_transmitter/spdif_receiver and
fsl_spdif.c drivers.
Signed-off-by: NNicolin Chen <b42378@freescale.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch permits the generation of the Kirkwood audio driver which
may be used in the Dove boards.
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Signed-off-by: NMark Brown <broonie@linaro.org>

snd_soc_dapm_new_widgets() works on the ASoC card as a whole not on a specific
DAPM context. The DAPM context that is passed as the parameter is only used to
look up the pointer to the card. This patch updates the signature of
snd_soc_dapm_new_widgets() to take the card directly.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>

Call snd_soc_dapm_new_widgets() before the auto non-connected pins have been
marked as not connected will power the system under the assumption that those
pins are connected. Once the pins have been marked as disconnected the system
there will be an additional power run. This can cause unnecessary power
transitions. Calling snd_soc_dapm_new_widgets() only after the pins have been
marked as non-connected avoids this.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@linaro.org>