The code to prevent a bus suspend if a USB3 port was still in link training
also reacted to USB2 port polling state.
This caused bus suspend to busyloop in some cases.
USB2 polling state is different from USB3, and should not prevent bus
suspend.

Limit the USB3 link training state check to USB3 root hub ports only.
The origial commit went to stable so this need to be applied there as well

Fixes: 2f31a67f ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Added USB serial option driver support for Telit LN940 series cellular
modules. Covering both QMI and MBIM modes.

usb-devices output (0x1900):
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=1900 Rev=03.10
S:  Manufacturer=Telit
S:  Product=Telit LN940 Mobile Broadband
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option

usb-devices output (0x1901):
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 20 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1bc7 ProdID=1901 Rev=03.10
S:  Manufacturer=Telit
S:  Product=Telit LN940 Mobile Broadband
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
Signed-off-by: NJörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Added USB serial option driver support for Fibocom NL668 series cellular
modules. Reserved USB endpoints 4, 5 and 6 for network + ADB interfaces.

usb-devices output (QMI mode)
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1508 ProdID=1001 Rev=03.18
S:  Manufacturer=Nodecom NL668 Modem
S:  Product=Nodecom NL668-CN Modem
S:  SerialNumber=
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)

usb-devices output (ECM mode)
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 17 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1508 ProdID=1001 Rev=03.18
S:  Manufacturer=Nodecom NL668 Modem
S:  Product=Nodecom NL668-CN Modem
S:  SerialNumber=
C:  #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I:  If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:  If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
Signed-off-by: NJörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Added USB serial option driver support for Simcom SIM7500/SIM7600 series
cellular modules exposing MBIM interface (VID 0x1e0e,PID 0x9003)

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 14 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1e0e ProdID=9003 Rev=03.18
S:  Manufacturer=SimTech, Incorporated
S:  Product=SimTech, Incorporated
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 7 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 5 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 6 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
Signed-off-by: NJörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Added USB serial option driver support for GosunCn ZTE WeLink ME3630
series cellular modules for USB modes ECM/NCM and MBIM.

usb-devices output MBIM mode:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=0602 Rev=03.18
S:  Manufacturer=Android
S:  Product=Android
S:  SerialNumber=
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim

usb-devices output ECM/NCM mode:
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=1476 Rev=03.18
S:  Manufacturer=Android
S:  Product=Android
S:  SerialNumber=
C:  #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:  If#= 3 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I:  If#= 4 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
Signed-off-by: NJörgen Storvist <jorgen.storvist@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The HP lt4132 is a rebranded Huawei ME906s-158 LTE modem.

The interface with protocol 0x16 is "CDC ECM & NCM" according to the *.inf
files included with the Windows driver. Attaching the option driver to it
doesn't result in a /dev/ttyUSB* device being created, so I've excluded it.
Note that it is also excluded for corresponding Huawei-branded devices, cf.
commit d544db29 ("USB: support new huawei devices in option.c").

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs=  3
P:  Vendor=03f0 ProdID=a31d Rev=01.02
S:  Manufacturer=HP Inc.
S:  Product=HP lt4132 LTE/HSPA+ 4G Module
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=2mA
I:  If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option
I:  If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=06 Prot=16 Driver=(none)
I:  If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs=  3
P:  Vendor=03f0 ProdID=a31d Rev=01.02
S:  Manufacturer=HP Inc.
S:  Product=HP lt4132 LTE/HSPA+ 4G Module
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 7 Cfg#= 2 Atr=a0 MxPwr=2mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=06 Prot=00 Driver=cdc_ether
I:  If#=0x1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=06 Prot=00 Driver=cdc_ether
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=06 Prot=10 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=13 Driver=option
I:  If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=12 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option
I:  If#=0x6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=1b Driver=option

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=ff MxPS=64 #Cfgs=  3
P:  Vendor=03f0 ProdID=a31d Rev=01.02
S:  Manufacturer=HP Inc.
S:  Product=HP lt4132 LTE/HSPA+ 4G Module
S:  SerialNumber=0123456789ABCDEF
C:  #Ifs= 3 Cfg#= 3 Atr=a0 MxPwr=2mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#=0x2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=06 Prot=14 Driver=option
Signed-off-by: NTore Anderson <tore@fud.no>
Cc: stable@vger.kernel.org
[ johan: drop id defines ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

The CP rings are accounted differently on the new 57500 chips.  There
must be enough CP rings for the sum of RX and TX rings on the new
chips.  The current logic may be over-estimating the RX and TX rings.

The output parameter max_cp should be the maximum NQs capped by
MSIX vectors available for networking in the context of 57500 chips.
The existing code which uses CMPL rings capped by the MSIX vectors
works most of the time but is not always correct.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new 57500 chips have introduced the NQ structure in addition to
the existing CP rings in all chips.  We need to introduce a new
bnxt_nq_rings_in_use().  On legacy chips, the 2 functions are the
same and one will just call the other.  On the new chips, they
refer to the 2 separate ring structures.  The new function is now
called to determine the resource (NQ or CP rings) associated with
MSIX that are in use.

On 57500 chips, the RDMA driver does not use the CP rings so
we don't need to do the subtraction adjustment.

Fixes: 41e8d798 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new 57500 chips use 1 NQ per MSIX vector, whereas legacy chips use
1 CP ring per MSIX vector.  To better unify this, add a resv_irqs
field to struct bnxt_hw_resc.  On legacy chips, we initialize resv_irqs
with resv_cp_rings.  On new chips, we initialize it with the allocated
MSIX resources.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent changes to support the 57500 devices have created this
regression.  The bnxt_hwrm_queue_qportcfg() call was moved to be
called earlier before the RDMA support was determined, causing
the CoS queues configuration to be set before knowing whether RDMA
was supported or not.  Fix it by moving it to the right place right
after RDMA support is determined.

Fixes: 98f04cf0 ("bnxt_en: Check context memory requirements from firmware.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rx_ppp and tx_ppp can be set between 0 and 255, so don't clamp to 1.

Fixes: 6e8814ce ("net/mlx4_en: Fix mixed PFC and Global pause user control requests")
Signed-off-by: NTarick Bedeir <tarick@google.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 624ca9c3.

This commit is completely bogus. The STACR register has two formats, old
and new, depending on the version of the IP block used. There's a pair of
device-tree properties that can be used to specify the format used:

	has-inverted-stacr-oc
	has-new-stacr-staopc

What this commit did was to change the bit definition used with the old
parts to match the new parts. This of course breaks the driver on all
the old ones.

Instead, the author should have set the appropriate properties in the
device-tree for the variant used on his board.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nvmet_rdma_release_rsp() may free the response before using it at error
flow.

Fixes: 8407879c ("nvmet-rdma: fix possible bogus dereference under heavy load")
Signed-off-by: NIsrael Rukshin <israelr@mellanox.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Reviewed-by: NMax Gurtovoy <maxg@mellanox.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Delete operations are seeing NULL pointer references in call_timer_fn.
Tracking these back, the timer appears to be the keep alive timer.

nvme_keep_alive_work() which is tied to the timer that is cancelled
by nvme_stop_keep_alive(), simply starts the keep alive io but doesn't
wait for it's completion. So nvme_stop_keep_alive() only stops a timer
when it's pending. When a keep alive is in flight, there is no timer
running and the nvme_stop_keep_alive() will have no affect on the keep
alive io. Thus, if the io completes successfully, the keep alive timer
will be rescheduled.   In the failure case, delete is called, the
controller state is changed, the nvme_stop_keep_alive() is called while
the io is outstanding, and the delete path continues on. The keep
alive happens to successfully complete before the delete paths mark it
as aborted as part of the queue termination, so the timer is restarted.
The delete paths then tear down the controller, and later on the timer
code fires and the timer entry is now corrupt.

Fix by validating the controller state before rescheduling the keep
alive. Testing with the fix has confirmed the condition above was hit.
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.

tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
  Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
  Fast-mode:     tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.

tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
  Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
  Fast-mode:     tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

- For a repeated START condition, this controller starts data transfer
   immediately after the slave address is written to the TX-FIFO.

 - Once the TX-FIFO empty interrupt is asserted, the controller makes
   a pause even if additional data are written to the TX-FIFO.

Given those circumstances, the data after a repeated START may not be
transferred if the interrupt is asserted while the TX-FIFO is being
filled up. A more reliable way is to append TX data only in the
interrupt handler.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

I was totally screwed up in commit eaba6878 ("i2c: uniphier-f:
fix race condition when IRQ is cleared"). Since that commit, if the
number of read bytes is multiple of the FIFO size (8, 16, 24... bytes),
the STOP condition could be issued twice, depending on the timing.
If this happens, the controller will go wrong, resulting in the timeout
error.

It was more than 3 years ago when I wrote this driver, so my memory
about this hardware was vague. Please let me correct the description
in the commit log of eaba6878.

Clearing the IRQ status on exiting the IRQ handler is absolutely
fine. This controller makes a pause while any IRQ status is asserted.
If the IRQ status is cleared first, the hardware may start the next
transaction before the IRQ handler finishes what it supposed to do.

This partially reverts the bad commit with clear comments so that I
will never repeat this mistake.

I also investigated what is happening at the last moment of the read
mode. The UNIPHIER_FI2C_INT_RF interrupt is asserted a bit earlier
(by half a period of the clock cycle) than UNIPHIER_FI2C_INT_RB.

I consulted a hardware engineer, and I got the following information:

UNIPHIER_FI2C_INT_RF
    asserted at the falling edge of SCL at the 8th bit.

UNIPHIER_FI2C_INT_RB
    asserted at the rising edge of SCL at the 9th (ACK) bit.

In order to avoid calling uniphier_fi2c_stop() twice, check the latter
interrupt. I also commented this because it is obscure hardware internal.

Fixes: eaba6878 ("i2c: uniphier-f: fix race condition when IRQ is cleared")
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

Some AMD based HP laptops have a SMB0001 ACPI device node which does not
define any methods.

This leads to the following error in dmesg:

[    5.222731] cmi: probe of SMB0001:00 failed with error -5

This commit makes acpi_smbus_cmi_add() return -ENODEV instead in this case
silencing the error. In case of a failure of the i2c_add_adapter() call
this commit now propagates the error from that call instead of -EIO.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

According to Intel (R) Axxia TM Lionfish Communication Processor
Peripheral Subsystem Hardware Reference Manual, the AXXIA I2C module
have a programmable Master Wait Timer, which among others, checks the
time between commands send in manual mode. When a timeout (25ms) passes,
TSS bit is set in Master Interrupt Status register and a Stop command is
issued by the hardware.

The axxia_i2c_xfer(), does not properly handle this situation, however.
For each message a separate axxia_i2c_xfer_msg() is called and this
function incorrectly assumes that any interrupt might happen only when
waiting for completion. This is mostly correct but there is one
exception - a master timeout can trigger if enough time has passed
between individual transfers. It will, by definition, happen between
transfers when the interrupts are disabled by the code. If that happens,
the hardware issues Stop command.

The interrupt indicating timeout will not be triggered as soon as we
enable them since the Master Interrupt Status is cleared when master
mode is entered again (which happens before enabling irqs) meaning this
error is lost and the transfer is continued even though the Stop was
issued on the bus. The subsequent operations completes without error but
a bogus value (0xFF in case of read) is read as the client device is
confused because aborted transfer. No error is returned from
master_xfer() making caller believe that a valid value was read.

To fix the problem, the TSS bit (indicating timeout) in Master Interrupt
Status register is checked before each transfer. If it is set, there was
a timeout before this transfer and (as described above) the hardware
already issued Stop command so the transaction should be aborted thus
-ETIMEOUT is returned from the master_xfer() callback. In order to be
sure no timeout was issued we can't just read the status just before
starting new transaction as there will always be a small window of time
(few CPU cycles at best) where this might still happen. For this reason
we have to temporally disable the timer before checking for TSS bit.
Disabling it will, however, clear the TSS bit so in order to preserve
that information, we have to read it in ISR so we have to ensure that
the TSS interrupt is not masked between transfers of one transaction.
There is no need to call bus recovery or controller reinitialization if
that happens so it's skipped.
Signed-off-by: NKrzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: NAlexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>

When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.

The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.

Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.

Fixes: c57529e1 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.

Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.

Fixes: 4607f6d2 ("mlxsw: spectrum_router: Support IPv4 underlay decap")
Signed-off-by: NNir Dotan <nird@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It should never be possible for a user to set a VNI on a FID in case one
is already set. The driver therefore returns an error, but fails to drop
the reference count taken earlier when calling
mlxsw_sp_fid_8021d_lookup().

Drop the reference when this unlikely error is hit.

Fixes: 1c30d183 ("mlxsw: spectrum: Enable VxLAN enslavement to bridges")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible to trigger a warning in mlxsw in case a flood entry which
mlxsw is not aware of is deleted from the VxLAN device. This is because
mlxsw expects to find a singly linked list where the flood entry is
present in.

Fix by removing these warnings for now.

Will re-add them in the next release after we teach mlxsw to ask for a
dump of FDB entries from the VxLAN device, once it is enslaved to a
bridge mlxsw cares about.

Fixes: 6e6030bd ("mlxsw: spectrum_nve: Implement common NVE core")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the network stack calls .send_pkt()/.cancel_pkt() during .release(),
a struct vhost_vsock use-after-free is possible.  This occurs because
.release() does not wait for other CPUs to stop using struct
vhost_vsock.

Switch to an RCU-enabled hashtable (indexed by guest CID) so that
.release() can wait for other CPUs by calling synchronize_rcu().  This
also eliminates vhost_vsock_lock acquisition in the data path so it
could have a positive effect on performance.

This is CVE-2018-14625 "kernel: use-after-free Read in vhost_transport_send_pkt".

Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+bd391451452fb0b93039@syzkaller.appspotmail.com
Reported-by: syzbot+e3e074963495f92a89ed@syzkaller.appspotmail.com
Reported-by: syzbot+d5a0a170c5069658b141@syzkaller.appspotmail.com
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Acked-by: NJason Wang <jasowang@redhat.com>

While ccw_io_helper() seems like intended to be exclusive in a sense that
it is supposed to facilitate I/O for at most one thread at any given
time, there is actually nothing ensuring that threads won't pile up at
vcdev->wait_q. If they do, all threads get woken up and see the status
that belongs to some other request than their own. This can lead to bugs.
For an example see:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1788432

This race normally does not cause any problems. The operations provided
by struct virtio_config_ops are usually invoked in a well defined
sequence, normally don't fail, and are normally used quite infrequent
too.

Yet, if some of the these operations are directly triggered via sysfs
attributes, like in the case described by the referenced bug, userspace
is given an opportunity to force races by increasing the frequency of the
given operations.

Let us fix the problem by ensuring, that for each device, we finish
processing the previous request before starting with a new one.
Signed-off-by: NHalil Pasic <pasic@linux.ibm.com>
Reported-by: NColin Ian King <colin.king@canonical.com>
Cc: stable@vger.kernel.org
Message-Id: <20180925121309.58524-3-pasic@linux.ibm.com>
Signed-off-by: NCornelia Huck <cohuck@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Currently we have a race on vcdev->config in virtio_ccw_get_config() and
in virtio_ccw_set_config().

This normally does not cause problems, as these are usually infrequent
operations. However, for some devices writing to/reading from the config
space can be triggered through sysfs attributes. For these, userspace can
force the race by increasing the frequency.
Signed-off-by: NHalil Pasic <pasic@linux.ibm.com>
Cc: stable@vger.kernel.org
Message-Id: <20180925121309.58524-2-pasic@linux.ibm.com>
Signed-off-by: NCornelia Huck <cohuck@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

If a local process has closed a connected socket and hasn't received a
RST packet yet, then the socket remains in the table until a timeout
expires.

When a vhost_vsock instance is released with the timeout still pending,
the socket is never freed because vhost_vsock has already set the
SOCK_DONE flag.

Check if the close timer is pending and let it close the socket.  This
prevents the race which can leak sockets.
Reported-by: NMaximilian Riemensberger <riemensberger@cadami.net>
Cc: Graham Whaley <graham.whaley@gmail.com>
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

Intel Merrifield has a reduced size of FIFO used in iDMA 32-bit controller,
i.e. 512 bytes instead of 1024.

Fix this by partitioning it as 64 bytes per channel.

Note, in the future we might switch to 'fifo-size' property instead of
hard coded value.

Fixes: 199244d6 ("dmaengine: dw: add support of iDMA 32-bit hardware")
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NVinod Koul <vkoul@kernel.org>

Fix activation helper which would return -ETIMEDOUT even if the last
retry attempt was successful.

Also change the semantics of the retries variable so that it actually
holds the number of retries (rather than tries).

Fixes: d2efbbd1 ("gnss: add driver for sirfstar-based receivers")
Cc: stable <stable@vger.kernel.org>	# 4.19
Signed-off-by: NJohan Hovold <johan@kernel.org>

This patch is trying to fix KE issue due to
"BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198"
reported by Syzkaller scan."

[26364:syz-executor0][name:report8t]BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198
[26364:syz-executor0][name:report&]Read of size 1 at addr ffffff900e44f95f by task syz-executor0/26364
[26364:syz-executor0][name:report&]
[26364:syz-executor0]CPU: 7 PID: 26364 Comm: syz-executor0 Tainted: G W 0
[26364:syz-executor0]Call trace:
[26364:syz-executor0][<ffffff9008095cf8>] dump_bacIctrace+Ox0/0x470
[26364:syz-executor0][<ffffff9008096de0>] show_stack+0x20/0x30
[26364:syz-executor0][<ffffff90089cc9c8>] dump_stack+Oxd8/0x128
[26364:syz-executor0][<ffffff90084edb38>] print_address_description +0x80/0x4a8
[26364:syz-executor0][<ffffff90084ee270>] kasan_report+Ox178/0x390
[26364:syz-executor0][<ffffff90084ee4a0>] _asan_report_loadi_noabort+Ox18/0x20
[26364:syz-executor0][<ffffff9008b092ac>] param_set_kgdboc_var+Ox194/0x198
[26364:syz-executor0][<ffffff900813af64>] param_attr_store+Ox14c/0x270
[26364:syz-executor0][<ffffff90081394c8>] module_attr_store+0x60/0x90
[26364:syz-executor0][<ffffff90086690c0>] sysfs_kl_write+Ox100/0x158
[26364:syz-executor0][<ffffff9008666d84>] kernfs_fop_write+0x27c/0x3a8
[26364:syz-executor0][<ffffff9008508264>] do_loop_readv_writev+0x114/0x1b0
[26364:syz-executor0][<ffffff9008509ac8>] do_readv_writev+0x4f8/0x5e0
[26364:syz-executor0][<ffffff9008509ce4>] vfs_writev+0x7c/Oxb8
[26364:syz-executor0][<ffffff900850ba64>] SyS_writev+Oxcc/0x208
[26364:syz-executor0][<ffffff90080883f0>] elO_svc_naked +0x24/0x28
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]The buggy address belongs to the variable:
[26364:syz-executor0][name:report&] kgdb_tty_line+Ox3f/0x40
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]Memory state around the buggy address:
[26364:syz-executor0] ffffff900e44f800: 00 00 00 00 00 04 fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0] ffffff900e44f880: fa fa fa fa 00 fa fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0]> ffffff900e44f900: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00
[26364:syz-executor0][name:report&]                                       ^
[26364:syz-executor0] ffffff900e44f980: 00 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
[26364:syz-executor0] ffffff900e44fa00: 04 fa fa fa fa fa fa fa 00 fa fa fa fa fa fa fa
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:panic&]Disabling lock debugging due to kernel taint
[26364:syz-executor0]------------[cut here]------------

After checking the source code, we've found there might be an out-of-bounds
access to "config[len - 1]" array when the variable "len" is zero.
Signed-off-by: NMacpaul Lin <macpaul@gmail.com>
Acked-by: NDaniel Thompson <daniel.thompson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.

This is according to xhci 1.1 specification section 4.23.5.2 extra note:

"Software shall ensure that a device is prevented from entering a U-state
 where its worst case exit latency approaches the ESIT."

Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.

Cc: <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.

To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: NShyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: NSandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When unloading the ast driver, a warning message is printed by
drm_mode_config_cleanup() because a reference is still held to one of
the drm_connector structs.

Correct this by calling drm_crtc_force_disable_all() in
ast_fbdev_destroy().
Signed-off-by: NSam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1e613f3c630c7bbc72e04a44b178259b9164d2f6.1543798395.git.sbobroff@linux.ibm.com

A "short" ARS (address range scrub) instructs the platform firmware to
return known errors. In contrast, a "long" ARS instructs platform
firmware to arrange every data address on the DIMM to be read / checked
for poisoned data.

The conversion of the flags in commit d3abaf43 "acpi, nfit: Fix
Address Range Scrub completion tracking", changed the meaning of passing
'0' to acpi_nfit_ars_rescan(). Previously '0' meant "not short", now '0'
is ARS_REQ_SHORT. Pass ARS_REQ_LONG to restore the expected scrub-type
behavior of user-initiated ARS sessions.

Fixes: d3abaf43 ("acpi, nfit: Fix Address Range Scrub completion tracking")
Reported-by: NJacek Zloch <jacek.zloch@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: NDave Jiang <dave.jiang@intel.com>
Reviewed-by: NVishal Verma <vishal.l.verma@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Commit cfe30b87 "libnvdimm, pmem: adjust for section collisions with
'System RAM'" enabled Linux to workaround occasions where platform
firmware arranges for "System RAM" and "Persistent Memory" to collide
within a single section boundary. Unfortunately, as reported in this
issue [1], platform firmware can inflict the same collision between
persistent memory regions.

The approach of interrogating iomem_resource does not work in this
case because platform firmware may merge multiple regions into a single
iomem_resource range. Instead provide a method to interrogate regions
that share the same parent bus.

This is a stop-gap until the core-MM can grow support for hotplug on
sub-section boundaries.

[1]: https://github.com/pmem/ndctl/issues/76

Fixes: cfe30b87 ("libnvdimm, pmem: adjust for section collisions with...")
Cc: <stable@vger.kernel.org>
Reported-by: NPatrick Geary <patrickg@supermicro.com>
Tested-by: NPatrick Geary <patrickg@supermicro.com>
Reviewed-by: NVishal Verma <vishal.l.verma@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: NHui Peng <benquike@gmail.com>
Reported-by: NMathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NHui Peng <benquike@gmail.com>
Signed-off-by: NMathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace vcn_v1_0_stop with vcn_v1_0_set_powergating_state during suspend,
to keep adev->vcn.cur_state update. It will fix VCN S3 hung issue.
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NLeo Liu <leo.liu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The thermal_zone_of_device_ops structure can be const as it is only
passed as the last argument of thermal_zone_of_sensor_register
and the corresponding parameter is declared as const.

Done with the help of Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: NEduardo Valentin <edubezval@gmail.com>

The thermal_zone_of_device_ops structure can be const as it is only
passed as the last argument of devm_thermal_zone_of_sensor_register
and the corresponding parameter is declared as const.

Done with the help of Coccinelle.
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: NDaniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: NEduardo Valentin <edubezval@gmail.com>