Reduce the default acceptable rate of DHCP packets to 128 packets per
second and reduce their priority. This is reasonable given the Spectrum
ASICs are limited to 128 ports at the moment.

These are only the default values. Users will be able to modify them via
devlink-trap.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, IPv4 DHCP packets are trapped during L2 forwarding, which
means that packets might be trapped unnecessarily. Instead, only trap
the DHCP packets that reach the router. Either because they were flooded
to the router port or forwarded to it by the FDB. This is consistent
with the corresponding IPv6 trap.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both packet types are needed for the same reason (multicast snooping),
so associate them with the same trap group.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IGMP trap group will be used for MLD traps in the next patch, so
rename it to "MC_SNOOPING" which is more appropriate.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the new devres variant of register_netdev() in the mtk-star-emac
driver and shrink the code by a couple lines.
Signed-off-by: NBartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the mask argument as it's not used by r8168ep_ocp_read().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All callers read the full 32bit value, therefore the mask argument can
be removed.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtl_eri_read() returns the full 32bit value, therefore there's no
benefit in writing back parts of it only. handle it like the vendor
driver and write the full 32 bit always. Omitting the mask argument
avoids some overhead and makes the code better readable.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove runtime PM usage counter decrement when the
increment function has not been called to keep the
counter balanced.
Signed-off-by: NDinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function mlx4_opreq_action(), pointer "mailbox" is not released,
when mlx4_cmd_box() return and error, causing a memory leak bug.
Fix this issue by going to "out" label, mlx4_free_cmd_mailbox() can
free this pointer.

Fixes: fe6f700d ("net/mlx4_core: Respond to operation request by firmware")
Signed-off-by: NQiushi Wu <wu000273@umn.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vlan_for_each() are required to be called with rtnl_lock taken, otherwise
ASSERT_RTNL() warning will be triggered - which happens now during System
resume from suspend:
  cpsw_suspend()
  |- cpsw_ndo_stop()
    |- __hw_addr_ref_unsync_dev()
      |- cpsw_purge_all_mc()
         |- vlan_for_each()
            |- ASSERT_RTNL();

Hence, fix it by surrounding cpsw_ndo_stop() by rtnl_lock/unlock() calls.

Fixes: 15180eca ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the very end of the MACsec block initialization in the MSCC PHY
driver, the MACsec "protocol mode" is set. This setting should be set
based on the PHY id within the package, as the bank used to access the
register used depends on this. This was not done correctly, and only the
first bank was used leading to the two upper PHYs being unstable when
using the VSC8584. This patch fixes it.

Fixes: 1bbe0ecc ("net: phy: mscc: macsec initialization")
Signed-off-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 14b41a29 ("net: stmmac: Delete txtimer in suspend") was the
first attempt to fix a race between mod_timer() and setup_timer()
during stmmac_resume(). However the issue still exists as the commit
only addressed half of the issue.

Same race can still happen as stmmac_resume() re-attaches interface
way too early - even before hardware is fully initialized.  Worse,
doing so allows network traffic to restart and stmmac_tx_timer_arm()
being called in the middle of stmmac_resume(), which re-init tx timers
in stmmac_init_coalesce().  timer_list will be corrupted and system
crashes as a result of race between mod_timer() and setup_timer().

  systemd--1995    2.... 552950018us : stmmac_suspend: 4994
  ksoftirq-9       0..s2 553123133us : stmmac_tx_timer_arm: 2276
  systemd--1995    0.... 553127896us : stmmac_resume: 5101
  systemd--320     7...2 553132752us : stmmac_tx_timer_arm: 2276
  (sd-exec-1999    5...2 553135204us : stmmac_tx_timer_arm: 2276
  ---------------------------------
  pc : run_timer_softirq+0x468/0x5e0
  lr : run_timer_softirq+0x570/0x5e0
  Call trace:
   run_timer_softirq+0x468/0x5e0
   __do_softirq+0x124/0x398
   irq_exit+0xd8/0xe0
   __handle_domain_irq+0x6c/0xc0
   gic_handle_irq+0x60/0xb0
   el1_irq+0xb8/0x180
   arch_cpu_idle+0x38/0x230
   default_idle_call+0x24/0x3c
   do_idle+0x1e0/0x2b8
   cpu_startup_entry+0x28/0x48
   secondary_start_kernel+0x1b4/0x208

Fix this by deferring netif_device_attach() to the end of
stmmac_resume().
Signed-off-by: NLeon Yu <leoyu@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: NTiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ever since its first commit 0ca7111a ("phy: add AT803x driver") the
PHY ID mask was set to 0xffffffef. It is unclear to me why this mask was
chosen in the first place. Both the AR8031/AR8033 and the AR8035
datasheets mention it is always the given value:
 - for AR8031/AR8033 its 0x004d/0xd074
 - for AR8035 its 0x004d/0xd072

Unfortunately, I don't have a datasheet for the AR8030. Therefore, we
leave its PHY ID mask untouched. For the PHYs mentioned before use the
handy PHY_ID_MATCH_EXACT() macro.

I've tried to contact the author of the initial commit, but received no
answer so far.

Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: NMichael Walle <michael@walle.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix loop variables that are comparing or assigning signed against
unsigned values, mostly by declaring loop counters as unsigned.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver was using rq_last_status where it should have been
using sq_last_status. Fix the string to be using the correct
error reporting variable.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The "ethtool -d" handler reads registers in the ice_regs_dump_list array
and returns read values back to the userspace.

The register offsets PFINT0_ITR* are not valid as per the specification
and reading these causes a "unable to handle kernel paging request" bug
in the driver. Remove these registers from ice_regs_dump_list.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Require the Dynamic Device Personalization (DDP) file to have the same
major version number and the same or older minor number than the firmware
version major and minor, respectively.

Check the OS and NVM package versions before downloading the package.
If the OS package version is not compatible with NVM then return an
appropriate error.

Split the 32-byte segment name into a 28-byte segment name and
a 4-byte Track-ID. Older packages will still work with this change
because no package has a name that will take up more than 28 bytes;
in this case the Track-ID will be 0.

Note that the driver will store the segment name as 32-bytes in the
ice_hw structure, in order to normalize the length of the various
package name strings that it uses.

Also add section ID and structure for the segment metadata section.
Signed-off-by: NVictor Raj <victor.raj@intel.com>
Signed-off-by: NDan Nowlin <dan.nowlin@intel.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if a unicast MAC is set via ndo_set_vf_mac, the PF driver will
set the VF's dflt_lan_addr.addr once some basic checks have passed. The
VF is then reset. During reset the PF driver will attempt to program the
VF's MAC from the dflt_lan_addr.addr field. This fails when the MAC
already exists on the PF's switch.

This is causing the VF to be completely disabled until removing/enabling
any VFs via sysfs.

Fix this by checking if the unicast MAC exists before triggering a VF
reset directly in ndo_set_vf_mac. Also, add a check if the unicast MAC
is set to the same value as before and return 0 if that is the case.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently if the iavf is loaded and a VF link transitions from up to
down to up again a Tx timeout will be triggered. This happens because
Tx/Rx queue interrupts are only enabled when receiving the
VIRTCHNL_OP_CONFIG_MAP_IRQ message, which happens on reset or initial
iavf driver load, but not when bringing link up. This is problematic
because they are disabled on the VIRTCHNL_OP_DISABLE_QUEUES message,
which is part of bringing a VF's link down. However, they are not
enabled on the VIRTCHNL_OP_ENABLE_QUEUES message, which is part of
bringing a VF's link up.

Fix this by re-enabling the VF's Rx and Tx queue interrupts when they
were previously configured. This is done by first checking to make
sure the previous value in QINT_[R|T]QCTL.MSIX_INDX is not 0, which
is used to represent the OICR in the VF's interrupt space. If the
MSIX_INDX is non-zero then enable the interrupt by setting the
QINT_[R|T]CTL.CAUSE_ENA bit to 1.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Rx MDD auto reset message was not being logged because logging occurred
after the VF reset and the VF MDD data was reinitialized.

Log the Rx MDD auto reset message before triggering the VF reset.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

As per the specification, the driver needs to call set_mac_cfg
(opcode 0x0603) to be able to exercise jumbo frames. Call the
function during initialization and the post reset rebuild flow.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable accelerated Receive Flow Steering (aRFS). It is used to steer Rx
flows to a specific queue. This functionality is triggered by the network
stack through ndo_rx_flow_steer and requires Flow Director (ntuple on) to
function.

The fltr_info is used to add/remove/update flow rules in the HW, the
fltr_state is used to determine what to do with the filter with respect
to HW and/or SW, and the flow_id is used in co-ordination with the
network stack.

The work for aRFS is split into two paths: the ndo_rx_flow_steer
operation and the ice_service_task. The former is where the kernel hands
us an Rx SKB among other items to setup aRFS and the latter is where
the driver adds/updates/removes filter rules from HW and updates filter
state.

In the Rx path the following things can happen:
        1. New aRFS entries are added to the hash table and the state is
           set to ICE_ARFS_INACTIVE so the filter can be updated in HW
           by the ice_service_task path.
        2. aRFS entries have their Rx Queue updated if we receive a
           pre-existing flow_id and the filter state is ICE_ARFS_ACTIVE.
           The state is set to ICE_ARFS_INACTIVE so the filter can be
           updated in HW by the ice_service_task path.
        3. aRFS entries marked as ICE_ARFS_TODEL are deleted

In the ice_service_task path the following things can happen:
        1. New aRFS entries marked as ICE_ARFS_INACTIVE are added or
           updated in HW.
           and their state is updated to ICE_ARFS_ACTIVE.
        2. aRFS entries are deleted from HW and their state is updated
           to ICE_ARFS_TODEL.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NMadhu Chittim <madhu.chittim@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Following a reset, Flow Director filters are cleared from the hardware.
Rebuild the filters using the software structures containing the filter
rules.
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Flex-bytes allows for packet matching based on an offset and value. This
is supported via the ethtool user-def option.  It is specified by providing
an offset followed by a 2 byte match value. Offset is measured from the
start of the MAC address.

The following restrictions apply to flex-bytes. The specified offset must
be an even number and be smaller than 0x1fe.

Example usage:

ethtool -N eth0 flow-type tcp4 src-ip 192.168.0.55 dst-ip 172.16.0.55 \
src-port 12 dst-port 13 user-def 0x10ffff action 32
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Extend supported filters to allow for IPv6 filters.

Supported fields are: src-ip, dst-ip, src-port, and dst-port
Supported flow-types are: tcp6, udp6, sctp6, ip6

Example usage:

ethtool -N eth0 flow-type tcp6 src-port 12 dst-port 13 \
src-ip fce0::1:34 dst-ip fce0::1:35 action 32
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Support the addition and deletion of IPv4 filters.

Supported fields are: src-ip, dst-ip, src-port, and dst-port
Supported flow-types are: tcp4, udp4, sctp4, ip4

Example usage:

ethtool -N eth0 flow-type tcp4 src-ip 192.168.0.55 dst-ip 172.16.0.55 \
src-port 16 dst-port 12 action 32
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add functionality for ethtool --show-ntuple, allowing for filters to be
displayed when set functionality is added. Add statistics related to
Flow Director matches and status.
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Flow Director allows for redirection based on ntuple rules. Rules are
programmed using the ethtool set-ntuple interface. Supported actions are
redirect to queue and drop.

Setup the initial framework to process Flow Director filters. Create and
allocate resources to manage and program filters to the hardware. Filters
are processed via a sideband interface; a control VSI is created to manage
communication and process requests through the sideband. Upon allocation of
resources, update the hardware tables to accept perfect filters.
Signed-off-by: NHenry Tieman <henry.w.tieman@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since ME systems do not support SLP_S0 in S0ix state, and S0ix entry
and exit flows may cause errors on them it is best to avoid using
e1000e_s0ix_entry_flow and e1000e_s0ix_exit_flow functions.

This was done by creating a struct of all devices that comes with ME
and by checking if the current device has ME.
Signed-off-by: NVitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit b10effb9 ("e1000e: fix buffer overrun while the I219 is
processing DMA transactions") imposes roughly 30% performance penalty.

The commit log states that "Disabling TSO eliminates performance loss
for TCP traffic without a noticeable impact on CPU performance", so
let's disable TSO by default to regain the loss.

CC: stable <stable@vger.kernel.org>
Fixes: b10effb9 ("e1000e: fix buffer overrun while the I219 is processing DMA transactions")
BugLink: https://bugs.launchpad.net/bugs/1802691Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware may stop working if driver failed to disable ULP mode.

Take the return value of e1000_disable_ulp_lpt_lp() into account, and
pass up the error if it fails.
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

igb device gets runtime suspended when there's no link partner. We can't
get correct speed under that state:
$ cat /sys/class/net/enp3s0/speed
1000

In addition to that, an error can also be spotted in dmesg:
[  385.991957] igb 0000:03:00.0 enp3s0: PCIe link lost

Since device can only be runtime suspended when there's no link partner,
we can skip reading register and let the following logic set speed and
duplex with correct status.

The more generic approach will be wrap get_link_ksettings() with begin()
and complete() callbacks. However, for this particular issue, begin()
calls igb_runtime_resume() , which tries to rtnl_lock() while the lock
is already hold by upper ethtool layer.

So let's take this approach until the igb_runtime_resume() no longer
needs to hold rtnl_lock.

CC: stable <stable@vger.kernel.org>
Suggested-by: NAlexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Enable Tidv register, Report Packet Sent, Report Status and
Ethernet CRC flags not in use.
This patch comes to clean up these flags.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During igc_down(), we call igc_nfc_rule_exit() which traverse the NFC
rule list disabling filters one by one. Later on in igc_down() flow
we issue an hardware reset which also clear all filters.  Since we
already reset the hardware, we don't actually need to disable each
filter manually. In order to simplify the code, this patch removes
igc_nfc_rule() altogether.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes adapter->nfc_rule_lock type from spin_lock to mutex
so we avoid unnecessary busy waiting on lock contention.

A closer look at the execution context of NFC rule API users shows that
all of them run in process context. The API users are: ethtool ops,
igc_configure(), called when interface is brought up by user or reset
workequeue thread, igc_down(), called when interface is brought down,
and igc_remove(), called when driver is unloaded.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

None of igc_disable_nfc_rule() callers actually check its returning
value. A closer look at why this function would fail shows that the
only situation is when we try to delete an Ethertype or MAC filter that
doesn't exist.

That situation is very unlikely so we can change igc_del_etype_filter()
and igc_del_mac_filter() logic to "if the filter doesn't exist, we are
done", and keep the logic in igc_disable_nfc_rule() callers simple.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If we try to overwrite an existing rule with the same filter but
different action, we get EEXIST error as shown below.

$ ethtool -N eth0 flow-type ether dst <MACADDR> action 1 loc 10
$ ethtool -N eth0 flow-type ether dst <MACADDR> action 2 loc 10
rmgr: Cannot insert RX class rule: File exists

The second command is expected to overwrite the previous rule in location
10 and succeed.

This patch fixes igc_ethtool_check_nfc_rule() so it also checks the
rules location. In case they match, the rule under evaluation should not
be considered invalid.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If we have RFC rules in adapter->nfc_rule_list when the IGC driver
is unloaded, all rules are leaked. This patch fixes the issue by
introducing the helper igc_flush_nfc_rules() and calling it in
igc_remove(). It also updates igc_set_features() so is reuses the
new helper instead of re-implementing it.
Signed-off-by: NAndre Guedes <andre.guedes@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>