This centralizes the use of the abort functionality, removes the
unneeded buffer cancel (abort does the same thing), sets up to ignore
launch errors after abort, same as cancel.  We need abort on exit from
freeze mode to avoid having buffers stuck in the busy state, if a user
process happened to complete the send while we were in freeze mode
doing the recovery.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The values passed have never been right for iba 6120 chips, but just
happened to work.  We needed to select the right buffer offset in the
chip (both are in same register), and the total length was wrong also,
but was covered by the rounding up.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Define pkt rcvd 'type' in a way consistent with HW spec and chips.

The hardware considers received packets of type 0 to be expected, and
type 1 to be eager. The driver was calling the ipath_f_put_tid
functions using a variable called 'type' set to 0 for eager and to 1
for expected packets.  Worse, the iba6110 and iba6120 drivers used
those values inconsistently.  This was quite confusing.  Now
everything is consistent with the hardware.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

According to chapter 17.2.8.1.1, QPs start in the migrated state and
should send packets with the M bit set in the BTH.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch fixes a minor bug where the wrong QP was checked for a send
work request that should wait for an RNR timeout.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

This patch fixes a bug introduced when moving some code around for
readability.

Setting the wqe pointer at the end of the function is a NOP since it
isn't used.  Move it back to where it is used.
Signed-off-by: NRalph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

In ipath_query_device(), some of the struct ib_device_attr fields were
not being initialized.
Signed-off-by: NRobert Walsh <robert.walsh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Although our chip supports 4K MTUs, our driver doesn't yet support
this feature, so limit the maximum MTU to 2K until we get support for
4K MTUs implemented.
Signed-off-by: NRobert Walsh <robert.walsh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Recognize IBA 6110 Revision 4: same feature set, etc. as earlier revisions.
Signed-off-by: NDave Olson <dave.olson@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

We currently track various errors, now we enhance that capability by
logging some of them to EEPROM.  We also now log a cumulative "active"
time defined by traffic though the InfiniPath HCA beyond the normal SM
traffic.
Signed-off-by: NMichael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The IPATH_RUNTIME_PBC_REWRITE and the IPATH_RUNTIME_LOOSE_DMA_ALIGN
flags were not ever implemented correctly and did not turn out to be
necessary.  Remove the last vestiges of these flags but mark the spot
with a comment to remind us to not reuse these flags in the interest
of binary compatibility.  The INFINIPATH_XGXS_SUPPRESS_ARMLAUNCH_ERR
bit was also not found to be useful, so it was dropped in the cleanup
as well.
Signed-off-by: NJohn Gregor <john.gregor@qlogic.com>
Signed-off-by: NArthur Jones <arthur.jones@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The new LED blinking interface adds more contention for the
unprotected GPIO pins that were already shared, though not commonly at
the same time.  We add locks to the accesses to these pins so that
Read-Modify-Write is now safe.  Some of these locks are added at
interrupt context, so we shadow the registers which drive and inspect
these pins to avoid the mmio read/writes.  This mitigates the effects
of the locks and hastens us through the interrupt.

Add locking and always use shadows for registers controlling GPIO pins
(ExtCtrl and GPIOout). The use of shadows implies doing less I/O,
which can make I2C operation too fast on some platforms. An explicit
udelay(1) in SCL manipulation fixes that.
Signed-off-by: NMichael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

When we want to find an InfiniPath HCA in a rack of nodes, it is often
expeditious to blink the status LEDs via a userspace /sys file.

A write-only led_override "file" is published per device. Writes to
this file are interpreted as (string form) numbers, and the resulting
value sent to ipath_set_led_override(). The upper eight bits are
interpretted as a 4.4 fixed-point "frequency in Hertz", and the bottom
two 4-bit values are alternately (D0..3, then D4..7) used by the
board-specific LED-setting function to override the normal state.
Signed-off-by: NMichael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Signed-off-by: NBryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

mlx4.h uses struct mutex, so although <linux/mutex.h> seems to be pulled in
indirectly by one of the headers it includes, the right thing to do is
to include <linux/mutex.h> directly.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

mlx4_ib.h uses struct mutex, so although <linux/mutex.h> seems to be
pulled in indirectly by one of the headers it includes, the right
thing is to include <linux/mutex.h> directly.
Signed-off-by: NMichael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

gcc correctly warned:

drivers/infiniband/core/umem.c: In function 'ib_umem_get':
drivers/infiniband/core/umem.c:78: warning: 'ret' may be used uninitialized in this function

Set ret to 0 in case npages == 0 and the loop isn't entered at all.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

A few files had 0xa0 characters in comments.  Remove them so that the 
files are clean ASCII text.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Refactor the ehca changes from commit ed23a727 ("IB: Return "maybe
missed event" hint from ib_req_notify_cq()") so the queue arithmetic
is done in slightly fewer lines.  Also, move the spinlock flags into
the block they're used in.
Signed-off-by: NJoachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Extend the SMI with switch (intermediate hop) support. Care has been
taken to ensure that the CA (and router) code paths are changed as
little as possible.
Signed-off-by: NSuresh Shelvapille <suri@baymicrosystems.com>
Signed-off-by: NHal Rosenstock <halr@voltaire.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (31 commits)
  firewire: fw-sbp2: fix DMA mapping of management ORBs
  firewire: fw-sbp2: fix DMA mapping of command ORBs
  firewire: fw-sbp2: fix DMA mapping of S/G tables
  firewire: fw-sbp2: add a boundary check
  firewire: fw-sbp2: correctly align page tables
  firewire: fw-sbp2: memset wants string.h
  firewire: fw-sbp2: use correct speed in sbp2_agent_reset
  firewire: fw-sbp2: correctly dereference by container_of
  firewire: Document userspace ioctl interface.
  firewire: fw-sbp2: implement nonexclusive login
  firewire: fw-sbp2: let SCSI shutdown commands through before logout
  firewire: fw-sbp2: implement max sectors limit for some old bridges
  firewire: simplify a struct type
  firewire: support S100B...S400B and link slower than PHY
  firewire: optimize gap count with 1394b leaf nodes
  firewire: remove unused macro
  firewire: missing newline in printk
  firewire: fw-sbp2: remove unused struct member
  ieee1394: remove old isochronous ABI
  ieee1394: sbp2: change some module parameters from int to bool
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: handle cases of volume knobs generating relative values
  HID: Logitech keyboard 0xc311 needs reset leds quirk
  HID: support for logitech cordless desktop LX500 special mapping
  HID: fix autocentering of PID devices
  HID: separate quirks for report descriptor fixup
  HID: Add NOGET quirk for all NCR devices
  HID: support for Petalynx Maxter remote control
  HID: fix mismatch between hid-input HUT find/search mapping and the HUT
  HID: support for Gameron dual psx adaptor
  USB HID: avoid flush_scheduled_work()
  HID: Use menuconfig objects
  HID: force hid-input for Microsoft SideWinder GameVoice device
  HID: input mapping for Chicony KU-0418 tactical pad
  HID: make debugging output runtime-configurable

* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (75 commits)
  Ethernet driver for EISA only SNI RM200/RM400 machines
  Extract chip specific code out of lasi_82596.c
  ehea: Whitespace cleanup
  pasemi_mac: Fix TX interrupt threshold
  spidernet: Replace literal with const
  r8169: perform RX config change after mac filtering
  r8169: mac address change support
  r8169: display some extra debug information during startup
  r8169: add endianess annotations to [RT]xDesc
  r8169: align the IP header when there is no DMA constraint
  r8169: add bit description for the TxPoll register
  r8169: cleanup
  r8169: remove the media option
  r8169: small 8101 comment
  r8169: confusion between hardware and IP header alignment
  r8169: merge with version 8.001.00 of Realtek's r8168 driver
  r8169: merge with version 6.001.00 of Realtek's r8169 driver
  r8169: prettify mac_version
  r8169: populate the hw_start handler for the 8110
  r8169: populate the hw_start handler for the 8168
  ...

The CPU must not touch the buffer after it was DMA-mapped.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

The CPU must not touch the buffer after it was DMA-mapped.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

  - The CPU must not touch the buffer after it was DMA-mapped.
  - The size argument of dma_unmap_single(...page_table...) was bogus.
  - Move a comment closer to the code to which it refers to.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Add rudimentary check for the case that the page table overflows due to
merging of s/g elements by the IOMMU.  This would have lead to
overwriting of arbitrary memory.

After this change I expect that an offending command will be
unsuccessfully retried until the scsi_device is taken offline by SCSI
core.  It's a border case and not worth to implement a recovery
strategy.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

This is required per SBP-2 clause 5.2.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

noticed by Jay Fenlason
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: NKristian Høgsberg <krh@redhat.com>

Replace a cast with a container_of().  As long as nobody reorders the
structure elements, they do the same thing, but container_of() is more
readable.

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added complete_command_orb)
Acked-by: NKristian Høgsberg <krh@redhat.com>

The isochronous packet format is still not documented, but this
is a good first step.
Signed-off-by: NKristian Høgsberg <krh@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (format, wording)

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

This affects of course only the "soft shutdown" case, e.g. "modprobe -r
firewire-sbp2", while it doesn't matter for hot unplug.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

This currently only affects one bridge in the hardwired blacklist.
I don't own one of those, hence haven't tested it.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

cleanup after "firewire: support S100B...S400B and link slower than PHY"
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Use a speed probe to determine the speed over 1394b buses and of nodes
which report a link speed less than their PHY speed.

Log the effective maximum speed of newly created nodes in dmesg.

Also, read the config ROM (except bus info block) at the maximum speed
rather than S100.  This isn't a real optimization though because we
still only use quadlet read requests for the entire ROM.

The patch also adds support for S1600 and S3200, although such hardware
does not exist yet.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Table-based gap count optimization cannot be used if 1394b repeater PHYs
are present.  But it does work with 1394b leaf nodes.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: NKristian Høgsberg <krh@redhat.com>

Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>

Also remove some errno printouts which will be shown by infrastructure
code anyway.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>