This patch creates a common system reset routine for all 40x and 44x
systems. Previously only a 44x routine existed. But since this system
reset via the debug control register is common for 40x and 44x let's
share this code for all those platforms in ppc4xx_soc.c.

This patch also enables CONFIG_4xx_SOC for all 40x and 44x platforms.

Tested on Kilauea (405EX) and Canyonlands (440EX).
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This target produces a flat binary rather than an ELF file,
fixes the entry point at the beginning of the image, and takes
a complete device tree with no fixups needed.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The of_serial driver queries the current-speed property and attempts
to use it to register the custom_divisor property of the uart_port.
However, if current-speed is not set, then this code will dereference
a bad pointer.  The fix is to only set custom_divisor when a
current-speed property appears in the device tree.
Signed-off-by: NStephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The patch fixes a bug, where the PESDRn_UTLSET1 register was setup
wrongly resulting in a non working PCIe port 1. With this fix both
PCIe ports work fine again.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Since the arch/powerpc PCI subsystem now does a complete re-assignment of
the resources, we can move from the unconditional PCIe PHY reset to the
conditional version. Now the PHY is only reset, if no link is established yet.
An additional PHY reset (one is already done in U-Boot) leads to problems
with some Atheros PCIe boards and some HP FPGA PCIe designs.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Call dtc from the Makefile instead of the wrapper script so that the dt
blobs can be generated with a simple make invocation.

Using this patch allows board ports to trigger automatic building of .dtb
files by adding them to the image-y target list.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

show_mem() has no need to print the amount of free swap space manually
because show_free_areas() does this already and is called by the
former.

The two outputs only differ in text formatting:

  printk("Free swap  = %lukB\n", ...);
  printk("Free swap:       %6ldkB\n", ...);
Signed-off-by: NJohannes Weiner <hannes@saeurebad.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

show_mem() has no need to print the amount of free swap space manually
because show_free_areas() does this already and is called by the
former.

The two outputs only differ in text formatting:

  printk("Free swap  = %lukB\n", ...);
  printk("Free swap:       %6ldkB\n", ...);
Signed-off-by: NJohannes Weiner <hannes@saeurebad.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Robert P.J. Day proposed to use the macro FIELD_SIZEOF in replace of code
that matches its definition.

The modification was made using the following semantic patch
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@haskernel@
@@

#include <linux/kernel.h>

@depends on haskernel@
type t;
identifier f;
@@

- (sizeof(((t*)0)->f))
+ FIELD_SIZEOF(t, f)

@depends on haskernel@
type t;
identifier f;
@@

- sizeof(((t*)0)->f)
+ FIELD_SIZEOF(t, f)
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Old-world powermacs don't set L2CR or L3CR on processor upgrade cards.
This simple patch allows the setting of L3CR via a kernel parameter
(like the existing kernel parameter to set L2CR).
Signed-off-by: NRobert Brose <bob@qbjnet.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Split the device setup code in ps3_register_repository_device() in two
routines:
  1. ps3_setup_static_device(), to handle the setup of static devices in the
     PS3 repository, which can be __init,
  2. ps3_setup_dynamic_device(), to handle the setup of storage devices that
     may appear later in the PS3 repository.

This fixes a few section mismatch warnings.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

WARNING: vmlinux.o(.text+0xb41b0): Section mismatch in reference from the
function .add_memory() to the function .devinit.text:.arch_add_memory()
The function .add_memory() references
the function __devinit .arch_add_memory().
This is often because .add_memory lacks a __devinit
annotation or the annotation of .arch_add_memory is wrong.

arch_add_memory() is also not __devinit on other architectures
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

WARNING: vmlinux.o(.text+0x1e4c0): Section mismatch in reference from the
function .move_device_tree() to the function .init.text:.lmb_alloc_base()
The function .move_device_tree() references
the function __init .lmb_alloc_base().
This is often because .move_device_tree lacks a __init
annotation or the annotation of .lmb_alloc_base is wrong.

move_device_tree() is called from early_init_devtree() only, which is __init
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If the platform doesn't support hpte_removebolted(), gracefully
return failure rather than success.
Signed-off-by: NBadari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add Wake-on-LAN support to the PS3 Gelic network driver.
Other OS WOL support was introduced in PS3 system firmware 2.20.
Signed-off-by: NMasakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add Wake-on-LAN support to the PS3 system-manager.  Other OS WOL
support was introduced in PS3 system firmware 2.20.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

PS3 save power on halt:
  - Replace infinite busy loops by smarter loops calling
    lv1_pause() to save power.
  - Add ps3_halt() and ps3_sys_manager_halt().
  - Add __noreturn annotations.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Improve the debugging support of the PS3 bootwraper code:

 o Increase the size of the PS3 bootwrapper overlay from 256 to 512 bytes to
   allow for more debugging code in the overlay.
 o Use the dot symbol to set the size of __system_reset_overlay.  The
   assembler will then emit an error if the overlay code is too big.
 o Remove some unused instructions.
 o Update the text describing the PS3 bootwrapper overlay.
 o Add a check for null pointer writes.
 o Change hcall return value from s64.
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add a new routine ps3_get_speid() which returns the logical
SPE ID.  This ID is needed for profiling support.
Signed-off-by: NTakashi Yamamoto <TakashiA.Yamamoto@jp.sony.com>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Fix a typo bug 'unlikely(x) == y' and add an unlikely() call to
an unlikely code path in the PS3 interrupt routine ps3_get_irq().
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Add device tree file for Emerson KSI8560 board.
Signed-off-by: NAlexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add default config for Emerson KSI8560 board.
Signed-off-by: NAlexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add boot wrapper for Emerson KSI8560 board.
Signed-off-by: NAlexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The KSI8560 is a single compact, mid-, or full-size Advanced Mezzanine Card
(AdvancedMC™) based on the Freescale™ Semiconductor MPC8560 PowerQUICC III™
microprocessor. This product will serve in data and signaling applications such
as signaling gateways (SGW) and softswitch signaling interface cards.

The board has altera maxii CPLD, that is used to obtain and manage board
configuration. Also there are two SCC UART serial consoles and FCC ethernet,
that is routed to the front panel, while other ethernet controlers (TSEC's) are
routed to the backplane.
Signed-off-by: NAlexandr Smirnov <asmirnov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds the L2 cache node to the Taishan 440GX dts file.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds support for the 256k L2 cache found on some IBM/AMCC
4xx PPC's. It introduces a common 4xx SoC file (sysdev/ppc4xx_soc.c)
which currently "only" adds the L2 cache init code. Other common 4xx
stuff can be added later here.

The L2 cache handling code is a copy of Eugene's code in arch/ppc
with small modifications.

Tested on AMCC Taishan 440GX.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Currently Haleakala uses the Kilauea platform code. This patch adds
"haleakala" to the compatible property, in case later kernel versions
will introduce a Haleakala platform code.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The patch adds the Glacier dts. The Glacier is nearly identical to the
Canyonlands (460EX). Here the differences:

- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Major 259 has been assigned by lanana.  Use it.  Also, publish
/dev/icap[0-k] as the device entries, and register platform devices
named 'icap' to be consistent.
Signed-off-by: NStephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

It appears that in some cases, the sync word might not be recognized
by the hardware correctly.  If this happens, then attempting to read
from the port results in an unrecoverable error because of the design
of the FPGA core.  This patch updates the code to check the status of
the device before reading the IDCODE, in order to avoid entering this
unrecoverable state.  This patch also adds additional NOOP commands
into the sychronization sequence, which appears to be necessary to
avoid the condition on some hardware.
Signed-off-by: NStephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Both the buffer-based and fifo-based icap cores have a status
register.  Previously, this was only used internally to check whether
transactions have completed.  However, the status can be useful to the
main driver as well.  This patch exposes these status functions to the
main driver along with some masks for the differnet bits.
Signed-off-by: NStephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds TAH (TCP/IP Acceleration Hardware) support to the
taishan 440GX dts. It depends on the NEWEMAC/tah patch that adds the
compatible "ibm,tah" property to the matching table.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Use dcri_clrset() for PCIe SDR0 read/modify/write access.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds dcri_clrset() macro which does read/modify/write
on indirect dcr registers while holding indirect dcr lock.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

Add the cuboot wrapper for the AMCC 440EP Yosemite board
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The AMCC 440EP Yosemite board is very similar to the original AMCC Bamboo
board.  This adds a YOSEMITE option to Kconfig, and reuses the existing
bamboo board support in the kernel.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This adds a DTS file for the AMCC 440EP Yosemite board.
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>