Eachtime the ndo_set_rx_mode() routine is called, the driver programs the
multicast list in the adapter without checking if there are any changes to
the list. This leads to a flood of RX_FILTER cmds when a number of vlan
interfaces are configured over the device, as the ndo_ gets
called for each vlan interface. To avoid this, we now use __dev_mc_sync()
and __dev_uc_sync() API, but only to detect if there is a change in the
mc/uc lists. Now that we use this API, the code has to be-designed to
issue these API calls for each invocation of the be_set_rx_mode() call.
Signed-off-by: NSriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently removes a new vid from the adapter->vids[] array if
be_vid_config() returns an error, which occurs when there is an error in
HW/FW. This is wrong. After the HW/FW error is recovered from, we need the
complete vids[] array to re-program the vlan list.
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Lancer FW has a bug due to which in some cases vlan-promisc setting
is cleared eventhough the vlan-list programming did not succeed (via
VLAN_CONFIG) cmd. The driver has no way of knowing if the vlan-promisc
mode was cleared or not when this cmd fails. To work around this issue,
this patch first explicitly clears the vlan-promisc mode via RX_FILTER
cmd and then tries to program the vlan list.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vxlan driver has bypass for local vxlan traffic, but that
depends on information about all VNIs on local system in
vxlan driver. This is not available in case of LWT.
Therefore following patch disable encap bypass for LWT
vxlan traffic.

Fixes: ee122c79 ("vxlan: Flow based tunneling").
Reported-by: NJakub Libosvar <jlibosva@redhat.com>
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LWT user can specify destination as well as source ip address
for given tunnel endpoint. But vxlan is ignoring given source
ip address. Following patch uses both ip address to route the
tunnel packet. This consistent with other LWT implementations,
like GENEVE and GRE.

Fixes: ee122c79 ("vxlan: Flow based tunneling").
Signed-off-by: NPravin B Shelar <pshelar@ovn.org>
Acked-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The call site for this function appears as:

  #ifdef DEBUG
        data->msg_enable = DEBUG;
        dump_eth_one(dev);
  #endif

...leading to the following warning for !DEBUG builds:

drivers/net/ethernet/tundra/tsi108_eth.c:169:13: warning: 'dump_eth_one' defined but not used [-Wunused-function]
 static void dump_eth_one(struct net_device *dev)
             ^

...when using the arch/powerpc/configs/mpc7448_hpc2_defconfig

Put the function definition under the same #ifdef as the call site
to avoid the warning.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We correctly execute mlxsw_sp_port_dcb_fini() when port is removed, but
I missed its rollback in the error path of port creation, so add it.

Fixes: f00817df ("mlxsw: spectrum: Introduce support for Data Center Bridging (DCB)")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PFCC register is used to configure both PAUSE and PFC frames.
Therefore, when PFC frames are disabled we must make sure we don't
mistakenly also disable PAUSE frames (which might be enabled).

Fix this by packing the PFCC register with the current PAUSE settings.

Note that this register is also accessed via ethtool ops, but there we
are guaranteed to have PFC disabled.

Fixes: d81a6bdb ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When ieee_setpfc() gets called, PAUSE frames are not necessarily
disabled on the port.

Check if PAUSE frames are disabled or enabled and configure the port's
headroom buffer accordingly.

Fixes: d81a6bdb ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

USRIO and JUMBO CAPS have the same mask.
Fix the same.

Fixes: ce721a70 ("net: ethernet: cadence-macb: Add disabled usrio caps")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: NHarini Katakam <harinik@xilinx.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 32-bit (e.g. with m68k-linux-gnu-gcc-4.1):

    drivers/net/dsa/b53/b53_common.c: In function ‘b53_arl_read’:
    drivers/net/dsa/b53/b53_common.c:1072: warning: integer constant is too large for ‘long’ type

Fixes: 1da6df85 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit a94efbd7 ("ethernet: arc: emac_main: add missing of_node_put
after calling of_parse_phandle") added missing of_node_put after calling
of_parse_phandle, but missing the devm_ioremap_resource() error handling
case.
Signed-off-by: NWei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable is added to allow the driver an easy access to
it's own hw->priv when the op is invoked.

This fixes a crash in wlcore because it was relying on a
station pointer that wasn't initialized yet. It's the wrong
way to fix the crash, but it solves the problem for now and
it does make sense to have the hw pointer here.
Signed-off-by: NMaxim Altshul <maxim.altshul@ti.com>
[rewrite commit message, fix indentation]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver modifies the supplied NAPI budget in qlcnic_83xx_msix_tx_poll()
function. Instead, it should use the budget as it is.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a data structure corruption bug in the SRIOV VF mailbox
handler code. While handling mailbox commands from the atomic context,
driver is accessing and updating qlcnic_async_work_list_struct entry fields
in the async work list. These fields could be concurrently accessed by the
work function resulting in data corruption.

This patch restructures async mbx command handling by using a separate
async command list instead of using a list of work_struct structures.
A single work_struct is used to schedule and handle the async commands
with proper locking mechanism.
Signed-off-by: NRajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch remove the wrong substraction from info->data in
tg3_get_rxnfc function. Without this patch, the number of RSS
queues reported is less by one.
Reported-by: NMichal Soltys <soltys@ziu.info>
Signed-off-by: NSiva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the rx coalescing time is 0, interrupts
are not generated from the controller and rx path hangs.
To avoid this rx hang, updating the driver to not allow
rx coalescing time to be 0.
Signed-off-by: NSatish Baddipadige <satish.baddipadige@broadcom.com>
Signed-off-by: NSiva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Building with -Wmaybe-uninitialized shows a potential use of
an uninitialized variable:

drivers/net/ethernet/apm/xgene/xgene_enet_hw.c: In function 'xgene_enet_phy_connect':
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:802:23: warning: 'phy_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]

Although the compiler correctly identified this based on the function,
the current code is still safe as long dev->of_node is non-NULL
for the case of CONFIG_ACPI=n, which is currently the case.

The warning is now disabled by default, but still appears when
building with W=1, and other build test tools should be able to
detect it as well. Adding an #else clause here makes the code
more robust and makes it clear to the compiler that this cannot
happen.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: 8089a96f ("drivers: net: xgene: Add backward compatibility")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit e93762bb ("w1: masters: omap_hdq: add support for 1-wire
mode") added a statement to clear the hdq_irqstatus flags in
hdq_read_byte().

If the hdq reading process is scheduled slowly or interrupts are
disabled for a while the hardware read activity might already be
finished on entry of hdq_read_byte().  And hdq_isr() already has set the
hdq_irqstatus to 0x6 (can be seen in debug mode) denoting that both, the
TXCOMPLETE and RXCOMPLETE interrupts occurred in parallel.

This means there is no need to wait and the hdq_read_byte() can just
read the byte from the hdq controller.

By resetting hdq_irqstatus to 0 the read process is forced to be always
waiting again (because the if statement always succeeds) but the
hardware will not issue another RXCOMPLETE interrupt.  This results in a
false timeout.

After such a situation the hdq bus hangs.

Link: http://lkml.kernel.org/r/b724765f87ad276a69625bc19806c8c8844c4590.1469513669.git.hns@goldelico.comSigned-off-by: NH. Nikolaus Schaller <hns@goldelico.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The helper macro module_w1_family can be used in module drivers that
only register a w1 driver in their module init functions.  Add this
macro and use it in all applicable drivers.

Link: http://lkml.kernel.org/r/20160531204313.20979-2-afd@ti.comSigned-off-by: NAndrew F. Davis <afd@ti.com>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

PLATFORM_DEVID_AUTO can be used to have the platform core assign a
unique ID instead of manually creating one with IDA.  Do this in all
applicable drivers.

Link: http://lkml.kernel.org/r/20160531204313.20979-1-afd@ti.comSigned-off-by: NAndrew F. Davis <afd@ti.com>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add RapidIO switch driver for IDT Gen3 switch devices: RXS1632 and
RXS2448.

[alexandre.bounine@idt.com: fixup for original driver patch]
  Link: http://lkml.kernel.org/r/1469137596-18241-1-git-send-email-alexandre.bounine@idt.com
Link: http://lkml.kernel.org/r/1469125134-16523-14-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Tested-by: NBarry Wood <barry.wood@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Implement changes made in RapidIO specification rev.3 to LP-Serial Physical
Layer register definitions:

 - use per-port register offset calculations based on LP-Serial Extended
   Features Block (EFB) Register Map type (I or II) with different
   per-port offset step (0x20 vs 0x40 respectfully).

 - remove deprecated Parallel Physical layer definitions and related
   code.

[alexandre.bounine@idt.com: fix DocBook warning for gen3 update]
  Link: http://lkml.kernel.org/r/1469191173-19338-1-git-send-email-alexandre.bounine@idt.com
Link: http://lkml.kernel.org/r/1469125134-16523-12-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Tested-by: NBarry Wood <barry.wood@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Current definition of map_inb() mport operations callback uses u32 type
to specify required inbound window (IBW) size.  This is limiting factor
because existing hardware - tsi721 and fsl_rio, both support IBW size up
to 16GB.

Changing type of size parameter to u64 to allow IBW size configurations
larger than 4GB.

[alexandre.bounine@idt.com: remove compiler warning about size of constant]
  Link: http://lkml.kernel.org/r/20160802184856.2566-1-alexandre.bounine@idt.com
Link: http://lkml.kernel.org/r/1469125134-16523-11-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix lockdep warning during device probing: move sysfs initialization out
of code protected by a spin lock.

Link: http://lkml.kernel.org/r/1469125134-16523-10-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add checking for error code returned by HW-specific mbox open routines.
Ensure that resources are properly release if failed.

This patch is applicable to kernel versions starting from v2.6.15.

Link: http://lkml.kernel.org/r/1469125134-16523-9-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add advancing transfer queue immediately from transfer submit call.  DMA
performance improvement: This will start transfer without waiting for
'issue_pending' command if there is no DMA transfer in progress.

Link: http://lkml.kernel.org/r/1469125134-16523-8-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add module parameter to allow load time configuration of available
RapidIO messaging mailboxes (MBOX1 - MBOX4).

Having a messaging MBOX selector mask allows to define which MBOXes are
controlled by the mport device driver and reserve some of them for
direct use by other drivers.

Link: http://lkml.kernel.org/r/1469125134-16523-7-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Tested-by: NBarry Wood <barry.wood@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add PCIe Maximum Read Request Size (MRRS) adjustment parameter to allow
users to override configuration register value set during PCIe bus
initialization.

Performance of Tsi721 device as PCIe bus master can be improved if MRRS
is set to its maximum value (4096 bytes).  Some platforms have
limitations for supported MRRS and therefore the default value should be
preserved, unless it is known that given platform supports full set of
MRRS values defined by PCI Express specification.

Link: http://lkml.kernel.org/r/1469125134-16523-6-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add module parameters to allow load time configuration of DMA channels.

Depending on application, performance of DMA data transfers can benefit
from adjusted sizes of buffer descriptor ring and/or transaction
requests queue.

Having HW DMA channel selector mask allows to define which channels
(from seven available) are controlled by the mport device driver and
reserve some of them for direct use by other drivers.

Link: http://lkml.kernel.org/r/1469125134-16523-5-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Tested-by: NBarry Wood <barry.wood@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update return value description for rio_dma_prep_...  functions to
include error-valued pointer that can be returned by HW mport device
drivers.  Return values from these functions must be checked using
IS_ERR_OR_NULL macro.

This patch is applicable to kernel versions starting from v4.6-rc1.

Link: http://lkml.kernel.org/r/1469125134-16523-4-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Patch series "RapidIO subsystem updates".

This set of patches contains RapidIO subsystem fixes and updates that
have been made since kernel v4.6.  The most significant update brings
changes related to the latest revision of RapidIO specification
(rev.3.x) and introduction of next generation of RapidIO switches by IDT
(RXS1632 and RXS2448).

This patch (of 13):

This is RapidIO part of the original patch submitted by Joe Perches.
(see: https://lkml.org/lkml/2016/3/5/19)

Since commit 3cab1e71 ("lib/vsprintf: refactor duplicate code
to special_hex_number()") %pa uses have been output with a 0x prefix.

These 0x prefixes in the formats are unnecessary.

Link: http://lkml.kernel.org/r/1469125134-16523-2-git-send-email-alexandre.bounine@idt.comSigned-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add channelized messaging driver to support native RapidIO messaging
exchange between multiple senders/recipients on devices that use kernel
RapidIO subsystem services.

This device driver is the result of collaboration within the RapidIO.org
Software Task Group (STG) between Texas Instruments, Prodrive
Technologies, Nokia Networks, BAE and IDT.  Additional input was
received from other members of RapidIO.org.

The objective was to create a character mode driver interface which
exposes messaging capabilities of RapidIO endpoint devices (mports)
directly to applications, in a manner that allows the numerous and
varied RapidIO implementations to interoperate.

This char mode device driver allows user-space applications to setup
messaging communication channels using single shared RapidIO messaging
mailbox.

By default this driver uses RapidIO MBOX_1 (MBOX_0 is reserved for use by
RIONET Ethernet emulation driver).

[weiyj.lk@gmail.com: rapidio/rio_cm: fix return value check in riocm_init()]
  Link: http://lkml.kernel.org/r/1469198221-21970-1-git-send-email-alexandre.bounine@idt.com
Link: http://lkml.kernel.org/r/1468952862-18056-1-git-send-email-alexandre.bounine@idt.comSigned-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Tested-by: NBarry Wood <barry.wood@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Andre van Herk <andre.van.herk@prodrive-technologies.com>
Cc: Barry Wood <barry.wood@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some systems are memory constrained but they need to load very large
firmwares.  The firmware subsystem allows drivers to request this
firmware be loaded from the filesystem, but this requires that the
entire firmware be loaded into kernel memory first before it's provided
to the driver.  This can lead to a situation where we map the firmware
twice, once to load the firmware into kernel memory and once to copy the
firmware into the final resting place.

This creates needless memory pressure and delays loading because we have
to copy from kernel memory to somewhere else.  Let's add a
request_firmware_into_buf() API that allows drivers to request firmware
be loaded directly into a pre-allocated buffer.  This skips the
intermediate step of allocating a buffer in kernel memory to hold the
firmware image while it's read from the filesystem.  It also requires
that drivers know how much memory they'll require before requesting the
firmware and negates any benefits of firmware caching because the
firmware layer doesn't manage the buffer lifetime.

For a 16MB buffer, about half the time is spent performing a memcpy from
the buffer to the final resting place.  I see loading times go from
0.081171 seconds to 0.047696 seconds after applying this patch.  Plus
the vmalloc pressure is reduced.

This is based on a patch from Vikram Mulukutla on codeaurora.org:
  https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.18/commit/drivers/base/firmware_class.c?h=rel/msm-3.18&id=0a328c5f6cd999f5c591f172216835636f39bcb5

Link: http://lkml.kernel.org/r/20160607164741.31849-4-stephen.boyd@linaro.orgSigned-off-by: NStephen Boyd <stephen.boyd@linaro.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Vikram Mulukutla <markivx@codeaurora.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some low memory systems with complex peripherals cannot afford to have
the relatively large firmware images taking up valuable memory during
suspend and resume.  Change the internal implementation of
firmware_class to disallow caching based on a configurable option.  In
the near future, variants of request_firmware will take advantage of
this feature.

Link: http://lkml.kernel.org/r/20160607164741.31849-3-stephen.boyd@linaro.org
[stephen.boyd@linaro.org: Drop firmware_desc design and use flags]
Signed-off-by: NVikram Mulukutla <markivx@codeaurora.org>
Signed-off-by: NStephen Boyd <stephen.boyd@linaro.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some systems are memory constrained but they need to load very large
firmwares.  The firmware subsystem allows drivers to request this
firmware be loaded from the filesystem, but this requires that the
entire firmware be loaded into kernel memory first before it's provided
to the driver.  This can lead to a situation where we map the firmware
twice, once to load the firmware into kernel memory and once to copy the
firmware into the final resting place.

This design creates needless memory pressure and delays loading because
we have to copy from kernel memory to somewhere else.  This patch sets
adds support to the request firmware API to load the firmware directly
into a pre-allocated buffer, skipping the intermediate copying step and
alleviating memory pressure during firmware loading.  The drawback is
that we can't use the firmware caching feature because the memory for
the firmware cache is not managed by the firmware layer.

This patch (of 3):

We use similar structured code to read and write the kmapped firmware
pages.  The only difference is read copies from the kmap region and
write copies to it.  Consolidate this into one function to reduce
duplication.

Link: http://lkml.kernel.org/r/20160607164741.31849-2-stephen.boyd@linaro.orgSigned-off-by: NStephen Boyd <stephen.boyd@linaro.org>
Cc: Vikram Mulukutla <markivx@codeaurora.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move the DRIVER_NAME macro definition before the first usage site and
fix build error.

Link: http://lkml.kernel.org/r/20160801163937.GA28119@nazgul.tnicSigned-off-by: NBorislav Petkov <bp@suse.de>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kernel.h header doesn't directly use dynamic debug, instead we can
include it in module.c (which used it via kernel.h).  printk.h only uses
it if CONFIG_DYNAMIC_DEBUG is on, changing the inclusion to only happen
in that case.

Link: http://lkml.kernel.org/r/1468429793-16917-1-git-send-email-luisbg@osg.samsung.com
[luisbg@osg.samsung.com: include dynamic_debug.h in drb_int.h]
  Link: http://lkml.kernel.org/r/1468447828-18558-2-git-send-email-luisbg@osg.samsung.comSigned-off-by: NLuis de Bethencourt <luisbg@osg.samsung.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There was only one use of __initdata_refok and __exit_refok

__init_refok was used 46 times against 82 for __ref.

Those definitions are obsolete since commit 312b1485 ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")

This patch removes the following compatibility definitions and replaces
them treewide.

/* compatibility defines */
#define __init_refok     __ref
#define __initdata_refok __refdata
#define __exit_refok     __ref

I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)

[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.beSigned-off-by: NFabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>