* Add IDE_TFLAG_IN_FEATURE taskfile flag for reading Feature
  register and handle it in ->tf_read.

* Convert ide_read_error() to use ->tf_read instead of ->INB,
  then uninline and export it.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->set_irq method for setting nIEN bit of ATA Device Control
register and use it instead of ide_set_irq().

While at it:

* Use ->set_irq in init_irq() and do_reset1().

* Don't use HWIF() macro in ide_check_pm_state().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove ide_read_altstatus() inline helper.

* Add ->read_altstatus method for reading ATA Alternate Status
  register and use it instead of ->INB.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove ide_read_status() inline helper.

* Add ->read_status method for reading ATA Status register
  and use it instead of ->INB.

While at it:

* Don't use HWGROUP() macro.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->exec_command method for writing ATA Command register
and use it instead of ->OUTBSYNC.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Factor out simplex handling from ide_pci_dma_base() to
  ide_pci_check_simplex().

* Set hwif->dma_base early in ->init_dma method / ide_hwif_setup_dma()
  and reset it in ide_init_port() if DMA initialization fails.

* Use ->read_sff_dma_status instead of ->INB in ide_pci_dma_base().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Export sff_dma_ops and then remove ide_setup_dma().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use ->dma_base + offset instead of ->dma_{status,command}
  and remove no longer needed ->dma_{status,command}.

While at it:

* Use ATA_DMA_* defines.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->read_sff_dma_status method for reading DMA Status register
and use it instead of ->INB.

While at it:

* Use inb() directly in ns87415.c::ns87415_dma_end().

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add 'hw_regs_t **hws' argument to ide_device_add[_all]() and convert
  host drivers + ide_legacy_init_one() + ide_setup_pci_device[s]() to use
  it instead of calling ide_init_port_hw() directly.

  [ However if host has > 1 port we must still set hwif->chipset to hint
    consecutive ide_find_port() call that the previous slot is occupied. ]

* Unexport ide_init_port_hw().

v2:
* Use defines instead of hard-coded values in buddha.c, gayle.c and q40ide.c.
  (Suggested by Geert Uytterhoeven)

* Better patch description.

v3:
* Fix build problem in ide-cs.c. (Noticed by Stephen Rothwell)

There should be no functional changes caused by this patch.

Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove some code which has been made obsolete and hasn't worked properly
before anyway.  Part of the infrastructure may be reintroduced in a
follow up patch to implement a working command aborting facility.
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Currently, the code path executing an HDIO_DRIVE_RESET ioctl is broken
in various ways.  Most importantly, it is treated as an out of band
request in an illegal way which may very likely lead to system lock ups.
Use the drive's request queue to avoid this problem (and fix a locking
issue for free along the way).
Signed-off-by: NElias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Change ->port_init_devs method to take 'ide_drive_t *' as an argument
instead of 'ide_hwif_t *' and rename it to ->init_dev.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add 'parent' field to hw_regs_t for optional parent device pointer (needed
  by macio PMAC IDE controllers) and set hwif->dev in ide_init_port_hw().

* Update au1xxx-ide.c, sgiioc4.c, pmac.c and setup-pci.c accordingly.

v2:

* Update scc_pata.c.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move ide_hwifs[] from ide.c to ide-probe.c and make it static.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move PIO blacklist to ide-pio-blacklist.c.

While at it:

- fix comment

- fix whitespace damage

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

All ide_pio_cycle_time() users already select CONFIG_IDE_TIMINGS
so move the function from ide-lib.c to ide-timings.c.

While at it:

- convert ide_pio_cycle_time() to use ide_timing_find_mode()

- cleanup ide_pio_cycle_time() a bit

There should be no functional changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Don't include ide-timing.h in cs5535 and sis5513 host drivers
  (they don't need it currently).

* Convert ide-timing.h to ide-timings.c library and add CONFIG_IDE_TIMINGS
  config option to be selected by host drivers using the library.

While at it:

- fix ide_timing_find_mode() placement

v2:
* Add missing EXPORT_SYMBOLs. (Stephen Rothwell <sfr@canb.auug.org.au>)

There should be no functional changes caused by this patch.

Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move struct ide_timing and IDE_TIMING_* defines to <linux/ide.h>
from drivers/ide/ide-timing.h.

While at it:

- use u8/u16 instead of short for struct ide_timing fields

- use enum for IDE_TIMING_*

There should be no functional changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* ide-tape.c: add 'drive' argument to idetape_update_buffers().

* Add generic ide_pc_intr() helper to ide-atapi.c and then
  convert ide-{floppy,tape,scsi} device drivers to use it.

* ide-tape.c: remove no longer needed DBG_PC_INTR.

There should be no functional changes caused by this patch
(unless the debugging is explicitely compiled in).

Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add generic ide_issue_pc() helper to ide-atapi.c and then
convert ide-{floppy,tape,scsi} device drivers to use it.

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add PC_FLAG_DRQ_INTERRUPT pc flag, set it in ide*_do_request()
and check for it (instead of checking for IDE*_FLAG_DRQ_INTERRUPT)
in ide*_issue_pc().  This is a preparation for adding generic
ide_issue_pc() helper.

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide-atapi.c file for generic ATAPI support together with
  CONFIG_IDE_ATAPI config option.

* Add generic ide_transfer_pc() helper to ide-atapi.c and then
  convert ide-{floppy,tape,scsi} device drivers to use it.

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add PC_FLAG_ZIP_DRIVE pc flag, set it in idefloppy_do_request()
and check for it (instead of checking for IDEFLOPPY_FLAG_ZIP_DRIVE)
in idefloppy_transfer_pc().  This is a preparation for adding
generic ide_transfer_pc() helper.

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use PC_FLAG_DMA_OK flag instead of PC_FLAG_DMA_RECOMMENDED one.

* Remove no longer used PC_FLAG_DMA_RECOMMENDED flag.

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge pc->idefloppy_callback and pc->idetape_callback into pc->callback.

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functional changes caused by this patch.

Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_do_drive_cmd is called only with ide_preempt action argument. So
we can remove the action argument in ide_do_drive_cmd and ide_action_t
typedef.

This patch also includes two minor cleanups: 1) ide_do_drive_cmd
always succeeds so we don't need the return value; 2) the callers use
blk_rq_init before ide_do_drive_cmd so there is no need to initialize
rq->errors.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove drive->ctl (it is always equal to 0x08 after init time).

While at it:

* Use ATA_DEVCTL_OBS define.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since scc_pata host driver no longer uses IDE PCI layer / ide_dma_setup()
and all other ->mmio users set also IDE_HFLAG_MMIO host flag we can safely
remove ->mmio flag.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Move IRQ unmasking out from ->tf_load method to its users.

There should be no functional changes caused by this patch
(SELECT_MASK() is NOP except for hpt366, icside and sgiioc4).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Always call SELECT_MASK(..., 0) in ide_tf_load() (needs to be done
to match ide_set_irq(..., 1)) and then remove IDE_TFLAG_NO_SELECT_MASK
taskfile flag.

This change should only affect hpt366 and icside host drivers since
->maskproc(..., 0) for sgiioc4 is equivalent to ide_set_irq(..., 1).

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove obsoleted "ide=" kernel parameters.

* Remove no longer needed:
  - ide_setup()
  - parse_options()
  - __setup("", ...)
  - module_param(options, ...)

* Use module_{init,exit}() for MODULE=y case and remove MODULE ifdef.

* Make ide_*acpi* and ide_doubler variables static.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove obsoleted "idebus=" kernel parameter.

* Remove no longer needed ide_system_bus_speed() and system_bus_clock()
  (together with idebus_parameter and system_bus_speed variables).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ide_init_drive_cmd just calls blk_rq_init. This converts the users of
ide_init_drive_cmd to use blk_rq_init directly and removes
ide_init_drive_cmd.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Borislav Petkov <petkovbb@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add __ide_default_irq() inline helper and use it instead of
ide_default_irq() in ide-probe.c and ns87415.c (all host drivers
except IDE PCI ones always setup hwif->irq so it is enough to
check only for I/O bases 0x1f0 and 0x170).

This fixes post-2.6.25 regression since ide_default_irq()
define could shadow ide_default_irq() inline.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

I forgot to remove the ide_etrax100 chipset type when removing the
ETRAX_IDE driver.
Reported-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>