Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 29 12月, 2015 20 次提交
  3. 14 12月, 2015 5 次提交
  5. 13 12月, 2015 1 次提交
  7. 12 12月, 2015 3 次提交
    • M
      parisc iommu: fix panic due to trying to allocate too large region · e46e31a3
      由 Mikulas Patocka 提交于 
      When using the Promise TX2+ SATA controller on PA-RISC, the system often
crashes with kernel panic, for example just writing data with the dd
utility will make it crash.

Kernel panic - not syncing: drivers/parisc/sba_iommu.c: I/O MMU @ 000000000000a000 is out of mapping resources

CPU: 0 PID: 18442 Comm: mkspadfs Not tainted 4.4.0-rc2 #2
Backtrace:
 [<000000004021497c>] show_stack+0x14/0x20
 [<0000000040410bf0>] dump_stack+0x88/0x100
 [<000000004023978c>] panic+0x124/0x360
 [<0000000040452c18>] sba_alloc_range+0x698/0x6a0
 [<0000000040453150>] sba_map_sg+0x260/0x5b8
 [<000000000c18dbb4>] ata_qc_issue+0x264/0x4a8 [libata]
 [<000000000c19535c>] ata_scsi_translate+0xe4/0x220 [libata]
 [<000000000c19a93c>] ata_scsi_queuecmd+0xbc/0x320 [libata]
 [<0000000040499bbc>] scsi_dispatch_cmd+0xfc/0x130
 [<000000004049da34>] scsi_request_fn+0x6e4/0x970
 [<00000000403e95a8>] __blk_run_queue+0x40/0x60
 [<00000000403e9d8c>] blk_run_queue+0x3c/0x68
 [<000000004049a534>] scsi_run_queue+0x2a4/0x360
 [<000000004049be68>] scsi_end_request+0x1a8/0x238
 [<000000004049de84>] scsi_io_completion+0xfc/0x688
 [<0000000040493c74>] scsi_finish_command+0x17c/0x1d0

The cause of the crash is not exhaustion of the IOMMU space, there is
plenty of free pages. The function sba_alloc_range is called with size
0x11000, thus the pages_needed variable is 0x11. The function
sba_search_bitmap is called with bits_wanted 0x11 and boundary size is
0x10 (because dma_get_seg_boundary(dev) returns 0xffff).

The function sba_search_bitmap attempts to allocate 17 pages that must not
cross 16-page boundary - it can't satisfy this requirement
(iommu_is_span_boundary always returns true) and fails even if there are
many free entries in the IOMMU space.

How did it happen that we try to allocate 17 pages that don't cross
16-page boundary? The cause is in the function iommu_coalesce_chunks. This
function tries to coalesce adjacent entries in the scatterlist. The
function does several checks if it may coalesce one entry with the next,
one of those checks is this:

	if (startsg->length + dma_len > max_seg_size)
		break;

When it finishes coalescing adjacent entries, it allocates the mapping:

sg_dma_len(contig_sg) = dma_len;
dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE);
sg_dma_address(contig_sg) =
	PIDE_FLAG
	| (iommu_alloc_range(ioc, dev, dma_len) << IOVP_SHIFT)
	| dma_offset;

It is possible that (startsg->length + dma_len > max_seg_size) is false
(we are just near the 0x10000 max_seg_size boundary), so the funcion
decides to coalesce this entry with the next entry. When the coalescing
succeeds, the function performs
	dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE);
And now, because of non-zero dma_offset, dma_len is greater than 0x10000.
iommu_alloc_range (a pointer to sba_alloc_range) is called and it attempts
to allocate 17 pages for a device that must not cross 16-page boundary.

To fix the bug, we must make sure that dma_len after addition of
dma_offset and alignment doesn't cross the segment boundary. I.e. change
	if (startsg->length + dma_len > max_seg_size)
		break;
to
	if (ALIGN(dma_len + dma_offset + startsg->length, IOVP_SIZE) > max_seg_size)
		break;

This patch makes this change (it precalculates max_seg_boundary at the
beginning of the function iommu_coalesce_chunks). I also added a check
that the mapping length doesn't exceed dma_get_seg_boundary(dev) (it is
not needed for Promise TX2+ SATA, but it may be needed for other devices
that have dma_get_seg_boundary lower than dma_get_max_seg_size).
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NHelge Deller <deller@gmx.de>
      e46e31a3
    • A
      USB: add quirk for devices with broken LPM · ad87e032
      由 Alan Stern 提交于 
      Some USB device / host controller combinations seem to have problems
with Link Power Management.  For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.

This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-by: NSteinar H. Gunderson <sgunderson@bigfoot.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      ad87e032
    • M
      xhci: fix usb2 resume timing and races. · f69115fd
      由 Mathias Nyman 提交于 
      According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.

On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.

On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.

There are a few issues with this approach

1. A host initiated resume will also generate a resume event. The event
   handler will find the port in resume state, believe it's a device
   initiated resume, and act accordingly.

2. A port status request might cut the resume signalling short if a
   get_port_status request is handled during the host resume signalling.
   The port will be found in resume state. The timestamp is not set leading
   to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
   get_port_status will proceed with moving the port to U0.

3. If an error, or anything else happens to the port during device
   initiated resume signalling it will leave all the device resume
   parameters hanging uncleared, preventing further suspend, returning
   -EBUSY, and cause the pm thread to busyloop trying to enter suspend.

Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state

This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS

Cc: stable <stable@vger.kernel.org>
Reported-by: NDaniel J Blueman <daniel@quora.org>
Tested-by: NDaniel J Blueman <daniel@quora.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      f69115fd
  9. 11 12月, 2015 2 次提交
  11. 10 12月, 2015 4 次提交
    • J
      dm btree: fix bufio buffer leaks in dm_btree_del() error path · ed8b45a3
      由 Joe Thornber 提交于 
      If dm_btree_del()'s call to push_frame() fails, e.g. due to
btree_node_validator finding invalid metadata, the dm_btree_del() error
path must unlock all frames (which have active dm-bufio buffers) that
were pushed onto the del_stack.

Otherwise, dm_bufio_client_destroy() will BUG_ON() because dm-bufio
buffers have leaked, e.g.:
  device-mapper: bufio: leaked buffer 3, hold count 1, list 0
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
      ed8b45a3
    • J
      ipmi: move timer init to before irq is setup · 27f972d3
      由 Jan Stancek 提交于 
      We encountered a panic on boot in ipmi_si on a dell per320 due to an
uninitialized timer as follows.

static int smi_start_processing(void       *send_info,
                                ipmi_smi_t intf)
{
        /* Try to claim any interrupts. */
        if (new_smi->irq_setup)
                new_smi->irq_setup(new_smi);

 --> IRQ arrives here and irq handler tries to modify uninitialized timer

    which triggers BUG_ON(!timer->function) in __mod_timer().

 Call Trace:
   <IRQ>
   [<ffffffffa0532617>] start_new_msg+0x47/0x80 [ipmi_si]
   [<ffffffffa053269e>] start_check_enables+0x4e/0x60 [ipmi_si]
   [<ffffffffa0532bd8>] smi_event_handler+0x1e8/0x640 [ipmi_si]
   [<ffffffff810f5584>] ? __rcu_process_callbacks+0x54/0x350
   [<ffffffffa053327c>] si_irq_handler+0x3c/0x60 [ipmi_si]
   [<ffffffff810efaf0>] handle_IRQ_event+0x60/0x170
   [<ffffffff810f245e>] handle_edge_irq+0xde/0x180
   [<ffffffff8100fc59>] handle_irq+0x49/0xa0
   [<ffffffff8154643c>] do_IRQ+0x6c/0xf0
   [<ffffffff8100ba53>] ret_from_intr+0x0/0x11

        /* Set up the timer that drives the interface. */
        setup_timer(&new_smi->si_timer, smi_timeout, (long)new_smi);

The following patch fixes the problem.

To: Openipmi-developer@lists.sourceforge.net
To: Corey Minyard <minyard@acm.org>
CC: linux-kernel@vger.kernel.org
Signed-off-by: NJan Stancek <jstancek@redhat.com>
Signed-off-by: NTony Camuso <tcamuso@redhat.com>
Signed-off-by: NCorey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # Applies cleanly to 3.10-, needs small rework before
      27f972d3
    • J
      dm space map metadata: fix ref counting bug when bootstrapping a new space map · 50dd842a
      由 Joe Thornber 提交于 
      When applying block operations (BOPs) do not remove them from the
uncommitted BOP ring-buffer until after they've been applied -- in case
we recurse.

Also, perform BOP_INC operation, in dm_sm_metadata_create() and
sm_metadata_extend(), in terms of the uncommitted BOP ring-buffer rather
than using direct calls to sm_ll_inc().
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
      50dd842a
    • J
      dm thin metadata: fix bug when taking a metadata snapshot · 49e99fc7
      由 Joe Thornber 提交于 
      When you take a metadata snapshot the btree roots for the mapping and
details tree need to have their reference counts incremented so they
persist for the lifetime of the metadata snap.

The roots being incremented were those currently written in the
superblock, which could possibly be out of date if concurrent IO is
triggering new mappings, breaking of sharing, etc.

Fix this by performing a commit with the metadata lock held while taking
a metadata snapshot.
Signed-off-by: NJoe Thornber <ejt@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
      49e99fc7
  13. 09 12月, 2015 5 次提交