Jesse Gross says:

====================
A number of improvements for net-next/3.10.

Highlights include:

 * Properly exposing linux/openvswitch.h to userspace after the uapi
   changes.

 * Simplification of locking. It immediately makes things simpler to
   reason about and avoids holding RTNL mutex for longer than
   necessary. In the near future it will also enable tunnel
   registration and more fine-grained locking.

 * Miscellaneous cleanups and simplifications.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 7b7a2bbb (atl1: Remove unneeded PM_OPS definitions) removed the
definition of atl1_suspend for the !CONFIG_PM_SLEEP case.

So only call atl1_suspend() when CONFIG_PM_SLEEP is defined and fix the
following build error from randconfig:

drivers/net/ethernet/atheros/atlx/atl1.c: In function 'atl1_shutdown':
drivers/net/ethernet/atheros/atlx/atl1.c:2888:2: error: implicit declaration of function 'atl1_suspend' [-Werror=implicit-function-declaration]
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
this is a pull-request for net-next/master. It consists of a patch by
Oliver Hartkopp. In this patch he cleans up the sja1000 header file by
using a common prefix for all sja1000 defines.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using SIMPLE_DEV_PM_OPS can make the code smaller and simpler.

Also change CONFIG_PM to CONFIG_PM_SLEEP.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we can't _up() after changing the MTU, report the actual error instead
of -ENOMEM. It can be really misleading cause pch_gbe is usually used in
scenarios where the memory amount is really small, and thus hiding the
real cause.
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows setting VXLAN destination to unicast address.
It allows that VXLAN can be used as peer-to-peer tunnel without
multicast.

v4: generalize struct vxlan_dev, "gaddr" is replaced with vxlan_rdst.
    "GROUP" attribute is replaced with "REMOTE".
    they are based by David Stevens's comments.

v3: move a new attribute REMOTE into the last of an enum list
    based by Stephen Hemminger's comments.

v2: use a new attribute REMOTE instead of GROUP based by
    Cong Wang's comments.
Signed-off-by: NAtzm Watanabe <atzm@stratosphere.co.jp>
Acked-by: NDavid L Stevens <dlstevens@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to add a dozen unions each time at the start
of the function. So, do this once and use it instead. Thus, we
can remove some duplicate code and make it more readable.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sctp: Add buffer utilization fields to /proc/net/sctp/assocs

This patch adds the following fields to /proc/net/sctp/assocs output:

	- sk->sk_wmem_alloc as "wmema"	(transmit queue bytes committed)
	- sk->sk_wmem_queued as "wmemq"	(persistent queue size)
	- sk->sk_sndbuf as "sndbuf"	(size of send buffer in bytes)
	- sk->sk_rcvbuf as "rcvbuf"	(size of receive buffer in bytes)

When small DATA chunks containing 136 bytes data are sent the TX_QUEUE
(assoc->sndbuf_used) reaches a maximum of 40.9% of sk_sndbuf value when
peer.rwnd = 0. This was diagnosed from sk_wmem_alloc value reaching maximum
value of sk_sndbuf.

TX_QUEUE (assoc->sndbuf_used), sk_wmem_alloc and sk_wmem_queued values are
incremented in sctp_set_owner_w() for outgoing data chunks. Having access to
the above values in /proc/net/sctp/assocs will provide a better understanding
of SCTP buffer management.

With patch applied, example output when peer.rwnd = 0

where:
    ASSOC ffff880132298000 is sender
          ffff880125343000 is receiver

 ASSOC           SOCK            STY SST ST  HBKT ASSOC-ID TX_QUEUE RX_QUEUE \
ffff880132298000 ffff880124a0a0c0 2   1   3  29325    1      214656        0 \
ffff880125343000 ffff8801237d7700 2   1   3  36210    2           0   524520 \

UID   INODE LPORT  RPORT LADDRS <-> RADDRS       HBINT   INS  OUTS \
  0   25108 3455   3456  *10.4.8.3 <-> *10.5.8.3  7500     2     2 \
  0   27819 3456   3455  *10.5.8.3 <-> *10.4.8.3  7500     2     2 \

MAXRT T1X T2X RTXC   wmema   wmemq  sndbuf  rcvbuf
    4   0   0   72  525633  440320  524288  524288
    4   0   0    0       1       0  524288  524288
Signed-off-by: NDilip Daya <dilip.daya@hp.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the work has been scheduled from interrupt, and not been
cancelled when the driver is unloaded, which doesn't remove
the work item from the global workqueue. call the
cancel_work_sync when the driver is removed (rmmod'ed).

Cc: Sriram <srk@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Vinay Hegde <vinay.hegde@ti.com>
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update debugging messages to a more current style.

Emit these debugging messages at KERN_DEBUG instead
of KERN_DEFAULT.

Add and use neigh_dbg(level, fmt, ...) macro
Add dynamic_debug capability via pr_debug
Convert embedded function names to "%s: ", __func__
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implemented separate irq handling for edge and level type interrupt
configuration. For edge type interrupts calls to disable_irq_nosync()
and enable_irq() are removed. The at86rf230 resets the irq line only
after the irq status register is read. Disabling the irq can lock the
driver in situations where a irq is set by the radio while the driver
is still reading the frame buffer.

With irq_type configuration set to 0 the original behavior is
preserverd.

Additional the irq filter register is set to filter out all unused
interrupts and the irq status register is read in the probe
function to clear the irq line.
Signed-off-by: NSascha Herrmann <sascha@ps.nvbi.de>

Conflicts:
	drivers/net/ieee802154/at86rf230.c
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add option to at86rf230 platform data to configure the type of the
interrupt used by the driver. The irq polarity of the device will
be configured accordingly.
Signed-off-by: NSascha Herrmann <sascha@ps.nvbi.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Jay Cliburn <jcliburn@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a follow up patch to:

    f901b6bc can: sja1000: fix define conflict on SH

That patch fixed a define conflict between the SH architecture and the sja1000
driver, by addind a prefix to one macro only. This patch consistently renames
the prefix of the SJA1000 controller registers from "REG_" to "SJA1000_".
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Rather than defining ovs specific stats struct (vport_percpu_stats),
we can use existing pcpu_tstats to achieve exactly same functionality.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

Currently OVS uses combination of genl and rtnl lock to protect
datapath state.  This was done due to networking stack locking.
But this has complicated locking and there are few lock ordering
issues with new tunneling protocols.
Following patch simplifies locking by introducing new ovs mutex
and now this lock is used to protect entire ovs state.
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NJesse Gross <jesse@nicira.com>

Vlad Yasevich says:

====================
Current dev_[uc|mc]_addr_sync() API currently correctly syncs the
addresses to the first device.  Any subsequent calls to sync will
not do anything since the synched variable will be set.  This
variable is used as an optimization to skip over addresses that have
been synched.

There are some devices (ex: team) that attempt to do the above.  There
is other work in progress that needs to above to work corretly.

The short series introduces dev_[uc|mc]_addr_synch_multiple() that
allows multiple calls to sync to multiple different devices.  Original
API is left alone and still has the limitation.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Team drivers attempts to sync addresses to each of the port
devices; however, the current api doesn't really perform the sync
for any device after the first one.  Switch to using the new api
that will actually sync the addresses to all ports.

CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current implementation of dev_uc_sync/unsync() assumes that there is
a strict 1-to-1 relationship between the source and destination of the sync.
In other words, once an address has been synced to a destination device, it
will not be synced to any other device through the sync API.
However, there are some virtual devices that aggreate a number of lower
devices and need to sync addresses to all of them.  The current
API falls short there.

This patch introduces a new dev_uc_sync_multiple() api that can be called
in the above circumstances and allows sync to work for every invocation.

CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since dead only holds two states (0,1), make it a bool instead
of a 'char', which is more appropriate for its purpose.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is actually no need to keep this member in the structure, because
after init it's always 1 anyway, thus always kfree called. This seems to
be an ancient leftover from the very initial implementation from 2.5
times. Only in case the initialization of an association fails, we leave
base.malloced as 0, but we nevertheless kfree it in the error path in
sctp_association_new().
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first backtrace appears on tx path with DMA mapping operations debug
enabled.

[  345.637919] ------------[ cut here ]------------
[  345.637971] WARNING: at lib/dma-debug.c:937 check_unmap+0x4df/0x910()
[  345.637977] Hardware name: System Name
[  345.637987] sis900 0000:00:01.1: DMA-API: device driver failed to check map error[device address=0x000000000d4aed02] [si
ze=60 bytes] [mapped as single]
[  345.637993] Modules linked in: bridge stp llc dmfe sundance 3c59x sis900
[  345.638022] Pid: 0, comm: swapper Not tainted 3.9.0-rc6+ #4
[  345.638028] Call Trace:
[  345.638042]  [<c122097f>] ? check_unmap+0x4df/0x910
[  345.638059]  [<c102b19c>] warn_slowpath_common+0x7c/0xa0
[  345.638070]  [<c122097f>] ? check_unmap+0x4df/0x910
[  345.638081]  [<c102b23e>] warn_slowpath_fmt+0x2e/0x30
[  345.638092]  [<c122097f>] check_unmap+0x4df/0x910
[  345.638107]  [<c100bfeb>] ? save_stack_trace+0x2b/0x50
[  345.638120]  [<c107238e>] ? mark_lock+0x31e/0x5d0
[  345.638132]  [<c1072b2c>] ? __lock_acquire+0x4ec/0x7d0
[  345.638143]  [<c1220f6d>] debug_dma_unmap_page+0x6d/0x80
[  345.638166]  [<cf834dec>] sis900_interrupt+0x49c/0x860 [sis900]
[  345.638195]  [<c1094b73>] handle_irq_event_percpu+0x43/0x1c0
[  345.638206]  [<c1094d1e>] ? handle_irq_event+0x2e/0x60
[  345.638217]  [<c1094d27>] handle_irq_event+0x37/0x60
[  345.638235]  [<c10973f0>] ? irq_set_chip_data+0x40/0x40
[  345.638246]  [<c1097442>] handle_level_irq+0x52/0xa0
[  345.638251]  <IRQ>  [<c1003629>] ? do_IRQ+0x39/0xa0
[  345.638293]  [<c1484631>] ? common_interrupt+0x31/0x36
[  345.638347]  [<d08c2c52>] ? br_flood_forward+0x12/0x20 [bridge]
[  345.638364]  [<d08c2d40>] ? br_dev_queue_push_xmit+0x60/0x60 [bridge]
[  345.638381]  [<d08c3b2b>] ? br_handle_frame_finish+0x25b/0x280 [bridge]
[  345.638399]  [<d08c3ce3>] ? br_handle_frame+0x193/0x290 [bridge]
[  345.638416]  [<d08c3b50>] ? br_handle_frame_finish+0x280/0x280 [bridge]
[  345.638431]  [<c13b3c87>] ? __netif_receive_skb_core+0x1d7/0x710
[  345.638442]  [<c13b3b19>] ? __netif_receive_skb_core+0x69/0x710
[  345.638454]  [<c13b41e1>] ? __netif_receive_skb+0x21/0x70
[  345.638464]  [<c13b42b5>] ? process_backlog+0x85/0x130
[  345.638476]  [<c13b4bbb>] ? net_rx_action+0xfb/0x1d0
[  345.638497]  [<c1032768>] ? __do_softirq+0xa8/0x1f0
[  345.638527]  [<c147daad>] ? _raw_spin_unlock+0x1d/0x20
[  345.638538]  [<c10038c0>] ? handle_irq+0x20/0xd0
[  345.638550]  [<c1032f27>] ? irq_exit+0x97/0xa0
[  345.638560]  [<c1003632>] ? do_IRQ+0x42/0xa0
[  345.638580]  [<c104d003>] ? hrtimer_start+0x23/0x30
[  345.638580]  [<c1484631>] ? common_interrupt+0x31/0x36
[  345.638580]  [<c1008703>] ? default_idle+0x33/0xc0
[  345.638580]  [<c10086ac>] ? cpu_idle+0x4c/0x70
[  345.638580]  [<c14787e0>] ? rest_init+0xa0/0xb0
[  345.638580]  [<c1478740>] ? reciprocal_value+0x50/0x50
[  345.638580]  [<c16b5bcf>] ? start_kernel+0x28f/0x320
[  345.638580]  [<c16b54e0>] ? repair_env_string+0x60/0x60
[  345.638580]  [<c16b5269>] ? i386_start_kernel+0x39/0xa0
[  345.638580] ---[ end trace a244264b69b8a7ae ]---
[  345.638580] Mapped at:
[  345.638580]  [<c1221c65>] debug_dma_map_page+0x65/0x110
[  345.638580]  [<cf8355a9>] sis900_start_xmit+0x129/0x210 [sis900]
[  345.638580]  [<c13b2527>] dev_hard_start_xmit+0x1b7/0x530
[  345.638580]  [<c13cc32e>] sch_direct_xmit+0x8e/0x280
[  345.638580]  [<c13b4e39>] dev_queue_xmit+0x1a9/0x5b0
Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.

Original-idea-by: <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The multicast and broadcast packets may have RTCF_LOCAL set in rt_flags
and therefore will be sent out bypassing encapsulation. This breaks
delivery of packets sent to the vxlan multicast group.
Disabling encapsulation bypass for multicasts and broadcasts fixes the
issue.
Signed-off-by: NMike Rapoport <mike.rapoport@ravellosystems.com>
Tested-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NSridhar Samudrala <sri@us.ibm.com>
Tested-by: NSridhar Samudrala <sri@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 10b96f73 (``tcp_memcontrol: remove a redundant statement
in tcp_destroy_cgroup()'') says ``We read the value but make no use
of it.'', but forgot to remove the variable declaration as well. This
was a follow-up commit of 3f134619 (``memcg: decrement static keys
at real destroy time'') that removed the read of variable 'val'.

This fixes therefore:

  CC      net/ipv4/tcp_memcontrol.o
net/ipv4/tcp_memcontrol.c: In function ‘tcp_destroy_cgroup’:
net/ipv4/tcp_memcontrol.c:67:6: warning: unused variable ‘val’ [-Wunused-variable]
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, sock_tx_timestamp() always returns 0. The comment that
describes the sock_tx_timestamp() function wrongly says that it
returns an error when an invalid argument is passed (from commit
20d49473, ``net: socket infrastructure for SO_TIMESTAMPING'').
Make the function void, so that we can also remove all the unneeded
if conditions that check for such a _non-existant_ error case in the
output path.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently "bridge fdb show dev vxlan0" lists loopback address as
"1.0.0.127". Using htonl(INADDR_LOOPBACK) rather than passing it
directly to vxlan_snoop fixes the problem.
Signed-off-by: NMike Rapoport <mike.rapoport@ravellosystems.com>
Acked-by: NCong Wang <xiyou.wangcong@gmail.com>
Acked-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unnecessary macros that duplicate generic
kernel functions.

When a struct net_device is available:

Convert printks to netdev_<level>
Convert netif_msg_<foo> and ugeth_<level> to netif_<level>

Add pr_fmt.  Standardize on newlines at end of format.
Remove some duplicated newlines from output.
Coalesce formats.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current logging style.

Convert pr_<level> to netdev_<level> when a struct net_device is
available.  Add pr_fmt and neaten other formats too.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a more current logging message style.

Convert the printks where a struct net_device is available to
netdev_<level>.  Convert the other printks to pr_<level> and
add pr_fmt where appropriate.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can move th->check computation out of the loop, as compiler
doesn't know each skb initially share same tcp headers after
skb_segment()
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when booting a mx6 device we get the following on boot:

registered PHC device on eth%d

Fix it by printing the network device name only after it gets registered, so
that the following can be read now:

fec 2188000.ethernet eth0: registered PHC device 0
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Freescale Vybrid platform implentments MAC-ENET core
providing compatibility with half- or full-duplex
10/100 Mbit/s Ethernet LANs.
Signed-off-by: NJingchang Lu <b35083@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As network adapters supporting PTP are becoming more common, machines with
many NICs suddenly have many PHCs, too. The current limit of eight /dev/ptp*
char devices (and thus, 8 network interfaces with PHC) is insufficient. Let
the ptp driver allocate the char devices dynamically.

Tested with 28 PHCs, removing and re-adding some of them.

Thanks to Ben Hutchings for advice leading to simpler and cleaner patch.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I noticed that TSQ (TCP Small queues) was less effective when TSO is
turned off, and GSO is on. If BQL is not enabled, TSQ has then no
effect.

It turns out the GSO engine frees the original gso_skb at the time the
fragments are generated and queued to the NIC.

We should instead call the tcp_wfree() destructor for the last fragment,
to keep the flow control as intended in TSQ. This effectively limits
the number of queued packets on qdisc + NIC layers.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>