MAX6621 is a PECI-to-I2C translator provides an efficient, low-cost
solution for PECI-to-SMBus/I2C protocol conversion. It allows reading the
temperature from the PECI-compliant host directly from up to four
PECI-enabled CPUs.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Add the lantiq cpu temperature sensor support for xrx200.
Signed-off-by: NFlorian Eckert <fe@dev.tdt.de>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This driver is no longer needed:

 * It has no mainline users
 * It has no DT support and OMAP is DT only
 * iio-hwmon can be used for madc, which also works with DT
Signed-off-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

The ASPEED AST2400/2500 PWM controller supports 8 PWM output ports.
The ASPEED AST2400/2500 Fan tach controller supports 16 tachometer
inputs.
The device driver matches on the device tree node. The configuration
values are read from the device tree and written to the respective
registers.
The driver provides a sysfs entries through which the user can
configure the duty-cycle value (ranging from 0 to 100 percent) and read
the fan tach rpm value.
Signed-off-by: NJaghathiswari Rankappagounder Natarajan <jaghu@google.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This patch adds a HWMON driver for ST Microelectronics STTS751
temperature sensors.

Thanks-to: LABBE Corentin [for suggestions]
Thanks-to: Guenter Roeck [for suggestion and discussions]
Signed-off-by: NAndrea Merello <andrea.merello@gmail.com>
Cc: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Add support for the TI TMP108 temperature sensor with some device
configuration parameters.
Signed-off-by: NJohn Muir <john@jmuir.com>
[groeck: Initialize of_match_table]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Add support for the tc654 and tc655 fan controllers from Microchip.

http://ww1.microchip.com/downloads/en/DeviceDoc/20001734C.pdfSigned-off-by: NChris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: NRob Herring <robh@kernel.org>
[groeck: Fixed continuation line alignments]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This patch adds hardware temperature and power reading support for
APM X-Gene SoC using the mailbox communication interface.
Signed-off-by: NHoan Tran <hotran@apm.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This driver implements hardware monitoring and watchdog support
for the FTS BMC Chip "Teutates".
Signed-off-by: NThilo Cestonaro <thilo@cestona.ro>
[groeck: Updated subject and description; fixed dependencies]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Add support for the the INA3221 26v capable, Triple channel,
Bi-Directional, Zero-Drift, Low-/High-Side, Current/Voltage Monitor
with I2C interface.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This driver implements support for the Sensirion SHT3x-DIS chip,
a humidity and temperature sensor. Temperature is measured
in degrees celsius, relative humidity is expressed as a percentage.
In the sysfs interface, all values are scaled by 1000,
i.e. the value for 31.5 degrees celsius is 31500.
Signed-off-by: NPascal Sachs <pascal.sachs@sensirion.com>
[groeck: Fixed 'Variable length array is used' gcc warning]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Add basic support for the Maxim Integrated MAX31722/MAX31723 SPI
temperature sensors / thermostats.

Includes:
    - ACPI support;
    - raw temperature readings;
    - power management

Datasheet:
https://datasheets.maximintegrated.com/en/ds/MAX31722-MAX31723.pdfSigned-off-by: NTiberiu Breana <tiberiu.a.breana@intel.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Create a driver to support the hardware monitoring chip present in
the Zyxel NSA320 and some of the other Zyxel NAS devices.

The driver reads fan speed and temperature from a suitably
pre-programmed MCU on the device.
Signed-off-by: NAdam Baker <linux@baker-net.org.uk>
[groeck: Dropped .owner field initialization]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This adds support for the Linear Technology LTC2990  I2C System Monitor.
The LTC2990 supports a combination of voltage, current and temperature
monitoring. This driver currently only supports reading two currents
by measuring two differential voltages across series resistors, in
addition to the Vcc supply voltage and internal temperature.

This is sufficient to support the Topic Miami SOM which uses this chip
to monitor the currents flowing into the FPGA and the CPU parts.
Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

The vexpress hwmon implementation is currently just called vexpress.
This is a problem because it clashes with another module with the same
name in regulators.

This patch renames the vexpress hwmon implementation to vexpress-hwmon
so that there will be no clash in the module namespace.

Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: lm-sensors@lm-sensors.org
Reported-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

HTU21 is now supported by IIO, and can be instantiated as hwmon driver
using the iio-hwmon bridge. An explicit hwmon driver is no longer needed.

Cc: William Markezana <william.markezana@meas-spec.com>
Cc: Ludovic Tancerel <ludovic.tancerel@maplehightech.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

The driver supports the Maxim MAX31790.
Signed-off-by: NIl Han <corone.il.han@gmail.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Create a driver to add support for SoC sensors exported by the System
Control Processor (SCP) via the System Control and Power Interface
(SCPI). The supported sensor types is one of voltage, temperature,
current, and power.

The sensor labels and values provided by the SCP are exported via the
hwmon sysfs interface.
Signed-off-by: NPunit Agrawal <punit.agrawal@arm.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Cc: Sudeep Holla <sudeep.holla@arm.com>

Add hwmon driver for the Microchip TC74.

The TC74 is a single-input 8-bit I2C temperature sensor,
with +-2 degrees centigrade accuracy.
Signed-off-by: NMaciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This patch splits CONFIG_I8K compile option to SENSORS_DELL_SMM and CONFIG_I8K.
Option SENSORS_DELL_SMM is now used to enable compilation of dell-smm-hwmon
driver and old CONFIG_I8K option to enable /proc/i8k interface in driver.

So this change allows to compile dell-smm-hwmon driver without legacy /proc/i8k
interface which is needed only for old Dell Inspirion models or for userspace
i8kutils package.

For backward compatibility when CONFIG_I8K is enabled then also SENSORS_DELL_SMM
is enabled and so driver dell-smm-hwmon (with /proc/i8k) is compiled.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This commit moves i8k driver to hwmon tree under name dell-smm-hwmon which is
better name then abbreviation i8k. For backward compatibility is added macro
MODULE_ALIAS("i8k") so modprobe will load driver also old name i8k. CONFIG_I8K
compile option was not changed.

This commit also adds me as maintainer of this new dell-smm-hwmon driver and
remove Guenter Roeck from list who is implicit maintainer all hwmon drivers.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The NCT7904D is a hardware monitor supporting up to 20 voltage sensors,
internal temperature sensor, Intel PECI and AMD SB-TSI CPU temperature
interface, up to 12 fan tachometer inputs, up to 4 fan control channels
with SmartFan.
Signed-off-by: NVadim V. Vlasov <vvlasov@dev.rtsoft.ru>
[Guenter Roeck: Fixed whitespace errors, dropped redundant comment]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

The Intel 5500, 5520 and X58 chipsets embed a digital thermal sensor.
This new driver supports it.

Note that on many boards the sensor seems to be disabled and reports
the minimum value (36.5 degrees Celsius) all the time.
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Tested-by: NRomain Dolbeau <romain@dolbeau.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>

NCT7802Y is an I2C based hardware monitoring chip from Nuvoton.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Added driver to support the 14F021P00 BMC Hardware Monitoring.
The BMC is a Board Management Controller including monitoring of the
board voltages.
Signed-off-by: NAndreas Werner <andreas.werner@men.de>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

The pwm-fan driver enables control of fans connected to PWM lines.
This driver uses the PWM framework, so it is compatible with all
PWM devices that provide drivers through the PWM framework.
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Reviewed-by: NVarka Bhadram <varkabhadram@gmail.com>
Reviewed-by: NTobias Klauser <tklauser@distanz.ch>
[Guenter Roeck: Last argument to devm_of_pwm_get is pointer, use NULL]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This patch adds basic kernel support for reading power values, fan
speed rpm, voltage and temperature data on powernv platforms which
will be exported to user space through sysfs interface.

Test results:
-------------
[root@tul163p1 ~]# sensors
ibmpowernv-isa-0000
Adapter: ISA adapter
fan1:        5465 RPM  (min =    0 RPM)
fan2:        5152 RPM  (min =    0 RPM)
fan3:        5521 RPM  (min =    0 RPM)
fan4:        4891 RPM  (min =    0 RPM)
fan5:           0 RPM  (min =    0 RPM)
fan6:           0 RPM  (min =    0 RPM)
fan7:        7480 RPM  (min =    0 RPM)
fan8:        7944 RPM  (min =    0 RPM)
temp1:        +39.0°C  (high =  +0.0°C)
power1:      190.00 W

[root@tul163p1 ~]# ls /sys/devices/platform/
alarmtimer  ibmpowernv.0  power  rtc-generic  serial8250  uevent
[root@tul163p1 ~]# ls /sys/devices/platform/ibmpowernv.0/hwmon/hwmon0/
device	    fan2_min	fan4_min    fan6_min	fan8_min   power
fan1_fault  fan3_fault	fan5_fault  fan7_fault	in1_fault  power1_input
fan1_input  fan3_input	fan5_input  fan7_input	in2_fault  subsystem
fan1_min    fan3_min	fan5_min    fan7_min	in3_fault  temp1_input
fan2_fault  fan4_fault	fan6_fault  fan8_fault	in4_fault  temp1_max
fan2_input  fan4_input	fan6_input  fan8_input	name	   uevent
[root@tul163p1 ~]# ls /sys/class/hwmon/hwmon0/
device	    fan2_min	fan4_min    fan6_min	fan8_min   power
fan1_fault  fan3_fault	fan5_fault  fan7_fault	in1_fault  power1_input
fan1_input  fan3_input	fan5_input  fan7_input	in2_fault  subsystem
fan1_min    fan3_min	fan5_min    fan7_min	in3_fault  temp1_input
fan2_fault  fan4_fault	fan6_fault  fan8_fault	in4_fault  temp1_max
fan2_input  fan4_input	fan6_input  fan8_input	name	   uevent
[root@tul163p1 ~]#
Signed-off-by: NNeelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Driver for the TI TMP103.

The TI TMP103 is similar to the TMP102.  It differs from the TMP102
by having only 8 bit registers.
Signed-off-by: NHeiko Schocher <hs@denx.de>
[linux@roeck-us.net: Select REGMAP_I2C in Kconfig]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This patch adds support for Lattice's POWR1220 power manager IC. Read
access to all the ADCs on the chip are supported through the hwmon
sysfs files.
Signed-off-by: NScott Kanowitz <skanowitz@echo360.com>
[Guenter Roeck: Removed some extra ( )]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Add support for Sensirion SHTC1 and compatible temperature and humidity
sensors.
Signed-off-by: NTomas Pop <tomas.pop@sensirion.com>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Nuvoton NCT6683D is an eSIO with hardware monitoring capabilities.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

This reverts commit 0de7f8a9.

This driver wasn't merged via the proper maintainers (my fault ... ooops !)
and has serious issues so let's take it out for now and have a new better
one be merged the right way
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
---

This patch adds basic kernel enablement for reading power values, fan
speed rpm and temperature values on powernv platforms which will
be exported to user space through sysfs interface.
Signed-off-by: NShivaprasad G Bhat <sbhat@linux.vnet.ibm.com>
Signed-off-by: NNeelesh Gupta <neelegup@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

ADC128D818 is a System Monitor with Temperature Sensor. It is similar to LM80
and LM96080, but has 16 bit wide sensor registers and no fan speed monitoring.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

LTC2945 is a system monitor that measures current, voltage, and power.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

LTC4260 is a Positive Voltage Hot Swap Controller.
The driver currently only supports voltage monitoring, not voltage control.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Driver Linear Technologies LTC4222 Dual Hot Swap Controller
The driver currently only supports voltage monitoring, not voltage control.
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Signed-off-by: NWilliam Markezana <william.markezana@meas-spec.com>
[Guenter Roeck - minor formatting changes]
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

GMT G762/763 fan speed PWM controller is connected directly to a fan
and performs closed-loop or open-loop control of the fan speed. Two
modes - PWM or DC - are supported by the chip. Introduced driver
provides various knobs to control the operations of the chip (via
sysfs interface). Specific characteristics of the system can be passed
either using board init code or via DT. Documentation for both the
driver and DT bindings are also provided.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Tested-by: NSimon Guinot <simon.guinot@sequanux.org>
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>

Each of ST-Ericsson X500 chip set series consists of both ABX500 and DBX500
chips. This is ABX500 hwmon driver, where the abx500.c is a common layer for
all ABX500s, and the ab8500.c is specific for AB8500 chip. Under this designed
structure, other chip specific files can be added simply using the same common
layer abx500.c.
Signed-off-by: NHongbo Zhang <hongbo.zhang@linaro.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NAnton Vorontsov <anton@enomsg.org>