Add group configuration for uarts that are cut down
variants, the standard being full, i.e. all signals,
flow control, i.e. rx/tx and cts/rts, and rx/tx only.

This allows us to be more precise in which pins we're
actually using.

Unfortunately the existing naming scheme leaves things
to be desired, e.g. uart3grp0 means RX/TX and CTS/RTS,
yet uart0grp0 means all pins.
Since the exising suffixes have different meaning for
different uarts, and the fact that we cannot change
the name of existing groups, makes it hard to use a
descriptive name for the newly added groups.
Signed-off-by: NNiklas Cassel <niklas.cassel@axis.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add missing pin group uart5nocts (all pins except cts), which has been
supported by the artpec6 pinctrl driver since its initial submission.

Fixes: 00df0582 ("pinctrl: Add pincontrol driver for ARTPEC-6 SoC")
Signed-off-by: NNiklas Cassel <niklas.cassel@axis.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add group configuration for uarts that are cut down
variants, the standard being full, i.e. all signals,
flow control, i.e. rx/tx and cts/rts, and rx/tx only.

This allows us to be more precise in which pins we're
actually using.
Signed-off-by: NJesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Now that arch/metag/ has been removed, along with TZ1090 SoC support,
remove the TZ1090 pinctrl drivers. They are of no value without the
architecture and SoC platform code.
Signed-off-by: NJames Hogan <jhogan@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-metag@vger.kernel.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The mcp23s08 series device can be configured for wired and interrupts
using an external pull-up and open drain output via the IOCON_ODR bit.
And "drive-open-drain" property to enable this.
Reviewed-by: NSebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Reviewed-by: NJan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This flag set the mcp23s08 device irq type to open drain active low.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

one_regmap_config is always null if mcp type is MCP_TYPE_S18.
Remove the null check so that the mcp23s18 will probe.

Fixes: 1781af56 ("pinctrl: mcp23s08: spi: Fix duplicate pinctrl debugfs entries")
Signed-off-by: NPhil Reid <preid@electromag.com.au>
Reviewed-by: NJan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

On boot, gpiochip_add_data() initializes the FLAG_IS_OUT bit in
desc->flags iff its gpio_chip does not have ->direction_input() handler,
else it is initialized to 0, which implies the GPIO is an "input".

Later, the sysfs "direction" handler will use gpiod_get_direction() to
get the current direction, but if no ->get_direction() handler is
installed, the result will just be the current (initial) value of flags,
which will always be OUT irregardless of the initial register value.

Add a get_direction() handler to pinctrl-amd to fix this and always
provide the correct value for direction.
Signed-off-by: NDaniel Kurtz <djkurtz@chromium.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The function ocelot_pinctrl_probe is local to the source and does not
need to be in global scope, so make it static.

Cleans up sparse warning:
drivers/pinctrl/pinctrl-ocelot.c:465:5: warning: symbol
'ocelot_pinctrl_probe' was not declared. Should it be static?
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The MUSB block in the Nomadik has two pin settings: high speed or
full speed. These correspond to two unique pin group settings: all
pins set to function B for high speed and all set to function C
for full speed. Full speed uses more pins than high speed.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The base of the TLMM gpiochip should not be statically defined as 0, fix
this to not artificially restrict the existence of multiple pinctrl-msm
devices.

Fixes: f365be09 ("pinctrl: Add Qualcomm TLMM driver")
Reported-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This is a bit more involved because the pinctrl core so far always
assumed that one device (with a unique dev_name) only contains a single
pinctrl thing. This is not true for the mcp23s08 driver for chips
connected over SPI. They have a "logical address" which means that
several chips can share one physical CS signal.

A downside of this patch are some possibly ugly names for the debugfs
entries, such as "spi1.1-mcp23xxx-pinctrl.2", etc.
Signed-off-by: NJan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When several devices are sharing one hardware SPI CS, there is no visual
clue in `lsgpio` or in /sys/kernel/debug/gpio about which one is which
one. Stuff depends on the enumeration order, and therefore lower chip
addresses always go first, but that's just an implementation detail.
This change includes the device-specific address in the debug output:

  gpiochip4: GPIOs 464-479, parent: spi/spi1.1, mcp23s17.2, can sleep:
  gpiochip3: GPIOs 480-495, parent: spi/spi1.1, mcp23s17.1, can sleep:
Signed-off-by: NJan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The SPI version of this chip allows several devices to be present on the
same SPI bus via a local address. If this is in action and if the kernel
has debugfs, however, the code attempts to create duplicate entries for
the regmap's debugfs:

  mcp23s08 spi1.1: Failed to create debugfs directory

This patch simply assigns a local name matching the device logical
address to the `struct regmap_config`.

No changes are needed for MCP23S18 because that device does not support
any logical addressing. Similarly, I2C devices do not need any action,
either, because they are already different in their I2C address.

A similar problem is present for the pinctrl debugfs instance, but that
one is not addressed by this patch.
Signed-off-by: NJan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds the pinctrl definitions for the TLMM of SDM845.
Signed-off-by: NKyle Yan <kyan@codeaurora.org>
Signed-off-by: NRajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds the DeviceTree binding for the Qualcomm SDM845 TLMM block.
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

except, again, POLLFREE and POLL_BUSY_LOOP.

With this, we finally get to the promised end result:

 - POLL{IN,OUT,...} are plain integers and *not* in __poll_t, so any
   stray instances of ->poll() still using those will be caught by
   sparse.

 - eventpoll.c and select.c warning-free wrt __poll_t

 - no more kernel-side definitions of POLL... - userland ones are
   visible through the entire kernel (and used pretty much only for
   mangle/demangle)

 - same behavior as after the first series (i.e. sparc et.al. epoll(2)
   working correctly).
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:

    for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
        L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
        for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
    done

with de-mangling cleanups yet to come.

NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do.  But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.

The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull more poll annotation updates from Al Viro:
 "This is preparation to solving the problems you've mentioned in the
  original poll series.

  After this series, the kernel is ready for running

      for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
            L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
            for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
      done

  as a for bulk search-and-replace.

  After that, the kernel is ready to apply the patch to unify
  {de,}mangle_poll(), and then get rid of kernel-side POLL... uses
  entirely, and we should be all done with that stuff.

  Basically, that's what you suggested wrt KPOLL..., except that we can
  use EPOLL... instead - they already are arch-independent (and equal to
  what is currently kernel-side POLL...).

  After the preparations (in this series) switch to returning EPOLL...
  from ->poll() instances is completely mechanical and kernel-side
  POLL... can go away. The last step (killing kernel-side POLL... and
  unifying {de,}mangle_poll() has to be done after the
  search-and-replace job, since we need userland-side POLL... for
  unified {de,}mangle_poll(), thus the cherry-pick at the last step.

  After that we will have:

   - POLL{IN,OUT,...} *not* in __poll_t, so any stray instances of
     ->poll() still using those will be caught by sparse.

   - eventpoll.c and select.c warning-free wrt __poll_t

   - no more kernel-side definitions of POLL... - userland ones are
     visible through the entire kernel (and used pretty much only for
     mangle/demangle)

   - same behavior as after the first series (i.e. sparc et.al. epoll(2)
     working correctly)"

* 'work.poll2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  annotate ep_scan_ready_list()
  ep_send_events_proc(): return result via esed->res
  preparation to switching ->poll() to returning EPOLL...
  add EPOLLNVAL, annotate EPOLL... and event_poll->event
  use linux/poll.h instead of asm/poll.h
  xen: fix poll misannotation
  smc: missing poll annotations

Pull xtense fix from Max Filippov:
 "Build fix for xtensa architecture with KASAN enabled"

* tag 'xtensa-20180211' of git://github.com/jcmvbkbc/linux-xtensa:
  xtensa: fix build with KASAN

Pull nios2 update from Ley Foon Tan:

 - clean up old Kconfig options from defconfig

 - remove leading 0x and 0s from bindings notation in dts files

* tag 'nios2-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2:
  nios2: defconfig: Cleanup from old Kconfig options
  nios2: dts: Remove leading 0x and 0s from bindings notation

The commit 917538e2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT
usage") removed KASAN_SHADOW_SCALE_SHIFT definition from
include/linux/kasan.h and added it to architecture-specific headers,
except for xtensa. This broke the xtensa build with KASAN enabled.
Define KASAN_SHADOW_SCALE_SHIFT in arch/xtensa/include/asm/kasan.h

Reported by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 917538e2 ("kasan: clean up KASAN_SHADOW_SCALE_SHIFT usage")
Acked-by: NAndrey Konovalov <andreyknvl@google.com>
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>

Remove old, dead Kconfig option INET_LRO. It is gone since
commit 7bbf3cae ("ipv4: Remove inet_lro library").
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Acked-by: NLey Foon Tan <ley.foon.tan@intel.com>

Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:

Warning (unit_address_format): Node /XXX unit name should not have leading "0x"

and

Warning (unit_address_format): Node /XXX unit name should not have leading 0s

Converted using the following command:

find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -E -i -e "s/@0x([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" -e "s/@0+([0-9a-fA-F\.]+)\s?\{/@\L\1 \{/g" {} +

For simplicity, two sed expressions were used to solve each warnings separately.

To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:

https://elinux.org/Device_Tree_Linux#Linux_conventions

This is a follow up to commit 4c9847b7 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: NDavid Daney <ddaney@caviumnetworks.com>
Suggested-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMathieu Malaterre <malat@debian.org>
Acked-by: NLey Foon Tan <ley.foon.tan@intel.com>

Pull PCI fix from Bjorn Helgaas:
 "Fix a POWER9/powernv INTx regression from the merge window (Alexey
  Kardashevskiy)"

* tag 'pci-v4.16-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  powerpc/pci: Fix broken INTx configuration via OF

Pull block fixes from Jens Axboe:
 "A few fixes to round off the merge window on the block side:

   - a set of bcache fixes by way of Michael Lyle, from the usual bcache
     suspects.

   - add a simple-to-hook-into function for bpf EIO error injection.

   - fix blk-wbt that mischarectized flushes as reads. Improve the logic
     so that flushes and writes are accounted as writes, and only reads
     as reads. From me.

   - fix requeue crash in BFQ, from Paolo"

* tag 'for-linus-20180210' of git://git.kernel.dk/linux-block:
  block, bfq: add requeue-request hook
  bcache: fix for data collapse after re-attaching an attached device
  bcache: return attach error when no cache set exist
  bcache: set writeback_rate_update_seconds in range [1, 60] seconds
  bcache: fix for allocator and register thread race
  bcache: set error_limit correctly
  bcache: properly set task state in bch_writeback_thread()
  bcache: fix high CPU occupancy during journal
  bcache: add journal statistic
  block: Add should_fail_bio() for bpf error injection
  blk-wbt: account flush requests correctly

Pull x86 platform driver updates from Darren Hart:
 "Mellanox fixes and new system type support.

  Mostly data for new system types with a correction and an
  uninitialized variable fix"

[ Pulling from github because git.infradead.org currently seems to be
  down for some reason, but Darren had a backup location    - Linus ]

* tag 'platform-drivers-x86-v4.16-3' of git://github.com/dvhart/linux-pdx86:
  platform/x86: mlx-platform: Add support for new 200G IB and Ethernet systems
  platform/x86: mlx-platform: Add support for new msn201x system type
  platform/x86: mlx-platform: Add support for new msn274x system type
  platform/x86: mlx-platform: Fix power cable setting for msn21xx family
  platform/x86: mlx-platform: Add define for the negative bus
  platform/x86: mlx-platform: Use defines for bus assignment
  platform/mellanox: mlxreg-hotplug: Fix uninitialized variable

Merge tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform

Pull chrome platform updates from Benson Leung:

 - move cros_ec_dev to drivers/mfd

 - other small maintenance fixes

[ The cros_ec_dev movement came in earlier through the MFD tree  - Linus ]

* tag 'chrome-platform-for-linus-4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/bleung/chrome-platform:
  platform/chrome: Use proper protocol transfer function
  platform/chrome: cros_ec_lpc: Add support for Google Glimmer
  platform/chrome: cros_ec_lpc: Register the driver if ACPI entry is missing.
  platform/chrome: cros_ec_lpc: remove redundant pointer request
  cros_ec: fix nul-termination for firmware build info
  platform/chrome: chromeos_laptop: make chromeos_laptop const

Pull KVM updates from Radim Krčmář:
 "ARM:

   - icache invalidation optimizations, improving VM startup time

   - support for forwarded level-triggered interrupts, improving
     performance for timers and passthrough platform devices

   - a small fix for power-management notifiers, and some cosmetic
     changes

  PPC:

   - add MMIO emulation for vector loads and stores

   - allow HPT guests to run on a radix host on POWER9 v2.2 CPUs without
     requiring the complex thread synchronization of older CPU versions

   - improve the handling of escalation interrupts with the XIVE
     interrupt controller

   - support decrement register migration

   - various cleanups and bugfixes.

  s390:

   - Cornelia Huck passed maintainership to Janosch Frank

   - exitless interrupts for emulated devices

   - cleanup of cpuflag handling

   - kvm_stat counter improvements

   - VSIE improvements

   - mm cleanup

  x86:

   - hypervisor part of SEV

   - UMIP, RDPID, and MSR_SMI_COUNT emulation

   - paravirtualized TLB shootdown using the new KVM_VCPU_PREEMPTED bit

   - allow guests to see TOPOEXT, GFNI, VAES, VPCLMULQDQ, and more
     AVX512 features

   - show vcpu id in its anonymous inode name

   - many fixes and cleanups

   - per-VCPU MSR bitmaps (already merged through x86/pti branch)

   - stable KVM clock when nesting on Hyper-V (merged through
     x86/hyperv)"

* tag 'kvm-4.16-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (197 commits)
  KVM: PPC: Book3S: Add MMIO emulation for VMX instructions
  KVM: PPC: Book3S HV: Branch inside feature section
  KVM: PPC: Book3S HV: Make HPT resizing work on POWER9
  KVM: PPC: Book3S HV: Fix handling of secondary HPTEG in HPT resizing code
  KVM: PPC: Book3S PR: Fix broken select due to misspelling
  KVM: x86: don't forget vcpu_put() in kvm_arch_vcpu_ioctl_set_sregs()
  KVM: PPC: Book3S PR: Fix svcpu copying with preemption enabled
  KVM: PPC: Book3S HV: Drop locks before reading guest memory
  kvm: x86: remove efer_reload entry in kvm_vcpu_stat
  KVM: x86: AMD Processor Topology Information
  x86/kvm/vmx: do not use vm-exit instruction length for fast MMIO when running nested
  kvm: embed vcpu id to dentry of vcpu anon inode
  kvm: Map PFN-type memory regions as writable (if possible)
  x86/kvm: Make it compile on 32bit and with HYPYERVISOR_GUEST=n
  KVM: arm/arm64: Fixup userspace irqchip static key optimization
  KVM: arm/arm64: Fix userspace_irqchip_in_use counting
  KVM: arm/arm64: Fix incorrect timer_is_pending logic
  MAINTAINERS: update KVM/s390 maintainers
  MAINTAINERS: add Halil as additional vfio-ccw maintainer
  MAINTAINERS: add David as a reviewer for KVM/s390
  ...

59f47eff ("powerpc/pci: Use of_irq_parse_and_map_pci() helper")
replaced of_irq_parse_pci() + irq_create_of_mapping() with
of_irq_parse_and_map_pci(), but neglected to capture the virq
returned by irq_create_of_mapping(), so virq remained zero, which
caused INTx configuration to fail.

Save the virq value returned by of_irq_parse_and_map_pci() and correct
the virq declaration to match the of_irq_parse_and_map_pci() signature.

Fixes: 59f47eff "powerpc/pci: Use of_irq_parse_and_map_pci() helper"
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
[bhelgaas: changelog]
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Pull more Kbuild updates from Masahiro Yamada:
 "Makefile changes:
   - enable unused-variable warning that was wrongly disabled for clang

  Kconfig changes:
   - warn about blank 'help' and fix existing instances
   - fix 'choice' behavior to not write out invisible symbols
   - fix misc weirdness

  Coccinell changes:
   - fix false positive of free after managed memory alloc detection
   - improve performance of NULL dereference detection"

* tag 'kbuild-v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (21 commits)
  kconfig: remove const qualifier from sym_expand_string_value()
  kconfig: add xrealloc() helper
  kconfig: send error messages to stderr
  kconfig: echo stdin to stdout if either is redirected
  kconfig: remove check_stdin()
  kconfig: remove 'config*' pattern from .gitignnore
  kconfig: show '?' prompt even if no help text is available
  kconfig: do not write choice values when their dependency becomes n
  coccinelle: deref_null: avoid useless computation
  coccinelle: devm_free: reduce false positives
  kbuild: clang: disable unused variable warnings only when constant
  kconfig: Warn if help text is blank
  nios2: kconfig: Remove blank help text
  arm: vt8500: kconfig: Remove blank help text
  MIPS: kconfig: Remove blank help text
  MIPS: BCM63XX: kconfig: Remove blank help text
  lib/Kconfig.debug: Remove blank help text
  Staging: rtl8192e: kconfig: Remove blank help text
  Staging: rtl8192u: kconfig: Remove blank help text
  mmc: kconfig: Remove blank help text
  ...

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull misc vfs fixes from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  seq_file: fix incomplete reset on read from zero offset
  kernfs: fix regression in kernfs_fop_write caused by wrong type

This function returns realloc'ed memory, so the returned pointer
must be passed to free() when done.  So, 'const' qualifier is odd.
It is allowed to modify the expanded string.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

We already have xmalloc(), xcalloc().  Add xrealloc() as well
to save tedious error handling.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

It adds support for new Mellanox system types of basic classes qmb7, sn34,
sn37, containing systems QMB700 (40x200GbE InfiniBand switch), SN3700
(32x200GbE and 16x400GbE Ethernet switch) and SN3410 (6x400GbE plus
48x50GbE Ethernet switch). These are the Top of the Rack systems, equipped
with Mellanox COM-Express carrier board and switch board with Mellanox
Quantum device, which supports InfiniBand switching with 40X200G ports and
line rate of up to HDR speed or with Mellanox Spectrum-2 device, which
supports Ethernet switching with 32X200G ports line rate of up to HDR
speed.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Signed-off-by: NDarren Hart (VMware) <dvhart@infradead.org>

It adds support for new Mellanox system types of basic half unit size
class msn201x, containing system MSN2010 (18x10GbE plus 4x4x25GbE) half
and its derivatives. This is the Top of the Rack system, equipped with
Mellanox Small Form Factor carrier board and switch board with Mellanox
Spectrum device, which supports Ethernet switching with 32X100G ports line
rate of up to EDR speed.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Signed-off-by: NDarren Hart (VMware) <dvhart@infradead.org>

It adds support for new Mellanox system types of basic class msn274x,
containing system MSN2740 (32x100GbE Ethernet switch with cost reduction)
and its derivatives. These are the Top of the Rack system, equipped with
Mellanox Small Form Factor carrier board and switch board with Mellanox
Spectrum device, which supports Ethernet switching with 32X100G ports line
rate of up to EDR speed.
Signed-off-by: NVadim Pasternak <vadimp@mellanox.com>
Signed-off-by: NDarren Hart (VMware) <dvhart@infradead.org>