Drivers should not assume that interface descriptors have been parsed in
any particular order so match on interface number instead when rejecting
JTAG interfaces.

Also use the interface struct device for notifications so that the
interface number is included.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

There exist many FT2232-based JTAG+UART adapter designs in which
FT2232 Channel A is used for JTAG and Channel B is used for UART.
The best way to handle them in Linux is to have the ftdi_sio driver
create a ttyUSB device only for Channel B and not for Channel A:
a ttyUSB device for Channel A would be bogus and will disappear as
soon as the user runs OpenOCD or other applications that access
Channel A for JTAG from userspace, causing undesirable noise for
users.  The ftdi_sio driver already has a dedicated quirk for such
JTAG+UART FT2232 adapters, and it requires assigning custom USB IDs
to such adapters and adding these IDs to the driver with the
ftdi_jtag_quirk applied.

Boutique hardware manufacturer Falconia Partners LLC has created a
couple of JTAG+UART adapter designs (one buffered, one unbuffered)
as part of FreeCalypso project, and this hardware is specifically made
to be used with Linux hosts, with the intent that Channel A will be
accessed only from userspace via appropriate applications, and that
Channel B will be supported by the ftdi_sio kernel driver, presenting
a standard ttyUSB device to userspace.  Toward this end the hardware
manufacturer will be programming FT2232 EEPROMs with custom USB IDs,
specifically with the intent that these IDs will be recognized by
the ftdi_sio driver with the ftdi_jtag_quirk applied.
Signed-off-by: NMychaela N. Falconia <falcon@freecalypso.org>
[johan: insert in PID order and drop unused define]
Cc: stable@vger.kernel.org
Signed-off-by: NJohan Hovold <johan@kernel.org>

The device added has an FTDI chip inside.
The device is used to connect Xsens USB Motion Trackers.

Cc: stable@vger.kernel.org
Signed-off-by: NPatrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop redundant URB transfer-buffer casts.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Only set the sysrq timestamp for console ports to avoid having every
driver also check the console flag when processing incoming data.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Only the last NUL in a packet should be flagged as a break character,
for example, to avoid dropping unrelated characters when IGNBRK is set.

Also make sysrq work by consuming the break character instead of having
it immediately cancel the sysrq request, and by not processing it
prematurely to avoid triggering a sysrq based on an unrelated character
received in the same packet (which was received *before* the break).

Note that the break flag can be left set also for a packet received
immediately following a break and that and an ending NUL in such a
packet will continue to be reported as a break as there's no good way to
tell it apart from an actual break.

Tested on FT232R and FT232H.

Fixes: 72fda3ca ("USB: serial: ftd_sio: implement sysrq handling on break")
Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Clean up receive processing by dropping the character pointer and
keeping the length argument unchanged throughout the function.

Also make it more apparent that sysrq processing can consume a
characters by adding an explicit continue.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Use an unsigned type for the process-packet buffer argument and give it
a more apt name.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This device presents itself as a USB hub with three attached devices:
 - An ACM serial port connected to the GPS module (not affected by this
   commit)
 - An FTDI serial port connected to the GPS module (1546:0502)
 - Another FTDI serial port connected to the ODIN-W2 radio module
   (1546:0503)

This commit registers U-Blox's VID and the PIDs of the second and third
devices.

Datasheet: https://www.u-blox.com/sites/default/files/C099-F9P-AppBoard-Mbed-OS3-FW_UserGuide_%28UBX-18063024%29.pdfSigned-off-by: NFabio D'Urso <fabiodurso@hotmail.it>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Both devices added here have a FTDI chip inside. The device from Echelon
is called 'Network Interface' it is actually a LON network gateway.

 ID 0403:8348 Future Technology Devices International, Ltd
 https://www.eltako.com/fileadmin/downloads/de/datenblatt/Datenblatt_PL-SW-PROF.pdf

 ID 0920:7500 Network Interface
 https://www.echelon.com/products/u20-usb-network-interfaceSigned-off-by: NBeni Mahler <beni.mahler@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Enable support for cbus gpios on FT232H. The cbus configuration is
stored in two words in the EEPROM at byte-offset 0x1a with the mux
config for ACBUS5, ACBUS6, ACBUS8 and ACBUS9 (only pins that can be
configured as I/O mode).

Tested using FT232H by configuring one ACBUS pin at a time.
Reviewed-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NMatthew Michilot <matthew.michilot@gmail.com>
[ johan: fix copy-paste error in commit message ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

This adds the vid:pid of the isodebug v1 isolated JTAG/SWD+UART. Only the
second channel is available for use as a serial port.
Signed-off-by: NAndreas Fritiofson <andreas.fritiofson@unjo.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

While there are a mix of things here, most of the stuff
were written from Kernel developer's PoV. So, add them to
the driver-api book.

A follow up for this patch would be to move documents from
there that are specific to sysadmins, adding them to the
admin-guide.
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: NJohan Hovold <johan@kernel.org>
Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be
automatically detected.
Signed-off-by: NGeorge McCollister <george.mccollister@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This adds the USB ID of the Hjelmslund Electronics USB485 Iso stick.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

There is a bug in the current GPIO code for ftdi_sio: it failed to take USB
autosuspend into account. If the device is in autosuspend, calls to
usb_control_msg() fail with -EHOSTUNREACH. Because the standard value for
autosuspend timeout is usually 2-5 seconds, this made it almost impossible
to use the GPIOs on machines that have USB autosuspend enabled. This patch
fixes the issue by acquiring a PM lock on the device for the duration of
the USB transfers. Tested on an FT231X device.
Signed-off-by: NKaroly Pados <pados@pados.hu>
[ johan: simplify code somewhat ]
Fixes: ba93cc7d ("USB: serial: ftdi_sio: implement GPIO support for FT-X devices")
Cc: stable <stable@vger.kernel.org>	# 4.20
Signed-off-by: NJohan Hovold <johan@kernel.org>

Improve baud-rate generation by using rounding-to-closest instead of
truncation in divisor calculation.

Results have been verified by logic analyzer on an FT232RT (232BM) chip.
The following table shows the wanted baud rate, the baud rate obtained
with the old method (truncation), with the new method (rounding) and the
baud rate generated by the windows 10 driver. The numbers in parentheses
is the error.

+- Wanted --+------ Old -------+------ New -------+------ Win -------+
|    9600   |    9600 (0.00%)  |    9604 (0.05%)  |    9605 (0.05%)  |
|   19200   |   19200 (0.00%)  |   19199 (0.01%)  |   19198 (0.01%)  |
|   38400   |   38395 (0.01%)  |   38431 (0.08%)  |   38394 (0.02%)  |
|   57600   |   57725 (0.22%)  |   57540 (0.10%)  |   57673 (0.13%)  |
|  115200   |  115307 (0.09%)  |  115330 (0.11%)  |  115320 (0.10%)  |
|  921600   |  919963 (0.18%)  |  920386 (0.13%)  |  920810 (0.09%)  |
|  961200   |  996512 (3.67%)  |  956480 (0.49%)  |  956937 (0.44%)  |
+-----------+------------------+------------------+------------------+

The error due to noise in the measurements is in the order of a few
tenths of a %. As can be seen, the baud rate is significantly improved
for some rates (e.g. 961200), and corresponds to the output given by the
windows driver.

The theoretical baud rate has been calculated for all baud rates from 1
to 3M, and as expected, the error is centered around 0, with a triangle
shape instead of a sawtooth, so the maximum error is decreased to half.
Signed-off-by: NNikolaj Fogh <nikolajfogh@gmail.com>
[ johan: edit commit message slightly ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

Reviewed-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Enable support for cbus gpios on FT232R. The cbus configuration is
stored in one word in the EEPROM at offset 0x0a (byte-offset 0x14) with
the mux config for CBUS0, CBUS1, CBUS2 and CBUS3 in bits 0..3, 4..7,
8..11 and 12..15, respectively.

Tested using FT232RL by configuring one cbus pin at a time.
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop the gpio line names, which cause gpiolib to complain loudly
whenever a second ftdi gpiochip is registered:

	gpio gpiochip5: Detected name collision for GPIO name 'CBUS0'
	gpio gpiochip5: Detected name collision for GPIO name 'CBUS1'
	gpio gpiochip5: Detected name collision for GPIO name 'CBUS2'
	gpio gpiochip5: Detected name collision for GPIO name 'CBUS3'

and also prevents the legacy sysfs interface from being used (as the
line names are used as device names whenever they are set):

	sysfs: cannot create duplicate filename '/class/gpio/CBUS0'

Until non-unique names are supported by gpiolib (without warnings and
stack dumps), let's leave the gpio lines unnamed.
Signed-off-by: NJohan Hovold <johan@kernel.org>

This patch allows using the CBUS pins of FT-X devices as GPIO in CBUS
bitbanging mode. There is no conflict between the GPIO and VCP
functionality in this mode. Tested on FT230X and FT231X.

As there is no way to request the current CBUS register configuration
from the device, all CBUS pins are set to a known state when the first
GPIO is requested. This allows using libftdi to set the GPIO pins
before loading this module for UART functionality, a behavior that
existing applications might be relying upon (though no specific case
is known to the authors of this patch).
Signed-off-by: NKaroly Pados <pados@pados.hu>
[ johan: minor style changes ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

Clean up the somewhat convoluted hardware-assisted flow control
handling.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Drop urb_ prefixes from value and index variables used in control
requests.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Replace all __u types with their u counterparts throughout the driver
(whose structures are not exported to user space).
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Since forever this driver has had IXON and IXOFF mixed up, and has used
the latter rather than the former to enable hardware-assisted software
flow control on output.
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Arrow USB Blaster integrated on MAX1000 board uses the same vendor ID
(0x0403) and product ID (0x6010) as the "original" FTDI device.

This patch avoids picking up by ftdi_sio of the first interface of this
USB device. After that this device can be used by Arrow user-space JTAG
driver.
Signed-off-by: NVasyl Vavrychuk <vvavrychuk@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

This reverts commit 79a0b331.

Turns out this is not an FTDI device after all.

Fixes: 79a0b331 ("USB: serial: ftdi_sio: add Id for Physik Instrumente E-870")
Reported-by: NMartin Teichmann <martin.teichmann@xfel.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds support for the Physik Instrumente E-870 PIShift Drive
Electronics, a Piezo motor driver.
Signed-off-by: NMartin Teichmann <martin.teichmann@xfel.eu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add device id for Harman FirmwareHubEmulator to make the device
auto-detectable by the driver.
Signed-off-by: NClemens Werther <clemens.werther@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a device ID for the RT Systems cable used to
program Yaesu VX-8R/VX-8DR handheld radios. It uses the main
FTDI VID instead of the common RT Systems VID.
Signed-off-by: NMajor Hayden <major@mhtx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Instead of "open coding" a DEVICE_ATTR() define, use the
DEVICE_ATTR_WO() macro instead, which does everything properly instead.

This does require a few static functions to be renamed to work properly,
but thanks to a script from Joe Perches, this was easily done.
Reported-by: NJoe Perches <joe@perches.com>
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Valentina Manea <valentina.manea.m@gmail.com>
Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: NJohan Hovold <johan@kernel.org>
Acked-by: NShuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add AIRBUS_DS_P8GR device IDs to ftdi_sio driver.
Signed-off-by: NMax Schulze <max.schulze@posteo.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner.  So the extra GPL text wording
can be removed as it is no longer needed at all.

This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text.  And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.

No copyright headers or other non-license-description text was removed.
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.

Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.

This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add CYPRESS_VID vid and CYPRESS_WICED_BT_USB and CYPRESS_WICED_WL_USB
device IDs to ftdi_sio driver.
Signed-off-by: NJeffrey Chu <jeffrey.chu@cypress.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Remove the broken alt_speed code, and warn when trying to set the line
speed using TIOCSSERIAL and SPD flags.

The use of SPD flags to set the line speed has been deprecated since
v2.1.69 and support for alt_speed (e.g. "warp") has even been removed
from TTY core in v3.10 by commit 6865ff22 ("TTY: do not warn about
setting speed via SPD_*"), effectively breaking all driver
implementations of this except for serial core.

Also remove the verbose and outdated comment on how to set baud rates.

Note that setting a custom divisor will continue to work with the
caveat that 38400 must again be selected every time the divisor is
changed since v2.6.24 and commit 669a6db1 ("USB: ftd_sio: cleanups
and updates for new termios work") which started reporting back the
actual baud rate used.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Simplify TIOCSSERIAL flag logic somewhat.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support for recognition of ARM-USB-TINY(H) devices which
are almost identical to ARM-USB-OCD(H) but lacking separate barrel jack
and serial console.

By suggestion from Johan Hovold it is possible to replace
ftdi_jtag_quirk with a bit more generic construction. Since all
Olimex-ARM debuggers has exactly two ports, we could safely always use
only second port within the debugger family.
Signed-off-by: NAndrey Korolyov <andrey@xdel.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

Commit 557aaa7f ("ft232: support the ASYNC_LOW_LATENCY
flag") enables unprivileged users to set the FTDI latency timer,
but there was a logic flaw that skipped sending the corresponding
USB control message to the device.

Specifically, the device latency timer would not be updated until next
open, something which was later also inadvertently broken by commit
c19db4c9 ("USB: ftdi_sio: set device latency timeout at port
probe").

A recent commit c6dce262 ("USB: serial: ftdi_sio: fix extreme
low-latency setting") disabled the low-latency mode by default so we now
need this fix to allow unprivileged users to again enable it.
Signed-off-by: NAnthony Mallet <anthony.mallet@laas.fr>
[johan: amend commit message]
Fixes: 557aaa7f ("ft232: support the ASYNC_LOW_LATENCY flag")
Fixes: c19db4c9 ("USB: ftdi_sio: set device latency timeout at port probe").
Cc: stable <stable@vger.kernel.org>     # 2.6.31
Signed-off-by: NJohan Hovold <johan@kernel.org>

This development kit has an FT4232 on it with a custom USB VID/PID.
The FT4232 provides four UARTs, but only two are used. The UART 0
is used by the FlashPro5 programmer and UART 2 is connected to the
SmartFusion2 CortexM3 SoC UART port.

Note that the USB VID is registered to Actel according to Linux USB
VID database, but that was acquired by Microsemi.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>