For each RX packet until this patch there only was a debug
print of the HCMD and the offset. This adds also the
sequence number of the packet for easier matching between
what was sent, what came back / was received, and what
got stuck somewhere and was never responded by the FW.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

According to FW methodology, the capability bits should be the only ones
that change per-HW. The API bits should remain constant across different
HWs.
Currently this is not the case with multi-source LAR (API bit 9). Assign
a new capability bit to eventually replace the API bit. Until the API bit
can be deprecated, the driver will check either to enable multi-source
LAR.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If, on a GO, the CSA time event fails to be scheduled, continue the
flow towards mac80211's state machine so it doesn't get stuck, but
report an error later on the post switch which will cause mac80211
to tear down the operation. This ensures nothing gets stuck due to
the scheduling failure.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The return value in iwl_mvm_get_wakeup_status() is a bit unclear in
that it's not obvious that we don't leak fw_status in some cases.
Use fw_status directly with ERR_PTR() and return only it, that way
the compiler has a chance of proving that it's uninitialized (if it
ever is due to new changes.)

Additionally, this removes a smatch warning since smatch couldn't
figure out that fw_status can't, in fact, leak here.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When IWLWIFI_DEBUGFS is not set, we should not unlock the mutex after
calling iwl_mvm_query_wakeup_reasons(), because this function unlocks
it already.  Move the goto out_iterate outside the #ifdef.

Change-Id: I13d86402aecf0eeec44b1abbe2b244fbc706a5eb
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

The code here is a little confusing, the iwl_mvm_te_check_disconnect()
will check that the interface is a station, but going into it after
already having processed the time even end for P2P seems strange at
first look.

Put a switch statement there to distinguish the interface types and
make this more readable.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We previously enabled the smart FIFO (SF) in BSS only after
association.
This cause interrupt latency on P2P on certain devices.
Change the working model to enable the SF all the time and
play with the timeout values based on the association state.
This change was not tested on older firwmares, so make it
happen only on -13.ucode and up.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

More sub system IDs were introduced for the 8260 series.
Add the new sub system IDs so the cards can be recognized.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware was not using the new API, so we don't need to
differentiate between the different stages of this new API.
The main difference here is that most of the hard coded
values are not sent through the command anymore.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The newer devices will enable a new register for this
(DEVICE_SET_NMI_8000B_REG), but the interrupt handler
isn't wired yet.
Keep the old register for now.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When a station goes to sleep, we can't transmit any frame
to it. This means that until that station will wake up, a
queue that is dedicated to this station won't progress at
all. Take this into account when monitoring stuck queues
and don't account for the time the station was asleep.
This allows to mask false positives where the queues are
stuck not because of a bug, but because of the station
being asleep.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows the op_mode to let the transport know that a
queue is currently frozen and that its timer should be
stopped.
When the queue is unfrozen, its timer should be set to
expire after the remainder of the timeout has elapsed.
This can be used when stations go to sleep. When a station
goes to sleep, the op_mode can freeze the timer so that the
queue will never be considered as stuck. When the station
wakes up, the queue will be unfrozen.
This is meant to avoid false positives that would happen if
a buggy station goes to sleep for a very long time. In case
we have a dedicated queue for this station (BA agreement)
and it goes to sleep for a very long time, the queue would
rightfully be stopped during all that time. In this case,
the stuck queue timer could fire and that would be a false
positive.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The Tx statistics weren't updated when using fixed rate for
debugging. Fix this as Tx statistics are useful in this use case.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

RTNL is not taken during CT-kill so regulatory APIs cannot be invoked.
That's fine, since the HW is only brought up to check the temperature
during CT-kill. We don't expect Tx or scanning.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When using IBSS, it's easily possible to exhaust the number
of available stations in the driver, so don't warn on it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we load the firmware for the 8000 B step device, it'll
verify its signature. In the current version of the
hardware, there can be a race between the WiFi firmware
being loaded and the Bluetooth firmware being loaded.

Check that WiFi is authenticated, if not, take ownership
on the authentication machine to make sure that the WiFi
firmware will be authenticated.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New sub system IDs were introduced for the 8260 series.
This patch adds them so new 8260 cards can be recognized.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Make the print a bit more readable.
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the FW returns an invalid channels count in response to an MCC request,
make sure we don't reference invalid indices in the channels array.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When entering D0i3, the MVM mutex cannot be grabbed. This interferes
with the calculation of the number of connected TDLS stations during
the setup of the power cmd.
The goal is to disable power saving for all vifs while any TDLS station
is connected. For this purpose it is enough to keep the pm_enabled
member of all mvmvifs as false. An update of the power state already
occurs when a TDLS station is added/removed, so the values are correctly
updated.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

mvm->fw->dbg_dest_tlv really needs to be under the right
parenthesis.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The functions related to firmware error dump moved. No need
for this unclude anymore.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

New NVM versions in LnP platforms have the lar_enable bits in a different
offset.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

While at it, fix a few checkpatch issues.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This adds BT Coex data to the prph register list.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We don't need to acquire MAC access for each access, it
makes much more sense to keep the MAC access. This speeds
up the Tx DMA stop flow significantly.
Moreover, if one channel can't be stopped, stop the others
but don't poll for them to avoid being stuck there for a
long time.

This solves a situation in which we were stuck in that flow
for way too long with a spinlock held which led to a kernel
panic.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In-order to recognize newer step of the device, the driver
must read the chip_version_id from the AUX bus MISC address
space. This will determine what firmware file will be
loaded.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When we associate we always need to update the quotas. This
fixes a bug for cases in which quotas weren't udapted after
association.
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enable this feature only if the firmware advertises support
for it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares support this API.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firwmares have this new API.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This new firmware will come out soon.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When moving to the D3 FW give it the valid MCC from the D0 FW. When
returning from D3 to D0, query the D3 FW for the latest MCC, as
it might have changed internally. This MCC will be replayed to the D0 FW
when it boots.
Signed-off-by: NJonathan Doron <jonathanx.doron@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When booting the card, check for a dedicated regulatory ACPI entry. If
such exists, read it and give the information to FW with the appropriate
source.
Signed-off-by: NJonathan Doron <jonathanx.doron@intel.com>
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For some configurations, the driver should get the MAC
address from the hardware registers and not from the
regular locations. Since the parsing of the MAC address
is the same regardless of its source, continue the regular
code path (parsing) after we read the registers.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This module parameter is useful for debugging NVM and LAR related issues.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Starting from family 8000 B0 step the radio_cfg parameters
and the get_sku parameters moved from SW section to PHY_SKU section.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

11ac depends on 11n, so disable it if 11n is disabled.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>