Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 15 11月, 2012 1 次提交
  3. 10 11月, 2012 1 次提交
  5. 23 10月, 2012 4 次提交
  7. 22 10月, 2012 4 次提交
  9. 17 10月, 2012 1 次提交
    • D
      regmap: select REGMAP if REGMAP_MMIO and REGMAP_IRQ enabled · 5784ee4d
      由 Dong Aisheng 提交于 
      The regmap_mmio and regmap_irq depend on regmap core, if not select,
we may not compile regmap core and meet compiling errors as follows
if REGMAP_MMIO is selected by client drivers:
drivers/mfd/syscon.c:94:15: error: variable 'syscon_regmap_config' has initializer but incomplete type
drivers/mfd/syscon.c:95:2: error: unknown field 'reg_bits' specified in initializer
drivers/mfd/syscon.c:95:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:95:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c:96:2: error: unknown field 'val_bits' specified in initializer
drivers/mfd/syscon.c:96:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:96:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c:97:2: error: unknown field 'reg_stride' specified in initializer
drivers/mfd/syscon.c:97:2: warning: excess elements in struct initializer [enabled by default]
drivers/mfd/syscon.c:97:2: warning: (near initialization for 'syscon_regmap_config') [enabled by default]
drivers/mfd/syscon.c: In function 'syscon_probe':
drivers/mfd/syscon.c:124:2: error: invalid use of undefined type 'struct regmap_config'
drivers/mfd/syscon.c:125:2: error: implicit declaration of function 'devm_regmap_init_mmio' [-Werror=implicit-function-declaration]
drivers/mfd/syscon.c:125:17: warning: assignment makes pointer from integer without a cast [enabled by default]
cc1: some warnings being treated as errors

drivers/mfd/Kconfig:
config MFD_SYSCON
        bool "System Controller Register R/W Based on Regmap"
	depends on OF
	select REGMAP_MMIO
	help
	  Select this option to enable accessing system control registers
	    via regmap.
Signed-off-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
      5784ee4d
  11. 09 10月, 2012 2 次提交
    • W
      memory-hotplug: update memory block's state and notify userspace · e90bdb7f
      由 Wen Congyang 提交于 
      remove_memory() will be called when hot removing a memory device.  But
even if offlining memory, we cannot notice it.  So the patch updates the
memory block's state and sends notification to userspace.

Additionally, the memory device may contain more than one memory block.
If the memory block has been offlined, __offline_pages() will fail.  So we
should try to offline one memory block at a time.

Thus remove_memory() also check each memory block's state.  So there is no
need to check the memory block's state before calling remove_memory().
Signed-off-by: NWen Congyang <wency@cn.fujitsu.com>
Signed-off-by: NYasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      e90bdb7f
    • W
      memory-hotplug: preparation to notify memory block's state at memory hot remove · a16cee10
      由 Wen Congyang 提交于 
      remove_memory() is called in two cases:
1. echo offline >/sys/devices/system/memory/memoryXX/state
2. hot remove a memory device

In the 1st case, the memory block's state is changed and the notification
that memory block's state changed is sent to userland after calling
remove_memory().  So user can notice memory block is changed.

But in the 2nd case, the memory block's state is not changed and the
notification is not also sent to userspcae even if calling
remove_memory().  So user cannot notice memory block is changed.

For adding the notification at memory hot remove, the patch just prepare
as follows:
1st case uses offline_pages() for offlining memory.
2nd case uses remove_memory() for offlining memory and changing memory block's
    state and notifing the information.

The patch does not implement notification to remove_memory().
Signed-off-by: NWen Congyang <wency@cn.fujitsu.com>
Signed-off-by: NYasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Jiang Liu <liuj97@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      a16cee10
  13. 05 10月, 2012 1 次提交
  15. 04 10月, 2012 1 次提交
    • L
      firmware: teach the kernel to load firmware files directly from the filesystem · abb139e7
      由 Linus Torvalds 提交于 
      This is a first step in allowing people to by-pass udev for loading
device firmware.  Current versions of udev will deadlock (causing us to
block for the 30 second timeout) under some circumstances if the
firmware is loaded as part of the module initialization path, and this
is causing problems for media drivers in particular.

The current patch hardcodes the firmware path that udev uses by default,
and will fall back to the legacy udev mode if the firmware cannot be
found there.  We'd like to add support for both configuring the paths
and the fallback behaviour, but in the meantime this hopefully fixes the
immediate problem, while also giving us a way forward.

[ v2: Some VFS layer interface cleanups suggested by Al Viro ]
[ v3: use the default udev paths suggested by Kay Sievers ]
Suggested-by: NIvan Kalvachev <ikalvachev@gmail.com>
Acked-by: NGreg KH <gregkh@linuxfoundation.org>
Acked-by: NAl Viro <viro@zeniv.linux.org.uk>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kay Sievers <kay@redhat.com>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      abb139e7
  17. 02 10月, 2012 1 次提交
  19. 27 9月, 2012 1 次提交
  21. 25 9月, 2012 1 次提交
  23. 23 9月, 2012 1 次提交
    • K
      PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2 · 6f3c77b0
      由 Kevin Hilman 提交于 
      There are several drivers where the return value of
pm_runtime_get_sync() is used to decide whether or not it is safe to
access hardware and that don't provide .suspend() callbacks for system
suspend (but may use late/noirq callbacks.)  If such a driver happens
to call pm_runtime_get_sync() during system suspend, after the core
has disabled runtime PM, it will get the error code and will decide
that the hardware should not be accessed, although this may be a wrong
conclusion, depending on the state of the device when runtime PM was
disabled.

Drivers might work around this problem by using a test like:

   ret = pm_runtime_get_sync(dev);
   if (!ret || (ret == -EACCES && driver_private_data(dev)->suspended)) {
      /* access hardware */
   }

where driver_private_data(dev)->suspended is a flag set by the
driver's .suspend() method (that would have to be added for this
purpose).  However, that potentially would need to be done by multiple
drivers which means quite a lot of duplicated code and bloat.

To avoid that we can use the observation that the core sets
dev->power.is_suspended before disabling runtime PM and use that
instead of the driver's private flag.  Still, potentially many drivers
would need to repeat that same check in quite a few places, so it's
better to let the core do it.

Then we can be a bit smarter and check whether or not runtime PM was
disabled by the core only (disable_depth == 1) or by someone else in
addition to the core (disable_depth > 1).  In the former case
rpm_resume() can return 1 if the runtime PM status is RPM_ACTIVE,
because it means the device was active when the core disabled runtime
PM.  In the latter case it should still return -EACCES, because it
isn't clear why runtime PM has been disabled.

Tested on AM3730/Beagle-xM where a wakeup IRQ firing during the late
suspend phase triggers runtime PM activity in the I2C driver since the
wakeup IRQ is on an I2C-connected PMIC.

[rjw: Modified whitespace to follow the file's convention.]
Signed-off-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      6f3c77b0
  25. 21 9月, 2012 1 次提交
  27. 20 9月, 2012 1 次提交
    • A
      PM: Prevent runtime suspend during system resume · 88d26136
      由 Alan Stern 提交于 
      This patch (as1591) moves the pm_runtime_get_noresume() and
pm_runtime_put_sync() calls from __device_suspend() and
device_resume() to device_prepare() and device_complete() in the PM
core.

The reason for doing this is to make sure that parent devices remain
at full power (i.e., don't go into runtime suspend) while their
children are being resumed from a system sleep.

The PCI core already contained equivalent code to serve the same
purpose.  The patch removes the duplicated code, since it is no longer
needed.  One of the comments from the PCI core gets moved into the PM
core, and a second comment is added to explain whe the _get_noresume
and _put_sync calls are present.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      88d26136
  29. 19 9月, 2012 2 次提交
  31. 17 9月, 2012 3 次提交
  33. 11 9月, 2012 1 次提交
  35. 10 9月, 2012 1 次提交
  37. 09 9月, 2012 1 次提交
  39. 07 9月, 2012 5 次提交
  41. 04 9月, 2012 6 次提交
    • R
      PM / Domains: Operations related to cpuidle using domain names · 74a2799a
      由 Rafael J. Wysocki 提交于 
      Make it possible to use domain names in operations connecting cpuidle
to and disconnecting it from a PM domain.  This is useful on
platforms where PM domain objects are organized in such a way that
the names of the domains are easier to use than the addresses of
those objects.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      74a2799a
    • R
      PM / Domains: Document cpuidle-related functions and change their names · 40114447
      由 Rafael J. Wysocki 提交于 
      The names of the cpuidle-related functions in
drivers/base/power/domain.c are inconsistent with the names of the
other exported functions in that file (the "pm_" prefix is missing
from them) and they are missing kerneldoc comments.

Fix that by adding the missing "pm_" prefix to the names of those
functions and add kerneldoc comments documenting them.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      40114447
    • R
      PM / Domains: Add power-on function using names to identify domains · 8bc0251d
      由 Rafael J. Wysocki 提交于 
      It sometimes is necessary to turn on a given PM domain when only
the name of it is known and the domain pointer is not readily
available.  For this reason, add a new helper function,
pm_genpd_name_poweron(), allowing the caller to turn on a PM domain
using its name for identification.  To avoid code duplication,
move the domain lookup code to a separate function.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      8bc0251d
    • R
      PM / Domains: Make it possible to use names when adding subdomains · fb7268be
      由 Rafael J. Wysocki 提交于 
      Add a new helper function, pm_genpd_add_subdomain_names(), allowing
the caller to add a subdomain to a generic PM domain using names for
domain identification (both domains have to be initialized before).

This function is useful for adding subdomains to PM domains whose
representations are stored in tables, when the caller doesn't know
the indices of the domain to add the subdomain to and of the
subdomain itself, but it knows the domains' names.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      fb7268be
    • R
      PM / Domains: Make it possible to use domain names when adding devices · b5abb085
      由 Rafael J. Wysocki 提交于 
      Add a new helper function __pm_genpd_name_add_device() allowing
a device to be added to a (registered) generic PM domain identified
by name.  Add a wrapper around it, pm_genpd_name_add_device(),
passing NULL as the last argument and reorganize pm_domains.h for the
new functions to be defined consistently with the existing ones.

These functions are useful for adding devices to PM domains whose
representations are stored in tables, when the caller doesn't know
the index of the domain to add the device to, but it knows the
domain's name.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      b5abb085
    • R
      PM: Do not use the syscore flag for runtime PM · feb70af0
      由 Rafael J. Wysocki 提交于 
      The syscore device PM flag used to mark the devices (belonging to
PM domains) that should never be turned off, except for the system
core (syscore) suspend/hibernation and resume stages, need not be
accessed by the runtime PM core functions, because all of the devices
it is set for need to be marked as "irq safe" anyway and are
protected from being turned off by runtime PM by ensuring that their
usage counters are always set.

For this reason, make the syscore flag system-wide PM-specific
and simplify the code used for manipulating it, because it need not
acquire the device's power.lock any more.
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
      feb70af0