Distributed Switch Architecture is a protocol for managing hardware
switch chips.  It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.

The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:

	+-----------+       +-----------+
	|           | RGMII |           |
	|           +-------+           +------ 1000baseT MDI ("WAN")
	|           |       |  6-port   +------ 1000baseT MDI ("LAN1")
	|    CPU    |       |  ethernet +------ 1000baseT MDI ("LAN2")
	|           |MIImgmt|  switch   +------ 1000baseT MDI ("LAN3")
	|           +-------+  w/5 PHYs +------ 1000baseT MDI ("LAN4")
	|           |       |           |
	+-----------+       +-----------+

The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.

This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.

(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one.  The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Tested-by: NNicolas Pitre <nico@marvell.com>
Tested-by: NByron Bradley <byron.bbradley@gmail.com>
Tested-by: NTim Ellis <tim.ellis@mac.com>
Tested-by: NPeter van Valderen <linux@ddcrew.com>
Tested-by: NDirk Teurlings <dirk@upexia.nl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRemi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function is huge and included at least once in every VLAN acceleration
capable driver. Uninline it; to avoid having drivers depend on the VLAN
module, the function is always built in statically when VLAN is enabled.

With all VLAN acceleration capable drivers that build on x86_64 enabled,
this results in:

   text    data     bss     dec     hex filename
6515227  854044  343968 7713239  75b1d7 vmlinux.inlined
6505637  854044  343968 7703649  758c61 vmlinux.uninlined
----------------------------------------------------------
  -9590
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the CAN core functionality but no protocols or drivers.
No protocol implementations are included here.  They come as separate
patches.  Protocol numbers are already in include/linux/can.h.
Signed-off-by: NOliver Hartkopp <oliver.hartkopp@volkswagen.de>
Signed-off-by: NUrs Thuermann <urs.thuermann@volkswagen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patchset moves non-filesystem interfaces of v9fs from fs/9p to net/9p.
It moves the transport, packet marshalling and connection layers to net/9p
leaving only the VFS related files in fs/9p.  This work is being done in
preparation for in-kernel 9p servers as well as alternate 9p clients (other
than VFS).
Signed-off-by: NLatchesar Ionkov <lucho@ionkov.net>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

Since there is no Kconfig variable RXRPC anywhere in the tree, and the
variable AF_RXRPC performs exactly the same function, remove the
reference to CONFIG_RXRPC from net/Makefile.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RF kill patch that provides infrastructure for implementing
switches controlling radio states on various network and other cards.

[dtor@insightbb.com: address review comments]
[akpm@linux-foundation.org: cleanups, build fixes]
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add mac80211, the IEEE 802.11 software MAC layer.
Signed-off-by: NJiri Benc <jbenc@suse.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Provide AF_RXRPC sockets that can be used to talk to AFS servers, or serve
answers to AFS clients.  KerberosIV security is fully supported.  The patches
and some example test programs can be found in:

	http://people.redhat.com/~dhowells/rxrpc/

This will eventually replace the old implementation of kernel-only RxRPC
currently resident in net/rxrpc/.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refactors the wireless Kconfig all over and already
introduces net/wireless/Kconfig with just the WEXT bit for now,
the cfg80211 patch will add to that as well.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add rewritten IUCV base code to net/iucv.
Signed-off-by: NFrank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new kernel subsystem, NetLabel, to provide explicit packet
labeling services (CIPSO, RIPSO, etc.) to LSM developers.  NetLabel is
designed to work in conjunction with a LSM to intercept and decode
security labels on incoming network packets as well as ensure that
outgoing network packets are labeled according to the security
mechanism employed by the LSM.  The NetLabel subsystem is configured
through a Generic NETLINK interface described in the header files
included in this patch.
Signed-off-by: NPaul Moore <paul.moore@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TIPC (Transparent Inter Process Communication) is a protocol designed for
intra cluster communication. For more information see
http://tipc.sourceforge.netSigned-off-by: NPer Liden <per.liden@nospam.ericsson.com>

Staticaly linked nf_conntrack_ipv4 requires nf_conntrack. but currently
nf_conntrack is linked after it. This changes the order of ipv4 and netfilter
to fix this.
Signed-off-by: NKrzysztof Oledzki <olenf@ans.pl>
Signed-off-by: NYasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Development to this point was done on a subversion repository at:

http://oops.ghostprotocols.net:81/cgi-bin/viewcvs.cgi/dccp-2.6/

This repository will be kept at this site for the foreseable future,
so that interested parties can see the history of this code,
attributions, etc.

If I ever decide to take this offline I'll provide the full history at
some other suitable place.
Signed-off-by: NArnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce "nfnetlink" (netfilter netlink) layer.  This layer is used as
transport layer for all userspace communication of the new upcoming
netfilter subsystems, such as ctnetlink, nfnetlink_queue and some day even
the mythical pkttables ;)
Signed-off-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Contributors:
Host AP contributors
James Ketrenos <jketreno@linux.intel.com>
Francois Romieu <romieu@fr.zoreil.com>
Adrian Bunk <bunk@stusta.de>
Matthew Galgoci <mgalgoci@parcelfarce.linux.th
eplanet.co.uk>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!