Fix regression introduced by commit 796211b7 ("mmc: atmel-mci: add
pdc support and runtime capabilities detection") which removed the need
for CONFIG_MMC_ATMELMCI_DMA but kept the Kconfig-entry as well as the
compile guards around dma_release_channel() in remove(). Consequently,
DMA is always enabled (if supported), but the DMA-channel is not
released on module unload unless the DMA-config option is selected.

Remove the no longer used CONFIG_MMC_ATMELMCI_DMA option completely.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

Earlier, atmel-mci was adapted to make use of the peripheral DMA
controller (PDC), in case normal DMA wouldn't work.
( http://comments.gmane.org/gmane.linux.kernel.mmc/9403 )

This works OK on ARM platforms (AT91), but it broke the driver
for AVR32, the AP700x.  Although the MCI has PDC support, the
connection is not done for AVR chips.

This patch makes the use of PDC depend on !CONFIG_AVR32.
Signed-off-by: NHein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: NChris Ball <cjb@laptop.org>

After the latest changes to atmel-mci, it could not be used with
DMA on the AVR32 platform. This patch will allow to use DMA again
and it will avoid access to MCI register ATMCI_DMA.

Even if the IP version is lower than v3xx and doesn't have the DMA
configuration register, DMA transfers can be used with a different
controller than the Atmel AHB DMA one. For instance, some AVR chips
use the Synopsys DesignWare AHB DMA controller.
Signed-off-by: NHein Tibosch <hein_tibosch@yahoo.es>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Even if the datasheet says that the not busy flag has to be used only
for write operations, it's false except for version lesser than v2xx.

Not waiting on the not busy flag for read operations can cause the
controller to hang-up during the initialization of some SD cards
with DMA after the first CMD6 -- the next command is sent too early.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org> [3.5, 3.6]
Signed-off-by: NChris Ball <cjb@laptop.org>

Correct spelling typo in drivers/mmc
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Modify clock division displaying in debugfs for matching
the new CLKDIV,CLKODD user interface arrangement.
Is using the has_odd_clk_div property to choose the proper format.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Setting host->data to NULL is incorrect sequence in STATE_SENDING_STOP
state of FSM: This early setting leads to the skip of dma_unmap_sg()
in atmci_dma_cleanup() which is a bug.

Idea taken from dw_mmc by Seungwon Jeon.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The use of DMA slave config operation requires that the burst size
(aka chunk size) is specified through this interface.
Modify atmel-mci slave driver to use this specification on its side.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The data timeout timer was configured after mmc_add_host call. So, with bad
timings, it was possible to have a mmc request causing mod_timer call on a
non setup timer.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Fix mci IP bugs and endianness issue.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The state machine use in atmel-mci can't work with old IP versions
(< 0x200).  This patch allows to have a common state machine for all
versions in order to remove at91-mci driver only used for old versions.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

First mci IPs (mainly on rm9200 and 9261) don't have the r/w proof
capability.  The driver didn't work correctly without this capability
in PDC mode because of the double buffer switch which is too slow
even if we stop the transfer to perform this switch.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add an odd clock divider capability available from v5xx. It also involves
changing the clock divider calculation, and changing the switch-case
statement to use top-down fallthrough.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The HSMCI operates at a rate of up to Master Clock divided by two.
Moreover previous calculation can cause overflows and so wrong
timeouts.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add inline wrappers for device_prep_slave_sg() and device_prep_dma_cyclic()
interfaces to hide new parameter from current users of affected interfaces.
Convert current users to use new wrappers instead of direct calls.
Suggested by Russell King [https://lkml.org/lkml/2012/2/3/269].
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Some callbacks are set too early -- i.e. we can have dma capabilities but
we can't get a dma channel. So wait to get the dma channel before setting
callbacks and change logs consequently.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
[Should be applied to 3.2-stable.]
Cc: <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

There are few existing user drivers of dw_dmac. They will break as soon as we
remove unused fields from struct dw_dma_slave. This patch focuses to fix these
user drivers to use dma_slave_config() routine.
Signed-off-by: NViresh Kumar <viresh.kumar@st.com>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

Sometimes a software reset is needed. Then some registers are saved and
restored but the interrupt mask register is missing. It causes issues
with sdio devices whose interrupts are masked after reset.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

fixup usage of dma direction by introducing dma_transfer_direction,
this patch moves mmc drivers to use new enum

Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NVinod Koul <vinod.koul@linux.intel.com>

This patch fixes a potential issue about PDC interrupts. For example we
have a ENDRX pending interrupt and a RXBUFF pending interrupt. We have
received the RXBUFF interrupt but the transfer is not finished (so we
didn't have time to give a new buffer to the PDC controller). Then we
will compute ENDRX interrupt and we will give a new buffer to the PDC
controller, just after we will compute the RXBUFF interrupt and give
one or two new buffers to the PDC controller but we are not sure that
the first buffer given has been filled. So in this situation we may
have "lost" one sg buffer. It's the same for transmission.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Assuming that a sg buffer size is a page size is false so use sg_dma_len.
A 4096 bytes can be required with two 2048-bytes sg buffer.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Rename atmci_start_command() to atmci_send_command() which is more
appropriate; atmci_start_command suggests we're sending a start command.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add pdc support for atmel-mci. It makes at91-mci driver useless because it
was only used for the old atmel MCI core which has pdc but no dma support.
To allow removing at91-mci, the capabilities of the MCI core are detected
at runtime -- then the driver will use pio, pdc or dma transfers.
Warning: at91rm9200 is not supported, to support it we need to use swab32
on data but I have no board to test it.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Change atmci_readl and atmci_writel macros: remove string concatenation.
We can use these macros with registers which are not prefixed by ATMCI_.
This is the case if we want to write PDC registers which are common to
several devices so they are not prefixed with ATMCI_.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Homogenize namespace to atmci.
Signed-off-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Take care of slots while going to suspend state.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Haavard's e-mail address at Atmel is no longer valid.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NHavard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Use the new dmaengine helpers to make the code more readable.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Fixes the following:
- It is perfectly legal for the dma_map_sg() to return fewer
  entries than were passed in.
- Supply the returned numer of (possibly coalesced) entries to
  the device_pre_slave_sg() function.
- Use the proper original sg_len when unmapping the sglist
  in the error path.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

As established for the MMCI, it is proper to map the DMA buffers
on the DMA engine which is the one actually performing the DMA.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Based on report made by Yauhen in:
"MMC: Fix multiblock SDIO transfers in AT91 MCI" patch,
I report those changes to the brother driver: atmel-mci.

So, this patch sets SDIO transfer types: SDIO block and SDIO byte
transfers instead of using ordinary MMC block transfers.
It is checking opcode for SDIO CMD53 and setting transfer
type in MCI_CMDR register properly.
Reported-by: NYauhen Kharuzhy <yauhen.kharuzhy@promwad.com>
Cc: <stable@kernel.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

We have deprecated the distinction between hardware and physical
segments in the block layer.  Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChris Ball <cjb@laptop.org>