Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 18 2月, 2006 17 次提交
  3. 17 2月, 2006 4 次提交
    • D
      [PATCH] wireless/atmel: fix Open System authentication process bugs · 73451379
      由 Dan Williams 提交于 
      This patch fixes a number of bugs in the authentication process:

1) When falling back to Shared Key authentication mode from Open System,
a missing 'return' would cause the auth request to be sent, but would
drop the card into Management Error state.  When falling back, the
driver should also indicate that it is switching to Shared Key mode by
setting exclude_unencrypted.

2) Initial authentication modes were apparently wrong in some cases,
causing the driver to attempt Shared Key authentication mode when in
fact the access point didn't support that mode or even had WEP disabled.
The driver should set the correct initial authentication mode based on
wep_is_on and exclude_unencrypted.

3) Authentication response packets from the access point in Open System
mode were getting ignored because the driver was expecting the sequence
number of a Shared Key mode response.  The patch separates the OS and SK
mode handling to provide the correct behavior.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      73451379
    • D
      [PATCH] wireless/atmel: fix setting TX key only in ENCODEEXT · 0d467502
      由 Dan Williams 提交于 
      The previous patch that added ENCODEEXT and AUTH support to the atmel
driver contained a slight error which would cause just setting the TX
key index to also set the encryption key again.  This patch allows any
combination of setting the TX key index and setting an encryption key.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
      0d467502
    • F
      sis190: early setting of the pci driver private data · 10487fbd
      由 Francois Romieu 提交于 
      Below this point, the error path will proceed through
sis190_release_board(). It will happily oops if
pci_set_drvdata() has not been issued.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
      10487fbd
    • R
      [MMC] mmci: allow small data transfers · 0425a142
      由 Russell King 提交于 
      If a data transfer is small (less than a FIFO size) we would
hang waiting for the data to be read due to the PIO interrupt
not occuring.  We allowed for this in our PIO interrupt handler,
but not when setting up a data transfer.

Apply the "fix" when setting up a data transfer as well.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
      0425a142
  5. 16 2月, 2006 3 次提交
    • A
      [PATCH] ide: touch softlockup detector during pio · 651c29a1
      由 Andrew Morton 提交于 
      We're getting some softlockup false positives during heavy PIO operations.  So
poke the lockup detector.

Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      651c29a1
    • C
      [PATCH] neofb: avoid resetting display config on unblank (v2) · 9f672004
      由 Christian Trefzer 提交于 
      There were two mistakes in the register-read-on-(un)blank approach.

- First, without proper register (un)locking the value read back will always
  be zero, and this is what I missed entirely until just now.  Due to this,
  the logic could not be verified at all and I tried some bogus checks which
  are completely stupid.

- Second, the LCD status bit will always be set to zero when the backlight
  has been turned off.  Reading the value back during unblank will disable the
  LCD unconditionally, regardless of the state it is supposed to be in, since
  we set it to zero beforehand.

So this is what we do now:

- create a new variable in struct neofb_par, and use that to determine
  whether to read back registers (initialized to true)

- before actually blanking the screen, read back the register to sense any
  possible change made through Fn key combo

- use proper neoUnlock() / neoLock() to actually read something

- every call to neofb_blank() determines if we read back next time: blanking
  disables readback, unblanking (FB_BLANK_UNBLANK) enables it

This should give us a nice and clean state machine.  Has been thoroughly
tested on a Dell Latitude CPiA / NM220 Chip docked to a C/Dock2 with attached
CRT in all possible combinations of LCD/CRT on/off.  I changed the config via
Fn key, let the console blank, unblanked by keypress - works flawlessly.
Signed-off-by: NChristian Trefzer <ctrefzer@gmx.de>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
      9f672004
    • J
      [IA64] remove obsolete corporate address · d3454344
      由 Jes Sorensen 提交于 
      Remove obsolete SGI address
Signed-off-by: NJes Sorensen <jes@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>
      d3454344
  7. 15 2月, 2006 16 次提交