The new error flags are supported by the bnx2x FW.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The changes were mostly made to enable back-to-back data flow with dcb.
Other changes were simply deemed as a better 'clean' initial configuration.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reduces sparse warnings in the bnx2x code,
mostly by changing functions into static and changing
initialization of structures.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We've revised driver prints, changing the mask of existing prints
to allow better control over the debug messages, added prints to
error scenarios, removed unnecessary prints and corrected some spelling.
Please note that this patch contains lines with over 80 characters,
as string messages were kept in a single line.
Signed-off-by: NMerav Sicron <meravs@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In flex10 mode the number of vlan slots supported is halved.
Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAjit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __netif_subqueue_stopped() just does the following:

        struct netdev_queue *txq = netdev_get_tx_queue(dev, queue_index);
        return netif_tx_queue_stopped(txq);

and since we already have the txq in scope, we can just call that
directly in this case.
Suggested-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

This change makes it so that we always write the DMA address for the skb
itself on the same tx_buffer struct that the skb is written on.  This way
we don't need the MAPPED_AS_PAGE flag and we always know it will be the
first DMA value that we will have to unmap.

In addition I have found an issue in which we were leaking a DMA mapping if
the value happened to be 0 which is possible on some platforms.  In order
to resolve that I have updated the transmit path to use the length instead
of the DMA mapping in order to determine if a mapping is actually present.

One other tweak in this patch is that it only writes the olinfo information
on the first descriptor.  As it turns out it isn't necessary to write it
for anything but the first descriptor so there is no need to carry it
forward.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This commit brings the author email address macros up to date for four
modules in the PTP Hardware Clock subsystem.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that gso_segs and bytecount are written to the ring
sooner.  This helps to simplify the logic for the two since segmentation
offloads can now update them within their own function.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of keeping a local copy of the skb on the stack for as long as long
as we do it makes sense to instead just place it on the first tx_buffer
structure so that we can save space on the stack and avoid unnecessary
read/write operations copying the pointer out of the stack and onto the
ring later.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A separate value was added to track Tx completions in order to determine if
the Tx unit was hung.  However we can do the same thing using the number of
packets completed without having to add another stat to the Tx ring.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it more likely that the descriptor flags setup will use
cmov instructions instead of conditional jumps when setting up the flags.
The advantage to this is that the code should just flow a bit more
smoothly.

To do this it is necessary to set the TX_FLAGS_CSUM bit in tx_flags when
doing TSO so that we also do the checksum in addition to the segmentation
offload.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes certain that any packet we attempt to transmit will meet
minimum size requirements for the hardware.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to just cleanup the logic in ixgbe_change_mtu since we
are making it unnecessarily complex due to a workaround required for 82599
when SR-IOV is enabled.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch replaces the existing Rx hot-path in the ixgbe driver with a new
implementation that is based on performing a double buffered receive.  The
ixgbe driver already had something similar in place for its' packet split
path, however in that case we were still receiving the header for the
packet into the sk_buff.  The big change here is the entire receive path
will receive into pages only, and then pull the header out of the page and
copy it into the sk_buff data.  There are several motivations behind this
approach.

First, this allows us to avoid several cache misses as we were taking a
set of cache misses for allocating the sk_buff and then another set for
receiving data into the sk_buff.  We are able to avoid these misses on
receive now as we allocate the sk_buff when data is available.

Second we are able to see a considerable performance gain when an IOMMU is
enabled because we are no longer unmapping every buffer on receive.
Instead we can delay the unmap until we are unable to use the page, and
instead we can simply call sync_single_range on the half of the page that
contains new data.

Finally we are able to drop a considerable amount of code from the driver
as we no longer have to support 2 different receive modes, packet split and
one buffer.  This allows us to optimize the Rx path further since less
branching is required.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This allows the NIC to receive all frames available, including
those with bad FCS, ethernet control frames, and more.

Tested by sending frames with bad FCS.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Including bad FCS, used generate frames with bad FCS
to test other system's handling of RX of bad packets.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This allows the NIC to receive all frames available, including
those with bad FCS, un-matched vlans, ethernet control frames,
and more.

Tested by sending frames with bad FCS.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Including bad FCS, used generate frames with bad FCS
to test other system's handling of RX of bad packets.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support to configure the STMMAC ethernet driver via
device-tree instead of platform_data.

Currently, only the properties needed on SPEAr600 are provided. All
other properties should be added once needed on other platforms.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the datatype of "ip_addr" to __be32 as 'ip' should be in
big endian format.

Adapter needs "ip address" in big endian format stored at lower 32bit
of req.word[1]. netxen_config_ipaddr() now receives 'ip' in big endian
format. To satisfy adapter's need, use memcpy() to copy byte by byte
of 'ip' into lower 32bit of req.word[1].

Mac address and serial number of adapter need to be in little endian format.
Change the data type of the related  variables to __le32 / __le64 or cast it
explicitly to __le32 / __le64 depending upon the requirement.
Signed-off-by: NSantosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch removes unused stats member in pxa168 network driver.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When cycling the interface down and up, bnx2x_init_firmware() knows that
the firmware is already loaded, but nevertheless it allocates certain
arrays anew (init_data, init_ops, init_ops_offsets, iro_arr). The old
arrays are leaked.

Fix the leaks by returning early if the firmware was already loaded.
Because if the firmware is loaded, so are the arrays.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the requested firmware is deemed corrupt and then released, reset the
pointer to NULL in order to avoid double-freeing it in
bnx2x_release_firmware() or dereferencing it in bnx2x_init_firmware().
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were two version strings, and neither one was being used.
Also in the same proximity were some unused #define that were
left over from the past.  Delete them all.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Add support for byte queue limits (BQL), based on the similar
modifications made to intel/igb/igb_main.c from Eric Dumazet
in commit bdbc0631
	"igb: Add support for byte queue limits."

A local variable for tx_queue->qindex was introduced in
gfar_clean_tx_ring, since it is now used often enough to warrant it,
and it cleans up the readability somewhat as well.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Disabling and enabling DCB can cause FCoE hardware initialization to
occur on the incorrect traffic class when the up2tc mapping has not
yet been reconfigured.

Fix this by using the DCB configuration maps that are correct
and will be pushed at mqprio after DCB driver setup completes
successfully.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There was a race condition in the reset path where the RX buffer
could become corrupted during Fdir configuration.This is due to
a HW bug.The fix right now is to lock the buffer while we do the
fdir configuration.Since we were using similar workaround for another bug,
I moved the existing code to a function and reused it.HW team also recommended
that IXGBE_MAX_SECRX_POLL value be changed from 30 to 40.The erratum for this
bug will be published in the next release 82599 Spec Update
Signed-off-by: NAtita Shirwaikar <atita.shirwaikar@intel.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

using the form min((int)var, ver)) is replaced by min_t(int, ...)
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is clearly a typeo where we are not checking the return value from
get_link_capabilities but should.  This patch corrects that.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There isn't much point in using variables to store the values of eitr_low
and eitr_high since they are not user changeable.  As such I am replacing
them with the constants 10 and 20 in order to avoid any confusion on what
the values actually are.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A previous fix had gone though and disabled relaxed ordering for Rx
descriptor read fetching.  This was not necessary as this functions
correctly and has no ill effects on the system.

In addition several of the defines used for the DCA control registers were
incorrect in that they indicated descriptor effects when they actually had
an impact on either data or header write back.  As such I have update these
to correctly reflect either DATA or HEAD.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the current logging styles.

Remove unnecessary _DEBUG_DRIVER_ and PFX, use pr_debug.
Coalesce format.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it a bit easier to do the loopback frame creating and
testing.  Previously we were doing an and to drop the last bit, and then
dividing the frame_size by 2 in order to get locations for frame bytes and
testing.  Instead we can simplify it by just shifting the register one bit
to the right and using that for the frame offsets.

This change also replaces all instances of rx_buffer_info with just
rx_buffer since that is closer to the name of the actual structure being
used and can save a few extra characters.

In addition I have updated the logic for cleaning up a test frame so that
we pass an rx_buffer instead of the sk_buff.  The main motivation behind
this is changes that will replace the sk_buff with just a page in the
future.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>