Consolidate the cast type translation, move the passthru path out of
the RCU-guarded section, and use the appropriate rtable helpers when
determining the next-hop address.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The L3 packet descriptor's 'dest_addr' field is used for a different
purpose in RX descriptors. Clean up the hard-coded byte accesses and
try to be more self-documenting.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When
1. an skb has no neighbour, and
2. skb->protocol is not IP[V6],

we select the skb's cast type based on its destination MAC address.

The multicast check is currently restricted to Multicast IP-mapped MACs.
Extend it to also cover non-IP Multicast MACs.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the proper helpers to check for multicast IP addressing, and remove
some ancient Token Ring code.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of assuming that skb->data points to the Ethernet header, use
the right helper and struct to access the Ethertype field.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Once all of qeth_l3_set_rx_mode()'s single-use helpers are folded back
in, the two implementations actually look quite similar. So improve the
readability by converting both set_rx_mode() routines to a common
format.

This also allows us to walk ip_mc_htable just once, instead of three
times.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Be a little more self-documenting, and get rid of OSA_ADDR_LEN.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For adding/removing a MAC address, use just one helper each that
handles both unicast and multicast.
Saves one level of indirection for multicast addresses, while improving
the error reporting for unicast addresses.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of tracking the uc/mc state in each MAC address object, just
check the multicast bit in the address itself.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit "s390/qeth: use ip*_eth_mc_map helpers" removed the last
occurrence of CONFIG_IPV6-dependent code.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of some wrapper indirection, and stop accessing the skb at
hard-coded offsets.
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

atomic_t variables are currently used to implement reference
counters with the following properties:
 - counter is initialized to 1 using atomic_set()
 - a resource is freed upon counter reaching zero
 - once counter reaches zero, its further
   increments aren't allowed
 - counter schema uses basic atomic operations
   (set, inc, inc_not_zero, dec_and_test, etc.)

Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.

The variable qeth_reply.refcnt is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NDavid Windsor <dwindsor@gmail.com>
Reviewed-by: NHans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: NElena Reshetova <elena.reshetova@intel.com>
[jwi: removed the WARN_ONs. Use CONFIG_REFCOUNT_FULL if you care.]
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

atomic_t variables are currently used to implement reference
counters with the following properties:
 - counter is initialized to 1 using atomic_set()
 - a resource is freed upon counter reaching zero
 - once counter reaches zero, its further
   increments aren't allowed
 - counter schema uses basic atomic operations
   (set, inc, inc_not_zero, dec_and_test, etc.)

Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.

The variable lcs_reply.refcnt is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: NKees Cook <keescook@chromium.org>
Reviewed-by: NDavid Windsor <dwindsor@gmail.com>
Reviewed-by: NHans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: NElena Reshetova <elena.reshetova@intel.com>
[jwi: removed the WARN_ONs. Use CONFIG_REFCOUNT_FULL if you care.]
Signed-off-by: NJulian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature/cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - de-inline hash functions to save memory footprint, by Denys Vlasenko

 - Add License information to various files, by Sven Eckelmann (3 patches)

 - Change batman_adv.h from ISC to MIT, by Sven Eckelmann

 - Improve various includes, by Sven Eckelmann (5 patches)

 - Lots of kernel-doc work by Sven Eckelmann (8 patches)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yafang Shao says:

====================
replace tcp_set_state tracepoint with inet_sock_set_state

According to the discussion in the mail thread
https://patchwork.kernel.org/patch/10099243/,
tcp_set_state tracepoint is renamed to inet_sock_set_state tracepoint and is
moved to include/trace/events/sock.h.

With this new tracepoint, we can trace AF_INET/AF_INET6 sock state transitions.
As there's only one single tracepoint for inet, so I didn't create a new trace
file named trace/events/inet_sock.h, and just place it in
include/trace/events/sock.h

Currently TCP/DCCP/SCTP state transitions are traced with this tracepoint.

- Why not more protocol ?
If we really think that anonter protocol should be traced, I will modify the
code to trace it.
I just want to make the code easy and not output useless information.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With changes in inet_ files, SCTP state transitions are traced with
inet_sock_set_state tracepoint.
As SCTP state names, i.e. SCTP_SS_CLOSED, SCTP_SS_ESTABLISHED,
have the same value with TCP state names. So the output info still print
the TCP state names, that makes the code easy.
Signed-off-by: NYafang Shao <laoar.shao@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With changes in inet_ files, DCCP state transitions are traced with
inet_sock_set_state tracepoint.
Signed-off-by: NYafang Shao <laoar.shao@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sk_state_load is only used by AF_INET/AF_INET6, so rename it to
inet_sk_state_load and move it into inet_sock.h.

sk_state_store is removed as it is not used any more.
Signed-off-by: NYafang Shao <laoar.shao@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As sk_state is a common field for struct sock, so the state
transition tracepoint should not be a TCP specific feature.
Currently it traces all AF_INET state transition, so I rename this
tracepoint to inet_sock_set_state tracepoint with some minor changes and move it
into trace/events/sock.h.
We dont need to create a file named trace/events/inet_sock.h for this one single
tracepoint.

Two helpers are introduced to trace sk_state transition
    - void inet_sk_state_store(struct sock *sk, int newstate);
    - void inet_sk_set_state(struct sock *sk, int state);
As trace header should not be included in other header files,
so they are defined in sock.c.

The protocol such as SCTP maybe compiled as a ko, hence export
inet_sk_set_state().
Signed-off-by: NYafang Shao <laoar.shao@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TCP trace events (specifically tcp_set_state), maps emums to symbol
names via __print_symbolic(). But this only works for reading trace events
from the tracefs trace files. If perf or trace-cmd were to record these
events, the event format file does not convert the enum names into numbers,
and you get something like:

__print_symbolic(REC->oldstate,
    { TCP_ESTABLISHED, "TCP_ESTABLISHED" },
    { TCP_SYN_SENT, "TCP_SYN_SENT" },
    { TCP_SYN_RECV, "TCP_SYN_RECV" },
    { TCP_FIN_WAIT1, "TCP_FIN_WAIT1" },
    { TCP_FIN_WAIT2, "TCP_FIN_WAIT2" },
    { TCP_TIME_WAIT, "TCP_TIME_WAIT" },
    { TCP_CLOSE, "TCP_CLOSE" },
    { TCP_CLOSE_WAIT, "TCP_CLOSE_WAIT" },
    { TCP_LAST_ACK, "TCP_LAST_ACK" },
    { TCP_LISTEN, "TCP_LISTEN" },
    { TCP_CLOSING, "TCP_CLOSING" },
    { TCP_NEW_SYN_RECV, "TCP_NEW_SYN_RECV" })

Where trace-cmd and perf do not know the values of those enums.

Use the TRACE_DEFINE_ENUM() macros that will have the trace events convert
the enum strings into their values at system boot. This will allow perf and
trace-cmd to see actual numbers and not enums:

__print_symbolic(REC->oldstate,
    { 1, "TCP_ESTABLISHED" },
    { 2, "TCP_SYN_SENT" },
    { 3, "TCP_SYN_RECV" },
    { 4, "TCP_FIN_WAIT1" },
    { 5, "TCP_FIN_WAIT2" },
    { 6, "TCP_TIME_WAIT" },
    { 7, "TCP_CLOSE" },
    { 8, "TCP_CLOSE_WAIT" },
    { 9, "TCP_LAST_ACK" },
    { 10, "TCP_LISTEN" },
    { 11, "TCP_CLOSING" },
    { 12, "TCP_NEW_SYN_RECV" })
Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NYafang Shao <laoar.shao@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Checking return value with IS_ERROR_OR_NULL
- Added error handling where it was not handled
Signed-off-by: NPrashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If md is NULL, tun_dst must be freed, otherwise it will cause memory
leak.

Fixes: ef7baf5e ("ip6_gre: add ip6 erspan collect_md mode")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If md is NULL, tun_dst must be freed, otherwise it will cause memory
leak.

Fixes: 1a66a836 ("gre: add collect_md mode to ERSPAN tunnel")
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Same as ipv4 code, when ip6erspan_rcv call return PACKET_REJECT, we
should call icmpv6_send to send icmp unreachable message in error path.

Fixes: 5a963eb6 ("ip6_gre: Add ERSPAN native tunnel support")
Acked-by: NWilliam Tu <u9012063@gmail.com>
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When erspan_rcv call return PACKET_REJECT, we shoudn't call ipgre_rcv to
process packets again, instead send icmp unreachable message in error
path.

Fixes: 84e54fe0 ("gre: introduce native tunnel support for ERSPAN")
Acked-by: NWilliam Tu <u9012063@gmail.com>
Cc: William Tu <u9012063@gmail.com>
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pskb_may_pull() can change skb->data, so we need to load ipv6h/ershdr at
the right place.

Fixes: 5a963eb6 ("ip6_gre: Add ERSPAN native tunnel support")
Cc: William Tu <u9012063@gmail.com>
Acked-by: NWilliam Tu <u9012063@gmail.com>
Signed-off-by: NHaishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of yet another custom hex_dump_to_buffer().

The output is slightly changed, i.e. each byte followed by white space.

Note, we don't use print_hex_dump() here since the original code uses
nedev_dbg().
Acked-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
netdevsim: couple of build warning fixes

This series fixes two harmless build warning about a symbol which
should be static and an unused variable.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skip_sw is set but no longer used.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

struct device_type nsim_dev_type created for SR-IOV support
should be static.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add test cases for gretap and ip6gretap, native mode
and external (collect metadata) mode.
Signed-off-by: NWilliam Tu <u9012063@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace sscanf() with mac_pton().
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace sscanf() with mac_pton().
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use
	%pM to print MAC
	mac_pton() to convert it from ASCII to binary format, and
	ether_addr_copy() to copy.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

LTP/udp6_ipsec_vti tests fail when sending large UDP datagrams over
ip6_vti that require fragmentation and the underlying device has an
MTU smaller than 1500 plus some extra space for headers. This happens
because ip6_vti, by default, sets MTU to ETH_DATA_LEN and not updating
it depending on a destination address or link parameter. Further
attempts to send UDP packets may succeed because pmtu gets updated on
ICMPV6_PKT_TOOBIG in vti6_err().

In case the lower device has larger MTU size, e.g. 9000, ip6_vti works
but not using the possible maximum size, output packets have 1500 limit.

The above cases require manual MTU setup after ip6_vti creation. However
ip_vti already updates MTU based on lower device with ip_tunnel_bind_dev().

Here is the example when the lower device MTU is set to 9000:

  # ip a sh ltp_ns_veth2
      ltp_ns_veth2@if7: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 ...
        inet 10.0.0.2/24 scope global ltp_ns_veth2
        inet6 fd00::2/64 scope global

  # ip li add vti6 type vti6 local fd00::2 remote fd00::1
  # ip li show vti6
      vti6@NONE: <POINTOPOINT,NOARP> mtu 1500 ...
        link/tunnel6 fd00::2 peer fd00::1

After the patch:
  # ip li add vti6 type vti6 local fd00::2 remote fd00::1
  # ip li show vti6
      vti6@NONE: <POINTOPOINT,NOARP> mtu 8832 ...
        link/tunnel6 fd00::2 peer fd00::1
Reported-by: NPetr Vorel <pvorel@suse.cz>
Signed-off-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Horman says:

====================
nfp: flower: add Geneve tunnel support

John Hurley says:

This patchset adds support for offloading the encap and decap of Geneve
tunnels to the NFP. In both cases, specifying well known port 6081 is a
requirement for rule offload.

Geneve firmware support has been recently added, so the patchset includes
the reading of a fw symbol that defines a bitmap of newly supported
features. Geneve will only be offloaded if the fw supports it. The new
symbol is added in fw r5646.

Geneve option fields are not supported as either a match or an action due
there current exclussion from TC flower. Because Geneve (as both a match
and action) behaves the same as other udp tunnels such as VXLAN, generic
functions are created that handle both Geneve and VXLAN. It is anticapated
that these functions will be modified to support options in future
patches.

The removal of an unused variable 'tun_dst_mask' is included as a separate
patch here. This does not affect functionality.

Also included are modifications to the test framework to check that the
new encap and decap features are functioning correctly.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Generate rules for the NFP to encapsulate packets in Geneve tunnels. Move
the vxlan action code to generic udp tunnel actions and use core code for
both vxlan and Geneve.

Only support outputting to well known port 6081. Setting tunnel options
is not supported yet.

Only attempt to offload if the fw supports Geneve.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compile Geneve match fields for offloading to the NFP. The addition of
Geneve overflows the 8 bit key_layer field, so apply extended metadata to
the match cmsg allowing up to 32 more key_layer fields.

Rather than adding new Geneve blocks, move the vxlan code to generic ipv4
udp tunnel structs and use these for both vxlan and Geneve.

Matches are only supported when specifically mentioning well known port
6081. Geneve tunnel options are not yet included in the match.

Only offload Geneve if the fw supports it - include check for this.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract the _abi_flower_extra_features symbol from the fw which gives a 64
bit bitmap of new features (on top of the flower base support) that the fw
can offload. Store this bitmap in the priv data associated with each app.
If the symbol does not exist, set the bitmap to 0.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>