Add a Bug sections, indicating preferred mailing method for bug
reports, to Samsung SoC related entries and memory controller drivers.
Signed-off-by: NKrzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220420104708.106738-1-krzysztof.kozlowski@linaro.org'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

HyperFlash devices fail to probe:

    rpc-if-hyperflash rpc-if-hyperflash: probing of hyperbus device failed

In HyperFlash or Octal-SPI Flash mode, the Transfer Data Enable bits
(SPIDE) in the Manual Mode Enable Setting Register (SMENR) are derived
from half of the transfer size, cfr. the rpcif_bits_set() helper
function.  However, rpcif_reg_{read,write}() does not take the bus size
into account, and does not double all Manual Mode Data Register access
sizes when communicating with a HyperFlash or Octal-SPI Flash device.

Fix this, and avoid the back-and-forth conversion between transfer size
and Transfer Data Enable bits, by explicitly storing the transfer size
in struct rpcif, and using that value to determine access size in
rpcif_reg_{read,write}().

Enforce that the "high" Manual Mode Read/Write Data Registers
(SM[RW]DR1) are only used for 8-byte data accesses.
While at it, forbid writing to the Manual Mode Read Data Registers,
as they are read-only.

Fixes: fff53a55 ("memory: renesas-rpc-if: Correct QSPI data transfer in Manual mode")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NKrzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: NLad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/cde9bfacf704c81865f57b15d1b48a4793da4286.1649681476.git.geert+renesas@glider.be
Link: https://lore.kernel.org/r/20220420070526.9367-1-krzysztof.kozlowski@linaro.org'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'at91-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes

AT91 fixes #1 for 5.18:

Only DT fixes. They cover syntax issues as well as features:
- fix dtschema check warnings for DMA channel entries, boolean
  properties and flash names
- sam9g20ek audio clock and regulator description
- sama5d[34]_xplained SPI pinctrl
- align DT with hardware subtleties on sama7g5ek

* tag 'at91-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
  ARM: dts: at91: fix pinctrl phandles
  ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name
  ARM: dts: at91: Describe regulators on at91sam9g20ek
  ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek
  ARM: dts: at91: Fix boolean properties with values
  ARM: dts: at91: use generic node name for dataflash
  ARM: dts: at91: align SPI NOR node name with dtschema
  ARM: dts: at91: sama7g5ek: Align the impedance of the QSPI0's HSIO and PCB lines
  ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines
  ARM: dts: at91: sama7g5: Swap `rx` and `tx` for `i2c` nodes

Link: https://lore.kernel.org/r/20220414143318.26363-1-nicolas.ferre@microchip.comSigned-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'optee-fix-for-v5.18' of git://git.linaro.org/people/jens.wiklander/linux-tee into arm/fixes

OP-TEE fix missing mutex_destroy in probe error handling path

* tag 'optee-fix-for-v5.18' of git://git.linaro.org/people/jens.wiklander/linux-tee:
  tee: optee: add missing mutext_destroy in optee_ffa_probe

Link: https://lore.kernel.org/r/20220413052001.GA49798@jadeSigned-off-by: NArnd Bergmann <arnd@arndb.de>

Merge branch 'v5.18/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux into arm/fixes

* 'v5.18/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
  arm64: dts: meson-sm1-bananapi-m5: fix wrong GPIO pin labeling for CON1
  arm64: dts: remove cpu compatible "arm,armv8" for s4
  arm64: dts: meson: remove CPU opps below 1GHz for SM1 boards
  arm64: dts: meson: remove CPU opps below 1GHz for G12B boards

Link: https://lore.kernel.org/r/1132bd6e-cd29-6e58-1fae-38e074545b25@baylibre.comSigned-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'imx-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 5.18:

- Increase DOMAIN_MAX_CLKS in imx8m-blk-ctrl driver to fix an ISI hang
  on i.MX8MN.
- Fix spi-tx-bus-width on imx8mq-tqma8mq board.
- Fix an SGTL5000 detection issue by moving MCLK pinctrl into SGTL5000
  codec node.
- Fix spi2 pin configuration on imx8mm-venice board.
- Fix SCU clock controller's compatible property for i.MX8QM.
- Fix SAI device compatible for i.MX8MN.
- A couple of fixes from Rob to address issues in boolean properties
  and touchscreen property sizes.
- Fix OTG controller over-current configuration for imx8mm-venice-gw
  boards.
- Fix NULL but dereferenced coccicheck error in imx-weim driver.

* tag 'imx-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
  ARM: dts: imx: Fix boolean properties with values
  ARM: dts: imx8mm-venice-gw{71xx,72xx,73xx}: fix OTG controller OC mode
  arm64: dts: imx8mn: Fix SAI nodes
  arm64: dts: imx8mq-tqma8mq: change the spi-nor tx
  ARM: dts: imx6qdl-apalis: Fix sgtl5000 detection issue
  soc: imx: imx8m-blk-ctrl: Fix IMX8MN_DISPBLK_PD_ISI hang
  arm64: dts: imx8qm: Correct SCU clock controller's compatible property
  arm64: dts: imx8mm-venice: fix spi2 pin configuration
  bus: imx-weim: fix NULL but dereferenced coccicheck error

Link: https://lore.kernel.org/r/20220411024301.GH129381@dragonSigned-off-by: NArnd Bergmann <arnd@arndb.de>

The Gemini defconfig needs to be updated due to DSA driver
Kconfig changes in the v5.18 merge window:
CONFIG_NET_DSA_REALTEK_SMI is now behind
CONFIG_NET_DSA_REALTEK and the desired DSA switch need
to be selected explicitly with
CONFIG_NET_DSA_REALTEK_RTL8366RB.

Take this opportunity to update some other minor config
options:

- CONFIG_MARVELL_PHY moved around because of Kconfig
  changes.

- CONFIG_SENSORS_DRIVETEMP should be selected since is
  regulates the system critical alert temperature on
  some devices, which is nice if it is handled even
  if initramfs or root fails to mount.

Fixes: 319a70a5 ("net: dsa: realtek-smi: move to subdirectory")
Fixes: 765c39a4 ("net: dsa: realtek: convert subdrivers into modules")
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.

It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: NRob Herring <robh@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20220407225254.2178644-1-robh@kernel.org'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: NKrzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20220407143027.294678-1-krzysztof.kozlowski@linaro.org'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.

It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: NRob Herring <robh@kernel.org>
Reviewed-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-arm-msm@vger.kernel.org
Link: https://lore.kernel.org/r/20220407225107.2175958-1-robh@kernel.org'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'ux500-defconfig-soc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/fixes

Defconfig updates for kernel v5.18:

- Refresh defconfig with new and moved options
- Add some new hardware drivers
- Activate battery charging

* tag 'ux500-defconfig-soc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
  ARM: config: u8500: Re-enable AB8500 battery charging
  ARM: config: u8500: Add some common hardware
  ARM: config: Refresh U8500 defconfig

Link: https://lore.kernel.org/r/CACRpkdY+_Go4XNzOh+Rvc24QBnUud2k-S7VQuaH5d-j71_dJog@mail.gmail.comSigned-off-by: NArnd Bergmann <arnd@arndb.de>

Commit bf781869 ("ARM: dts: at91: add pinctrl-{names, 0} for all
gpios") introduces pinctrl phandles for pins used by individual
controllers to avoid failures due to commit 2ab73c6d ("gpio:
Support GPIO controllers without pin-ranges"). For SPI controllers
available on SAMA5D4 and SAMA5D3 some of the pins are defined in
SoC specific dtsi on behalf of pinctrl-0. Adding extra pinctrl phandles
on board specific dts also on behalf of pinctrl-0 overwrite the pinctrl-0
phandle specified in SoC specific dtsi. Thus add the board specific
pinctrl to pinctrl-1.

Fixes: bf781869 ("ARM: dts: at91: add pinctrl-{names, 0} for all gpios")
Depends-on: 5c8b4985 ("ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name")
Reported-by: NAjay Kathat <ajay.kathat@microchip.com>
Co-developed-by: NAjay Kathat <ajay.kathat@microchip.com>
Signed-off-by: NAjay Kathat <ajay.kathat@microchip.com>
Tested-by: NAjay Kathat <ajay.kathat@microchip.com>
Signed-off-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220331141323.194355-2-claudiu.beznea@microchip.com

Pinctrl phandle is for spi1 so rename it to reflect this.
Signed-off-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220331141323.194355-1-claudiu.beznea@microchip.com

The at91sam9g20ek has no software controllable regulators, only some fixed
discrete regulators, but they are there and currently the wm8731 driver
does try to use them. Show the supplies in the DT and map them for the
wm8731 so things start up cleanly.
Signed-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220404102806.581374-3-broonie@kernel.org

The MCLK of the WM8731 on the AT91SAM9G20-EK board is connected to the
PCK0 output of the SoC and is expected to be set to 12MHz. Previously
this was mapped using pre-common clock API calls in the audio machine
driver but the conversion to the common clock framework broke that so
describe things in the DT instead.

Fixes: ff78a189 ("ARM: at91: remove old at91-specific clock driver")
Signed-off-by: NMark Brown <broonie@kernel.org>
Reviewed-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220404102806.581374-2-broonie@kernel.org

Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.

It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: NRob Herring <robh@kernel.org>
Reviewed-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/Yk3leykDEKGBN8rk@robh.at.kernel.org

The node names should be generic, so use "flash" for dataflash nodes and
for cfi-flash.
Suggested-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NKrzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220412105013.249793-1-krzysztof.kozlowski@linaro.org

The node names should be generic and SPI NOR dtschema expects "flash".
Signed-off-by: NKrzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220407143223.295344-1-krzysztof.kozlowski@linaro.org

The impedance of the QSPI PCB lines on the sama7g5ek is 50 Ohms.
Align the output impedance of the QSPI0 HSIOs by setting a medium drive
strength which corresponds to an impedance of 56 Ohms when VDD is in the
3.0V - 3.6V range. The high drive strength setting corresponds to an
output impedance of 42 Ohms on the QSPI0 HSIOs.
Suggested-by: NMihai Sain <mihai.sain@microchip.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220406130505.422042-1-tudor.ambarus@microchip.com

Flexcom3 is used as board console serial. There are no pull-ups on these
lines on the board. This means that if a cable is not connected (that has
pull-ups included), stray characters could appear on the console as the
floating pins voltage levels are interpreted as incoming characters.
To avoid this problem, enable the internal pull-ups on these lines.

Fixes: 7540629e ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220307113827.2419331-1-eugen.hristev@microchip.com

Swap `rx` and `tx` for the `dma-names` property of the `i2c` nodes
in order to maintain consistency across Microchip/Atmel SoC files.
Signed-off-by: NSergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20220310114553.184763-2-sergiu.moga@microchip.com

The labels for lines 61 through 84 on the periphs-banks were offset by 2.
2 lines are missing in the BOOT GPIO lines (contains 14, should be 16)
Added 2 empty entries in BOOT to realigned the rest of GPIO labels
to match the Banana Pi M5 schematics.

(Thanks to Neil Armstrong for the heads up on the position of the missing pins)

Fixes: 976e9201 ("arm64: dts: meson-sm1: add Banana PI BPI-M5 board dts")
Signed-off-by: NGuillaume Giraudon <ggiraudon@prism19.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220411144427.874-1-ggiraudon@prism19.com

The common touchscreen properties are all 32-bit, not 16-bit. These
properties must not be too important as they are all ignored in case of an
error reading them.
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.

It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: NRob Herring <robh@kernel.org>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The GW71xx, GW72xx and GW73xx boards have USB1 routed to a USB OTG
connectors and USB2 routed to a USB hub.

The OTG connector has a over-currently protection with an active-low
pin and the USB1 to HUB connection has no over-current protection (as
the HUB itself implements this for its downstream ports).

Add proper dt nodes to specify the over-current pin polarity for USB1
and disable over-current protection for USB2.

Fixes: 6f30b27c ("arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits")
Cc: stable@vger.kernel.org
Signed-off-by: NTim Harvey <tharvey@gateworks.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The most specific compatible string element should be "fsl,imx8mn-sai"
on i.MX8M Nano, fix it from current "fsl,imx8mm-sai" (two Ms, likely
due to copy-paste error from i.MX8M Mini).

Fixes: 9e986006 ("arm64: dts: imx8mn: Add SAI nodes")
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

This fixes the qspi read command by importing the changes from commit
04aa946d ("arm64: dts: imx8: change the spi-nor tx").

Fixes: b186b8b6 ("arm64: dts: freescale: add initial device tree for TQMa8Mx with i.MX8M")
Signed-off-by: NAlexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

On a custom carrier board with a i.MX6Q Apalis SoM, the sgtl5000 codec
on the SoM is often not detected and the following error message is
seen when the sgtl5000 driver tries to read the ID register:

sgtl5000 1-000a: Error reading chip id -6

The reason for the error is that the MCLK clock is not provided
early enough.

Fix the problem by describing the MCLK pinctrl inside the codec
node instead of placing it inside the audmux pinctrl group.

With this change applied the sgtl5000 is always detected on every boot.

Fixes: 693e3ffa ("ARM: dts: imx6: Add support for Toradex Apalis iMX6Q/D SoM")
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NTim Harvey <tharvey@gateworks.com>
Acked-by: NMax Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The imx8mn clock list for the ISI lists four clocks, but DOMAIN_MAX_CLKS
was set to 3.  Because of this, attempts to enable the fourth clock failed,
threw some splat, and ultimately hung.

Fixes: 7f511d51 ("soc: imx: imx8m-blk-ctrl: add i.MX8MN DISP blk-ctrl")
Signed-off-by: NAdam Ford <aford173@gmail.com>
Reviewed-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

The fsl,scu.txt dt-binding documentation explicitly mentions
that the compatible string should be either "fsl,imx8qm-clock"
or "fsl,imx8qxp-clock", followed by "fsl,scu-clk".  Also, i.MX8qm
SCU clocks and i.MX8qxp SCU clocks are really not the same, so
we have to set the compatible property according to SoC name.
Let's correct the i.MX8qm clock controller's compatible property
from
"fsl,imx8qxp-clk", "fsl,scu-clk"
to
"fsl,imx8qm-clk", "fsl,scu-clk" .

Fixes: f2180be1 ("arm64: dts: imx: add imx8qm common dts file")
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: NLiu Ying <victor.liu@nxp.com>
Signed-off-by: NShawn Guo <shawnguo@kernel.org>

Amlogic s4 device is already applied, but cpu compatible 'arm,armv8'
is only valid for software models, so we remove it.

Fixes: ac4dfd0d ("arm64: dts: add support for S4 based Amlogic AQ222")
Signed-off-by: NXianwei Zhao <xianwei.zhao@amlogic.com>
Reviewed-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220408070901.26446-1-xianwei.zhao@amlogic.com

Reset controller fixes for v5.18

Document the deprecated 'hisi,rst-syscon' device tree property for
hisilicon,hi3660-reset, add an error check to reset deassertion in
reset-rzg2l-usbphy-ctrl, restore transfer error handling in Tegra
reset-bpmp, and document the optional 'resets' device tree property
for socionext,uniphier-reset.

* tag 'reset-fixes-for-v5.18' of git://git.pengutronix.de/pza/linux:
  dt-bindings: reset: Add parent "resets" property as optional
  reset: tegra-bpmp: Restore Handle errors in BPMP response
  reset: renesas: Check return value of reset_control_deassert()
  dt-bindings: reset: document deprecated HiSilicon property

Link: https://lore.kernel.org/r/20220406153337.1265414-1-p.zabel@pengutronix.deSigned-off-by: NArnd Bergmann <arnd@arndb.de>

Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.

It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: NRob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/Yk3m92Sj26/v1mLG@robh.at.kernel.org'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

The common touchscreen properties are all 32-bit, not 16-bit. These
properties must not be too important as they are all ignored in case of an
error reading them.
Signed-off-by: NRob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/Yk3moe6Hz8ELM0iS@robh.at.kernel.org'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.

It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: NRob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/Yk3mR5yae3gCkKhp@robh.at.kernel.org'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.

It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: NRob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/Yk3nShkFzNJaI3/Z@robh.at.kernel.org'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Boolean properties in DT are present or not present and don't take a value.
A property such as 'foo = <0>;' evaluated to true. IOW, the value doesn't
matter.

It may have been intended that 0 values are false, but there is no change
in behavior with this patch.
Signed-off-by: NRob Herring <robh@kernel.org>
Reviewed-by: NClaudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/Yk3leykDEKGBN8rk@robh.at.kernel.org'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Missed the defconfig when removing the board files causing
failures in builds using this defconfig.

Fixes: 28f74201 ("ARM: pxa: remove Intel Imote2 and Stargate 2 boards")
Reported-by: NSudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: NJonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220405135252.10283-1-Jonathan.Cameron@huawei.com'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'memory-controller-drv-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/fixes

Memory controller drivers - fixes for v5.18

Issues in v5.18:
1. Freescale/NXP: fix populating children of Integrated Flash Controller
   DT nodes.

Issues existing before:
1. Renesas: fix platform-device leak in probe's error path.
2. Atmel: fix of_node reference leak in probe's error path.
3. Synopsys: correct the bindings for snps,ddrc-3.80a (interrupts are
   required).

* tag 'memory-controller-drv-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
  memory: fsl_ifc: populate child nodes of buses and mfd devices
  dt-bindings: memory: snps,ddrc-3.80a compatible also need interrupts
  memory: atmel-ebi: Fix missing of_node_put in atmel_ebi_probe
  memory: renesas-rpc-if: fix platform-device leak in error path

Link: https://lore.kernel.org/r/20220407081448.113208-1-krzysztof.kozlowski@linaro.orgSigned-off-by: NArnd Bergmann <arnd@arndb.de>

Merge tag 'samsung-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/fixes

Samsung fixes for v5.18

Update Krzysztof Kozlowski's email address in multiple maintainer
entries.  The old one @canonical.com bounces already.

* tag 'samsung-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
  MAINTAINERS: update Krzysztof Kozlowski's email to Linaro
  dt-bindings: update Krzysztof Kozlowski's email

Link: https://lore.kernel.org/r/20220407080545.112290-1-krzysztof.kozlowski@linaro.orgSigned-off-by: NArnd Bergmann <arnd@arndb.de>