Signed-off-by: NMichael Buesch <m@bues.ch>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Some members of the struct ssb_sprom where not filled with data available
in the NVRAM. Some attribute names in the NVRAM changed from SPROM version
3 to version 4. This patch was done by analyzing the the pci sprom parser
in the ssb code and some open source parts of the braodcom wireless driver
used on embedded devices.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2365/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We are generating the prefix based on the PCI bus address the device is
on. This is done like Broadcom does it in their code expect that the the
bus number is increased by one. In the SB bus implementation used by
Broadcom the SB bus emulates a PCI bus so the kernel sees one PCI bus
more then in our implementation. We do not handle prefixes like sb/1/
yet as they are only used on the new bus which is not implemented yet.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2364/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When an other SSB based device without an own SPROM is attached, using the
PCI bus to the main SSB based device, the data normally found in the SPROM
will be stored in the NVRAM on modern devices. The keys, to load the data
from the NVRAM, are all using some sort of prefix like pci/1/1/, pci/1/3/
or sb/1/ before the actual key. This patch extends bcm47xx_fill_sprom() to
make it possible to read out these values when some prefix was used.

The keys for the SPROM data used on the main chip does not have a prefix.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2363/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Some devices like the Netgear WGT634U are using ttyS1 for default console
output. We should switch to that console if it was given in the kernel_args
parameters.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1848/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Instead of writing own function for parsing the mac address we now
use sscanf.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1847/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fill the sprom with all available values from the nvram. Most of these
new values are needed for the b43 or b43legacy driver.

Parts of this patch have been in OpenWRT for a long time and were written
by Michael Buesch.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1846/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The config options read out here are not stored in CFE but only in NVRAM on
the devices. Remove reading from CFE and only access the NVRAM.  Reading out
CFE does not harm but is useless here.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1845/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Nvram_getenv should behave like cfe_getenv. cfe_getenv returns 0 on
success and -9 if the value was not found. If the input was wrong -8
will be returned by cfe_getenv.  Change nvram_getenv to do the same.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: Waldemar Brodkorb <wbx@openadk.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1520/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The previous patch 4a86f2d27733f610e642649aca3e82e86fca9e22 (lmo) rsp.
84a6fcb3 (kernel.org) was wrong.

The BCM47xx architecture maps the ram into a 128MB address space. It
will be spaced there as often as goes into the 128MB. Detection tries to
find the position where the same memory is found. When reading beyond
128MB the processor will throw an exception. If 128MB RAM is installed,
it will not find a memory alias because it tries to read beyond the 128MB
border. Now it just assumes 128MB installed ram if it can not find an
alias.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1508/Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When trying to netboot a Linksys WRT54GS WLAN router, the bootup fails,
because of following error message:

...
[    0.424000] b44: b44.c:v2.0
[    0.424000] b44: Invalid MAC address found in EEPROM
[    0.432000] b44 ssb0:1: Problem fetching invariants of chip,aborting
[    0.436000] b44: probe of ssb0:1 failed with error -22
...

The router uses a CFE bootloader, but most of the needed environment
variables for network card initialization, are not available from CFE
via printenv and even though not via cfe_getenv().
The required environment variables are saved in a special partition
in flash memory. The attached patch implement nvram_getenv and enables
bootup via NFS root on my router.

Most of the patch is extracted from the OpenWrt subversion repository and
stripped down and cleaned up to just fix this issue.

[Ralf: sorted out header file inclusions.  Lots of unneded headers and such
that should have been included.]
Signed-off-by: NWaldemar Brodkorb <wbx@openadk.org>
Reviewed-by: NPhil Sutter <phil@nwl.cc>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/1359/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Recent git versions now warn about those and they've always been a bit of
an annoyance.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Ignoring the last page when ddr size is 128M. Cached accesses to last page
is causing the processor to prefetch using address above 128M stepping out
of the DDR address space.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/981/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The MIPS-specific macro CL_SIZE is merely aliasing the macro
COMMAND_LINE_SIZE. Other architectures use the latter; also,
COMMAND_LINE_SIZE is documented in kernel-parameters.txt, so
let's use it, and remove the alias.
Signed-off-by: NDmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Since commit 22242681 ("MIPS: Extend
COMMAND_LINE_SIZE"), CL_SIZE is 4096 and local array variables with this
size will cause an build failure with default CONFIG_FRAME_WARN settings.

Although current users of such array variables are all early bootstrap
code and not likely to cause real stack overflow (thread_info corruption),
it is preferable to  to declare these arrays static with __initdata.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch adds support for the reset button of WGT634U machine, using
GPIO interrupts. Based on a patch from Michel Lespinasse.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch simplifies the BCM47xx GPIO code by using the new SSB GPIO
API, which does a lot things that were implemented directly in the
BCM47xx code.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds a printk message when a WGT634U machine is detected.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Switch the BCM47XX code to the new SPROM data structure now that the old
one has been removed.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Also many plat_timer_setup() can be killed too.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Hard to follow who is pointing what to where and why so it's simply getting
in the way of the time code renovation.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add LED support to the WGT634U machine.  It uses the new gpio-led
driver and a platform driver for the pin definitions.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add GPIO support to the BCM47XX platform.  It will be used by a GPIO
LED driver.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add CFE support to the BCM47XX code.  That includes querying CFE environment
variables as well as using CFE to print messages before the serial port is
initialized (early printk).
Signed-off-by: NAurelien Jarno <aurel32@farad.aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Note that the BCM4710 does not support the wait instruction, this
is not a mistake in the code.
    
It originally comes from the OpenWrt patches.
    
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Florian Schirmer <jolt@tuxbox.org>
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>