This change enables ECC correction for the packet buffer on all 82571
silicon.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

make mdio-gpio work with non OpenFirmware gpio implementation.

Aditional changes to mdio-gpio:
- use gpio_request() and gpio_free()
- place irq[] array in struct mdio_gpio_info
- add module description, author and license
- add note about compiling this driver as module
- rename mdc and mdio function (were ugly names)
- change MII to MDIO in bus name
- add __init __exit to module (un)loading functions
- probe fails if no phys added to the bus
- kzalloc bitbang with sizeof(*bitbang)

Changes since v3:
- keep bus naming "%x" to be compatible with existing drivers.

Changes since v2:
- more #ifdefs reduction
- platform driver will be registered on OF platforms also
- unified platform and OF bus_id to phy%i

Changes since v1:
- removed NO_IRQ
- reduced #idefs

Laurent, please test this driver under OF.
Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported by Stephen Rothwell:

drivers/net/dm9000.c:1450: error: expected ')' before ';' token
drivers/net/dm9000.c:1455: error: expected ';' before '}' token
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make pegasus driver not allocate a workqueue until the driver
is bound to some device, which will need that workqueue if
the device is brought up.  This conserves resources when the
driver is linked but there's no pegasus device connected.

Also shrink the runtime footprint a smidgeon by moving some
init-only code into its proper section, and move an obnoxious
(frequent and meaningless) message to be debug-only.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_carrier_off() is sufficient to stop Tx into the driver.  Stopping the Tx
queues is redundant and unnecessary.  By the same token, netif_carrier_on()
will be sufficient to re-enable Tx, so waking the queues is unnecessary.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
   netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.

This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
   netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.

This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
   netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.

This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We have some reasons to kill netdev->priv:
1. netdev->priv is equal to netdev_priv().
2. netdev_priv() wraps the calculation of netdev->priv's offset, obviously
   netdev_priv() is more flexible than netdev->priv.
But we cann't kill netdev->priv, because so many drivers reference to it
directly.

This patch is a safe convert for netdev->priv to netdev_priv(netdev).
Since all of the netdev->priv is only for read.
But it is too big to be sent in one mail.
I split it to 4 parts and make every part smaller than 100,000 bytes,
which is max size allowed by vger.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all related timeout constants to the same location.  BNX2
prefix is also added to make them more consistent.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default rx buffer water marks for XOFF/XON are for 1500 MTU.  At
larger MTUs, these water marks need to be adjusted for effective
flow control.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some quad-port cards that cannot support WoL on all ports due
to excessive power consumption, the driver needs to restrict WoL
on some ports by checking VAUX_PRESET bit.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NBenjamin Li <benli@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The latest vendor driver (rtl8187B_linux_26.1036.0708.2008) has a different
CCK power setting code as compared with the Linux driver.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NPiter Punk <piterpk@terra.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Keeping all the orinoco drivers in a common directory will make
maintenance easier.

Signed-off by: David Kilroy <kilroyd@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This introduces a debugfs file (ieee80211/phy#/hwsim/ps) that can be
used to force a simulated radio into power save mode. Following values
can be written into this file to change PS mode:
0 = power save disabled (constantly awake)
1 = power save enabled (drop all frames; do not send PS-Poll)
2 = power save enabled (send PS-Poll frames automatically to receive
    buffered unicast frames); not yet fully implemented
3 = manual PS-Poll trigger (send a single PS-Poll frame)

Two different behavior for power save mode processing can be tested:
- move between modes 1 and 0 (i.e., receive all buffered frames at a
  time)
- move to mode 1 and use manual PS-Poll frames (write 3 to the 'ps'
  debugfs file) to fetch power save buffered frames one at a time

Mode 2 (automatic PS-Poll) does not yet parse Beacon frames, but
eventually, it should take a look at TIM IE and send PS-Poll if a
traffic bit is set for our AID.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It was possible to trigger a kernel panic because beacon_timer may not
have been deleted in all cases when the kernel module was removed while
hostapd was still running.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Provide detailed information on TX queue parameter changes to make it
easier to debug mac80211 functionality.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Provide detailed information on BSS configuration changes to make it
easier to debug mac80211 functionality.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

skb->tail can't be meant here because it's not the same across 32/64 bit
compilations. This means there's no way the current driver can work on
64-bit architectures.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.27]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The new mechanism for allocing space for control frames,
didn't "zero" out the payload data... However I haven't
heard of any hiccups so far...
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fix rate scaling initialization. Rate scaling
was initialized always with B antenna.
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch change the name of the double inclusion protection in
iwl-commands.h
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch renames functions that are generic in iwl-agn and had a iwl4965
prefix.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 supports multiple virtual interfaces for a single device. For
example, a managed interface (wlan0) and a monitor interface (mon0) can
exist at the same time. Thus priv->iw_mode is not sufficient to track
the wireless mode any more. The patch redefines priv->iw_mode as the
first interface mode (the same as priv->vif->type if priv->vif != NULL).
If another monitor type interface is created later, we don't change
priv->iw_mode into monitor. This way, the original interface still
works. The patch also requests mac80211 to do reassociation after we
change the Rx filter flags.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes 4965 prefix from comments and one function
in iwl-agn-rs.h
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up FH bits and adds missing register values
that will be used later in TX initialization rewrite
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This implements proper short slot handling and adds code to
program the hardware for the correct response rates derived
from the basic rate set for the current BSS.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move calculation of CSR register offset into rt2x00debug.c
and remove the wrapper functions from each individual driver.
(Except rt2500usb, which still needs to wrap for the
different value type argument).
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

drivers/net/wireless/ath9k/xmit.c: In function ‘ath_tx_start’:
drivers/net/wireless/ath9k/xmit.c:1858: warning: ‘tid’ may be used uninitialized in this function
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The latest vendor driver (rtl8187B_linux_26.1036.0708.2008) has a 10 msec
delay after the call to set a new channel, but not before.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each of the primary write routines, rtl8187_write_phy(),
rtl8225_write_bitbang(), and rtl8225_write_8051() all conclude with an
msleep() command. Testing shows that these are not needed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Routine rtl8225_write() calls either rtl8225_write_bitbang() or
rtl8225_write_8051(), both of which end with an msleep() command. As a
result, a rtl8225_write() immediately followed by an msleep() is not needed.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>