This linksys dongle by default comes up in cdc_ether mode.
This patch allows r8152 to claim the device:
   Bus 002 Device 002: ID 13b1:0041 Linksys
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Reviewed-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace VLAN_HLEN and CRC_SIZE with ETH_FCS_LEN.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move calling delay_autosuspend() in rtl8152_runtime_suspend(). Calling
delay_autosuspend() as late as possible.

The original flows are
   1. check if the driver/device is busy now.
   2. set wake events.
   3. enter runtime suspend.

If the wake event occurs between (1) and (2), the device may miss it. Besides,
to avoid the runtime resume occurs after runtime suspend immediately, move the
checking to the end of rtl8152_runtime_suspend().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split rtl8152_resume() into rtl8152_runtime_resume() and
rtl8152_system_resume().

Besides, replace GFP_KERNEL with GFP_NOIO for usb_submit_urb().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add byte_enable for ocp_read_word() to replace reading 4
bytes data with reading the desired 2 bytes data.

This is used to avoid the issue which is described in
commit b4d99def ("r8152: remove sram_read"). The
original method always reads 4 bytes data, and it may
have problem when reading the PHY registers.

The new method is supported since RTL8153B, but it
doesn't influence the previous chips. The bits of the
byte_enable for the previous chips are the reserved
bits, and the hw would ignore them.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch supports two new chips for RTL8153B.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The settings of the new chip are the same with RTL8152, except that
its product ID is 0x8050.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Getting the device version out of the driver really aids debugging.
Signed-off-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change from using napi_complete to napi_complete_done to allow for the
use of gro_flush_timeout in tuning network processing.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stop queuing rx packets if it is more than 1000.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use PLA 0xe000 bit 8 to check if disabling ALDPS is finished.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move tp->rtl_ops.init() from rtl8152_resume() to rtl8152_reset_resume().
The initialization is only necessary for reset_resume().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only RTL8153 could set coalesce, so move the default setting for
rtl8152_probe() to r8153_init().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use another way to keep disabling the U2P3 for both RTL_VER_03 and
RTL_VER_04.

Move enabling U2P3 from r8153_init() to r8153_hw_phy_cfg(). The
engineer ask the setting should be done after PHY settings.

Disable U2P3 first in rtl8153_up().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust the order of rtl8153_runtime_enable() according to the
suggestion from the engineer.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the setting from r8153_first_init() to r8153_init(). It only needs to
be set once.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MAC clock speed down could be enabled if the U1/U2 is disabled.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable lpm after r8153_init() and remove other enable/disable lpm.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use r8153_phy_status() to check phy status of RTL8153.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make return value void since functions never returns meaningfull value.
Signed-off-by: NYuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function is not used, removing it fixes the following warning when
building with clang:

drivers/net/usb/r8152.c:825:5: error: unused function 'usb_ocp_read'
    [-Werror,-Wunused-function]
Signed-off-by: NMatthias Kaehlcke <mka@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without this the generic cdc_ether grabs the device,
and does not really work.
Signed-off-by: NRené Rebe <rene@exactcode.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The linking status may be changed when autosuspend. And, after
autoresume, the driver may try to transmit packets when the device
is carrier off, because the interrupt transfer doesn't update the
linking status, yet. And, if the device is in ALDPS mode, the device
would stop working.

The another similar case is
 1. unplug the cable.
 2. interrupt transfer queue a work_queue for linking change.
 3. device enters the ALDPS mode.
 4. a tx occurs before the work_queue is called.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

revert commit a59e6d81 ("r8152: correct the rx early size") and
fix the rx early size as

	(rx buffer size - rx packet size - rx desc size - alignment) / 4
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the received maximum size (RMS) according to the mtu size. It is
unnecessary to receive a packet which is more than the size we could
transmit. Besides, this could let the rx buffer be used effectively.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check hw version first in probe(). Do nothing if the driver doesn't
support the chip.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The list rx_done would be initialized when the linking on occurs.
Therefore, if a napi is scheduled without any linking on before,
the following kernel panic would happen.

	BUG: unable to handle kernel NULL pointer dereference at 000000000000008
	IP: [<ffffffffc085efde>] r8152_poll+0xe1e/0x1210 [r8152]
	PGD 0
	Oops: 0002 [#1] SMP
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace &tp->napi with napi and tp->netdev with netdev.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Acked-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Schedule the napi after napi_enable() for rx, if it is necessary.

If the rx is completed when napi is disabled, the sheduling of napi
would be lost. Then, no one handles the rx packet until next napi
is scheduled.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-schedule napi after napi_complete() for tx, if it is necessay.

In r8152_poll(), if the tx is completed after tx_bottom() and before
napi_complete(), the scheduling of napi would be lost. Then, no
one handles the next tx until the next napi_schedule() is called.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stop the tx when the napi is disabled to prevent napi_schedule() is
called.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adjust the setting of the flag of SELECTIVE_SUSPEND to prevent start_xmit()
from calling napi_schedule() directly during runtime suspend.

After calling napi_disable() or clearing the flag of WORK_ENABLE,
scheduling the napi is useless.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace rumtime with runtime.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Runtime suspend shouldn't be executed if the tx queue is not empty,
because the device is not idle.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rtl8152_post_reset() should sumbit rx urb and interrupt transfer,
otherwise the rx wouldn't work and the linking change couldn't be
detected.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the hw rx checksum is always enabled, and the user couldn't switch
it to sw rx checksum.

Note that the RTL_VER_01 only support sw rx checksum only. Besides,
the hw rx checksum for RTL_VER_02 is disabled after
commit b9a321b4 ("r8152: Fix broken RX checksums."). Re-enable it.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pause the rx and make sure the rx fifo is empty when the autosuspend
occurs.

If the rx data comes when the driver is canceling the rx urb, the host
controller would stop getting the data from the device and continue
it after next rx urb is submitted. That is, one continuing data is
split into two different urb buffers. That let the driver take the
data as a rx descriptor, and unexpected behavior happens.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split rtl8152_suspend() into rtl8152_system_suspend() and
rtl8152_rumtime_suspend().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>