The ACK/NACK implementation as found in e.g. the G965 has the falling
clock edge and the release of the data line after the ACK for the received
byte happen at the same time.

This is conformant with the I2C specification, which allows a zero hold
time, see footnote [3]: "A device must internally provide a hold time of
at least 300 ns for the SDA signal (with respect to the V IH(min) of the
SCL signal) to bridge the undefined region of the falling edge of SCL."

Some HDMI-to-VGA converters apparently fail to adhere to this requirement
and latch SDA at the falling clock edge, so instead of an ACK
sometimes a NACK is read and the slave (i.e. the EDID ROM) ends the
transfer.

The bitbanging releases the data line for the ACK only 1/4 bit time after
the falling clock edge, so a slave will see the correct value no matter
if it samples at the rising or the falling clock edge or in the center.

Fallback to bitbanging is already done for the CRT connector.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92685Signed-off-by: NStefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/a39f080b-81a5-4c93-b3f7-7cb0a58daca3@rwthex-w2-a.rwth-ad.de
(cherry picked from commit cfb926e1)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Since the firmwares are not yet released to public repo,
disable them on Geminilake.

v2: Remove the firmware versions (Michal)

v3: Remove unwanted defines (Rodrigo)
Correct commit message (Michal)

Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Fixes: 90f192c8 ("drm/i915/GuC/GLK: Load GuC on GLK")
Fixes: db5ba0d8 ("drm/i915/GLK/HuC: Load HuC on GLK")
Reviewed-by: NMichal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1515006225-13003-1-git-send-email-anusha.srivatsa@intel.com
(cherry picked from commit a76050a4)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

The mocs reg array is defined locally but then we iterate over its
elements using I915_NUM_ENGINES. There is no 'hard' connection between
I915_NUM_ENGINES and the regs array and there will be problems if either
of them increases.

Use the size of the mocs reg array instead to safely iterate over it.
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Cc: Weinan Li <weinan.z.li@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

GVT may receive partial write on one guest PTE update. Validate gfn
not to translate incomplete gfn. This avoids some unnecessary error
messages incurred by the incomplete gfn translating. Also fix the
bug that the whole PPGTT shadow page update is aborted on any invalid
gfn entry.

gfn validation relys on hypervisor's help. Add one MPT module function
to provide the function.
Signed-off-by: NHang Yuan <hang.yuan@intel.com>
Reviewed-by: NZhi Wang <zhi.a.wang@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Running 4.15 Linux kernel in VM will cause host GVT reports
'untrack mmio 0x701a0' errror, which identifies the PLANE_KEYMAX
registers. Add them to track list.

v2: rebase to latest staging code.
Signed-off-by: NPei Zhang <pei.zhang@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

while(mmio++) increase mmio to next, mmio[0] never take effect
in while loop.

This patch change while to for and fix the above issue.

v2: Correct Fixes format.(Zhenyu)
v3: Rebase to latest staging.(Zhenyu)

Fixes: 83164886("drm/i915/gvt: Select appropriate mmio list at initialization time")
Signed-off-by: NXiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

In the past the ast driver relied upon the fbdev emulation helpers to
call ->load_lut at boot-up. But since

commit b8e2b019
Author: Peter Rosin <peda@axentia.se>
Date:   Tue Jul 4 12:36:57 2017 +0200

    drm/fb-helper: factor out pseudo-palette

that's cleaned up and drivers are expected to boot into a consistent
lut state. This patch fixes that.

Fixes: b8e2b019 ("drm/fb-helper: factor out pseudo-palette")
Cc: Peter Rosin <peda@axenita.se>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: <stable@vger.kernel.org> # v4.14+
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=198123
Cc: Bill Fraser <bill.fraser@gmail.com>
Reported-and-Tested-by: NBill Fraser <bill.fraser@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Merge tag 'drm-misc-next-fixes-2018-01-31' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

This contains a fix to restrict what lessee can do with masters and
another one when waiting for timeouts on reservation objects.

* tag 'drm-misc-next-fixes-2018-01-31' of git://anongit.freedesktop.org/drm/drm-misc:
  drm: Check for lessee in DROP_MASTER ioctl
  dma-buf: fix reservation_object_wait_timeout_rcu once more v2

Don't let a lessee control what the current DRM master is set to;
that's the job of the "real" master. Otherwise, the lessee would
disable all access to master operations for the owner and all lessees
under it.

This matches the same check made in the SET_MASTER ioctl.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Fixes: 2ed077e4 ("drm: Add drm_object lease infrastructure [v5]")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180119015159.1606-1-keithp@keithp.com

Merge tag 'drm-misc-next-fixes-2018-01-18' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

Fixes for 4.16:

Fixes one Kconfig issue and a enable some panels to work properly.
There is also a fix of error code return in sun4i.

* tag 'drm-misc-next-fixes-2018-01-18' of git://anongit.freedesktop.org/drm/drm-misc:
  drm: Fix PANEL_ORIENTATION_QUIRKS breaking the Kconfig DRM menuconfig
  drm/panel: lvds: Handle the optional regulator case properly
  drm/sun4i: Fix error code in sun4i_tcon_bind()

 A few more fixes for 4.16, nothing major.

A few more fixes for 4.16.  This is on top of the pull request from
last week.  Most notable change here is a fix to the link order for
the now separate from amdgpu GPU scheduler to fix crashes when the
modules are build into the kernel rather than as modules.

* 'drm-next-4.16' of git://people.freedesktop.org/~agd5f/linux:
  drm: fix gpu scheduler link order
  drm/amd/display: Demote error print to debug print when ATOM impl missing
  drm/amdgpu: Avoid leaking PM domain on driver unbind (v2)
  drm/amd/amdgpu: Add Polaris version check
  drm/amdgpu: Reenable manual GPU reset from sysfs
  drm/amdgpu: disable MMHUB power gating on raven
  drm/ttm: Don't unreserve swapped BOs that were previously reserved
  drm/ttm: Don't add swapped BOs to swap-LRU list
  drm/amdgpu: only check for ECC on Vega10
  drm/amd/powerplay: Fix smu_table_entry.handle type
  drm/ttm: add VADDR_FLAG_UPDATED_COUNT to correctly update dma_page global count
  drm/radeon: fill in rb backend map on evergreen/ni.
  drm/amdgpu/gfx9: fix ngg enablement to clear gds reserved memory (v2)
  drm/ttm: only free pages rather than update global memory count together
  drm/amdgpu: fix CPU based VM updates
  drm/amdgpu: fix typo in amdgpu_vce_validate_bo
  drm/amdgpu: fix amdgpu_vm_pasid_fault_credit
  drm/ttm: check the return value of register_shrinker
  drm/radeon: fix sparse warning: Should it be static?

It should initialize before the drivers using it.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=104736Reviewed-by: NMike Lothian <mike@fireburn.co.uk>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

I assumed wrongfully that all relevant functions should be implemented.
Apparently this isn't the case. Demote the print to debug level for now.
Signed-off-by: NHarry Wentland <harry.wentland@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NHarry Wentland <harry.wentland@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We need to set shared_count even if we already have a fence to wait for.

v2: init i to -1 as well
Signed-off-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Tested-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NLyude Paul <lyude@redhat.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180122200003.6665-1-christian.koenig@amd.com

We only support vga_switcheroo and runtime pm on PX/HG systems
so forcing runpm to 1 doesn't do anything useful anyway.

Only call vga_switcheroo_init_domain_pm_ops() for PX/HG so
that the cleanup path is correct as well.  This mirrors what
radeon does as well.

v2: rework the patch originally sent by Lukas (Alex)
Acked-by: NLukas Wunner <lukas@wunner.de>
Reported-by: NLukas Wunner <lukas@wunner.de>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de> (v1)
Cc: stable@vger.kernel.org

Add Polaris version check if firmware support UVD encode
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Otherwise it keeps rejecting the reset.
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

MMHUB power gating still has issue, and doesn't work on raven at current. So
disable it for the moment.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Acked-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

If ttm_bo_swapout doesn't own the lock, don't release it. Someone
else probably depends on it still being locked.
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

A BO that's already swapped would be added back to the swap-LRU list
for example if its validation failed under high memory pressure. This
could later lead to swapping it out again and leaking previous swap
storage.

This commit adds a condition to prevent that from happening.

v2: Check page_flags instead of swap_storage
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

RV doesn't support it.
Reviewed-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The handle describes kernel logical address, should be
unsigned long and not uint32_t.
Fixes KASAN error and GFP on driver unload.
Reviewed-by: NRex Zhu <Rex.Zhu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

add this for correctly updating global mem count in ttm_mem_zone.
before that when ttm_mem_global_alloc_page fails, we would update all
dma_page's global mem count in ttm_dma->pages_list. but actually here
we should not update for the last dma_page.

v2: only the update of last dma_page is not right
v3: use lower bits of dma_page vaddr
Signed-off-by: NRoger He <Hongbo.He@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Merge tag 'drm-amdkfd-next-fixes-2018-01-15' of git://people.freedesktop.org/~gabbayo/linux into drm-next

- fix NULL pointer dereference
- fix compiler warning on large define values
- remove unnecessary call to execute_queues_cpsch

* tag 'drm-amdkfd-next-fixes-2018-01-15' of git://people.freedesktop.org/~gabbayo/linux:
  drm/amdkfd: Fix potential NULL pointer dereferences
  drm/amdkfd: add ull suffix to 64bit defines
  drm/amdkfd: don't always call execute_queues_cpsch()
  drm/amdkfd: Fix return value 0 when execute_queues_cpsch fails

Linux 4.15-rc8

Daniel requested this for so the intel CI won't fall over on drm-next
so often.

All Kconfig menu menu entries should have a depends on MENU_OPTION, the
menu stops after the first Kconfig entry without this depends on.

Since the PANEL_ORIENTATION_QUIRKS option is also used outside of DRM,
it deliberately does not have a depends on DRM, but this causes all
items after it to show as separate items rather then under the DRM
menuconfig.

This commit moves PANEL_ORIENTATION_QUIRKS to the end of the drm Kconfig
file, grouping it with DRM_LIB_RANDOM which also does not depend on DRM,
fixing the DRM menuconfig.

Fixes: 404d1a3e ("drm: Add panel orientation quirks, v6.")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180117081032.6411-1-hdegoede@redhat.com

This looks to have never gotten filled in, and it seems to
 trigger a bug in mesa.
Reviewed-by: NRoland Scheidegger <sroland@vmware.com>
Reported-by: NRoland Scheidegger <sroland@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

v2: fix register access
Signed-off-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Reviewed-by: NKen Wang <ken.wang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

if ttm_get_pages or ttm_mem_global_alloc_page fail, should not update
global memory count.
Signed-off-by: NRoger He <Hongbo.He@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Tested-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

That got accidentially removed.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Otherwise buffer placement is very restrictive and might fail.

Fixes: "drm/amdgpu: fix VCE buffer placement restrictions v2"
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reported-by: NDeng, Emily <Emily.Deng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

As soon as the lock is dropped the VM pointer can be invalid.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NChunming Zhou <david1.zhou@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This fixes the build warning:
"ignoring return value of 'register_shrinker', declared with
attribute warn_unused_result [-Wunused-result]"
Signed-off-by: NRoger He <Hongbo.He@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Impact: make symbol static.

Fix this sparse warning:
  drivers/gpu/drm/radeon/radeon_dp_mst.c:332:38: warning: symbol 'mst_cbs' was not declared. Should it be static?
Signed-off-by: NDmitry Rozhkov <dmitry.rozhkov@linux.intel.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The devm_regulator_get_optional function, unlike it was assumed in the
commit a1c55bcc ("drm/panel: lvds: Add support for the power-supply
property"), is actually returning an error pointer with -ENODEV instead of
NULL when there's no regulator to find.

Make sure we handle that case properly.
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Fixes: a1c55bcc ("drm/panel: lvds: Add support for the power-supply property")
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110155941.16109-1-maxime.ripard@free-electrons.com

We accidentally passed the wrong variable to PTR_ERR().

Fixes: a0c1214e ("drm/sun4i: Add LVDS support")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180115081113.wlam5wkmdynisf4r@mwanda

Pull x86 fixlet from Thomas Gleixner.

Remove a warning about lack of compiler support for retpoline that most
people can't do anything about, so it just annoys them needlessly.

* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/retpoline: Remove compile time warning

Pull powerpc fixes from Michael Ellerman:
 "One fix for an oops at boot if we take a hotplug interrupt before we
  are ready to handle it.

  The bulk is patches to implement mitigation for Meltdown, see the
  change logs for more details.

  Thanks to: Nicholas Piggin, Michael Neuling, Oliver O'Halloran, Jon
  Masters, Jose Ricardo Ziviani, David Gibson"

* tag 'powerpc-4.15-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/powernv: Check device-tree for RFI flush settings
  powerpc/pseries: Query hypervisor for RFI flush settings
  powerpc/64s: Support disabling RFI flush with no_rfi_flush and nopti
  powerpc/64s: Add support for RFI flush of L1-D cache
  powerpc/64s: Convert slb_miss_common to use RFI_TO_USER/KERNEL
  powerpc/64: Convert fast_exception_return to use RFI_TO_USER/KERNEL
  powerpc/64: Convert the syscall exit path to use RFI_TO_USER/KERNEL
  powerpc/64s: Simple RFI macro conversions
  powerpc/64: Add macros for annotating the destination of rfid/hrfid
  powerpc/pseries: Add H_GET_CPU_CHARACTERISTICS flags & wrapper
  powerpc/pseries: Make RAS IRQ explicitly dependent on DLPAR WQ

Remove the compile time warning when CONFIG_RETPOLINE=y and the compiler
does not have retpoline support. Linus rationale for this is:

  It's wrong because it will just make people turn off RETPOLINE, and the
  asm updates - and return stack clearing - that are independent of the
  compiler are likely the most important parts because they are likely the
  ones easiest to target.

  And it's annoying because most people won't be able to do anything about
  it. The number of people building their own compiler? Very small. So if
  their distro hasn't got a compiler yet (and pretty much nobody does), the
  warning is just annoying crap.

  It is already properly reported as part of the sysfs interface. The
  compile-time warning only encourages bad things.

Fixes: 76b04384 ("x86/retpoline: Add initial retpoline support")
Requested-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: gnomes@lxorguk.ukuu.org.uk
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: thomas.lendacky@amd.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kees Cook <keescook@google.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linux-foundation.org>
Link: https://lkml.kernel.org/r/CA+55aFzWgquv4i6Mab6bASqYXg3ErV3XDFEYf=GEcCDQg5uAtw@mail.gmail.com