o Defer napi resouce allocation to device attach.

o Free napi resources and delete napi during detach.

This ensures right behavior across firmware reset.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Remove private workqueue in the driver, move all
  scheduled tasks to keventd workqueues. This makes
  ports (interfaces) of same / different NIC boards
  independent, in terms of their link watchdog and
  reset tasks.

o Move quick checks for link status and temperature
  in timer callback, schedule watchdog task only if
  link status changed or temperature reached critical
  threshold.

This also fixes deadlock when thermal panic occurs,
watchdog work was flushing workqueue that it was
sitting on.
Signed-off-by: NAmit Kumar Salecha <amit@qlogic.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the calculation of remaining header length in TSO
over vlan device case. This was inadvertently missed
out in patch 028afe71 ("netxen: add vlan
tx acceleration support").
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix dma mask calculation that caps at 63-bit addressing even
when firmware advertises full 64-bit support.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change default dma mask for NX3031 to 39 bit with ability
to update it to 64-bit (if firmware indicates support). Old
code was restricting it under 4GB (32-bit), sometimes causing
failure to allocate descriptor rings on heavily populated
system. NX2031 based NICs will still get 32-bit coherent mask.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Wrap dest IP hashing code with #ifdef CONFIG_INET,
this feature makes no sense without INET, but other
driver can still work.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for ethtool -G to tune rx and tx ring sizes
per interface basis.

This is only supported for NX3031 based cards.
Signed-off-by: NAmit Kumar Salecha <amit@netxen.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable vlan tx acceleration for NX3031 if firmware advertises
capability.
Signed-off-by: NAmit Kumar Salecha <amit@netxen.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move all net_device initialization into one function
netxen_setup_netdev().
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NX2031 firmware version will never be > 4.0.0, so replace
(adapter->fw_major < 4) checks with pci revision ID check.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o move all tso / checksum offload code into netxen_tso_check().
o optimize the tso header copy into simple loop.
o clean up unnecessary unions from cmd_desc_type0 struct.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o remove superfluous code to setup PCI dma watchdog for NX2031.
o disable dma watchdog completely for NX3031 (not required).
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Initialize and configure interrupt coalesing defaults
in the firmware, so that these also reflect in "ethool -c".
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NX3031 hardware requires local IP addresses for packet
accumulation (LRO). IP address hashing is required to
distinguish a local TCP flow from others (forwarded or
guest).

This patch adds listener for IP and netdev events and
configures IP address in the firmware.
Signed-off-by: NAmit Kumar Salecha <amit@netxen.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o move dma mask update to netxen_start_firmware() so that
  if firmware changes across suspend (e.g. file -> flash)
  it reflects right dma mask.
o re-read firmware capabilities after firmware reset.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check temperature for all PCI functions, that can allow
graceful shutdown of all interfaces on the overheated card.

Old code was only monitoring temperature for function 0 only.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netxen: fix deadlock on dev close

The tx ring accounting fix in commit cb2107be
("netxen: fix tx ring accounting") introduced intermittent
deadlock when inteface is going down.

This was possibly combined effect of speculative tx pause,
calling netif_tx_lock instead of queue lock and unclean
synchronization with napi which could end up unmasking
interrupt.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Use D3 reset context deletion for NX2031, it cleans up
  more resources in the firmware.
o Release rx buffers after hardware context has been reset.
o Delete tx context after rx context, some firmware control
  commands are sent on tx context, so it should be the last
  to go.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Restrict firmware reset to following cases -

o chip rev is NX2031 (firmare doesn't support heartbit).
o firmware is dead.
o previous attempt to init firmware had failed.
o we have got newer file firmware.

This speeds up module load tremendously (by upto 8 sec),
also avoids downtime for NCSI (management) pass-thru
traffic.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure all functions run firmware init handshake.

If PCI function 0 fails to initialize firmware, mark the
state failed so that other functions on the same board
bail out quickly instead of waiting 30s for firmware
handshake.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

wrap pci suspend() and resume() with CONFIG_PM check.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This forces every update of tx ring producer to check for
availability of space for next full TSO command. Earlier
firmware control commands didn't care to pause tx queue.

Stop the tx queue if there's not enough space to transmit one full
LSO command left on the tx ring after current transmit. This avoids
returning NETDEV_TX_BUSY after checking distance between producer
and consumer on every cpu.

Restart the tx queue only if we have cleaned up enough tx
descriptors.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Followup of commits 9d21493b
and 08baf561
(net: tx scalability works : trans_start)
(net: txq_trans_update() helper)

Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Multi queue drivers can
avoid one cache miss (on dev->trans_start) in their start_xmit()
handler.

Exceptions are NETIF_F_LLTX drivers (vxge & tehuti)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pdev->irq was not saved in netxen_adapter, causing request_irq()
with invalid irq number.

This was broken in commit be339aee
("netxen: fix irq tear down and msix leak.").
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This board doesn't suppot msi-x well due to msi-x table
mapping (hardware) issue.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Fix the order of irq and hardware context teardown.
  Also synchronize the interrupt in dev close() before
  releasing tx buffers.

o Fix possible msi-x vector leak if available vectors are
  less than requested.

o Request multiple msix vectors only if hardware supports
  multiple rx queues.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store msi target status register offset in adapter struct.
This avoids contention on msi_tgt_status table from interrupt
hadlers of different pci function.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Pause traffic during mac addr change.
o Enable setting mac address for NX3031.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o use standard linked list api for mac addr list management
  in NX3031.
o release mac addresses in firmware in dev close().
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the distance check between tx ring producer and consumer that
could lead to tx ring wrap around.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o hold the firmware in memory across suspend, since filesystem
  may not be up after resuming.
o reset the chip after requesting firmware, to minimize downtime
  for NC-SI.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o move related fields into netxen_recv_context struct.
o allocate rx buffer and descriptor rings dynamically.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Firmware starting 4.0.402 started supporting link events, disable
it for older firmwares.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAmit Kumar Salecha <amit@netxen.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable multiple rx rings for older NX2031 chip, firmware 3.4.336
or newer supports this feature.
Signed-off-by: NAmit Kumar Salecha <amit@netxen.com>
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace superfluous wrapper functions with two macros:

NXWR32 replaces netxen_nic_reg_write, netxen_nic_write_w0,
netxen_nic_read_w1, netxen_crb_writelit_adapter.

NXRD32 replaces netxen_nic_reg_read, netxen_nic_read_w0,
netxen_nic_read_w1.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o remove unnecessary length parameter since register access
  width is fixed 4 byte.
o remove superfluous pci_read_normalize and pci_write_normalize
  functions.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reduces netxen_adapter footprint when rss (msi-x) is disabled.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for asynchronous events from firmware,
received over one of the rx rings.

Add support for event based phy interrupts, enhanced links
status reporting from firmware.
Signed-off-by: NDhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>