Since a TCE page size can be other than 4K, make it configurable for
P5IOC2 and IODA PHBs.
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The current implementation of IOMMU on sPAPR does not use iommu_ops
and therefore does not call IOMMU API's bus_set_iommu() which
1) sets iommu_ops for a bus
2) registers a bus notifier
Instead, PCI devices are added to IOMMU groups from
subsys_initcall_sync(tce_iommu_init) which does basically the same
thing without using iommu_ops callbacks.

However Freescale PAMU driver (https://lkml.org/lkml/2013/7/1/158)
implements iommu_ops and when tce_iommu_init is called, every PCI device
is already added to some group so there is a conflict.

This patch does 2 things:
1. removes the loop in which PCI devices were added to groups and
adds explicit iommu_add_device() calls to add devices as soon as they get
the iommu_table pointer assigned to them.
2. moves a bus notifier to powernv code in order to avoid conflict with
the notifier from Freescale driver.

iommu_add_device() and iommu_del_device() are public now.
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The patch initializes EEH for PowerNV platform. Because the OPAL
APIs requires HUB ID, we need trace that through struct pnv_phb.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This initializes IOMMU groups based on the IOMMU configuration
discovered during the PCI scan on POWERNV (POWER non virtualized)
platform.  The IOMMU groups are to be used later by the VFIO driver,
which is used for PCI pass through.

It also implements an API for mapping/unmapping pages for
guest PCI drivers and providing DMA window properties.
This API is going to be used later by QEMU-VFIO to handle
h_put_tce hypercalls from the KVM guest.

The iommu_put_tce_user_mode() does only a single page mapping
as an API for adding many mappings at once is going to be
added later.

Although this driver has been tested only on the POWERNV
platform, it should work on any platform which supports
TCE tables.  As h_put_tce hypercall is received by the host
kernel and processed by the QEMU (what involves calling
the host kernel again), performance is not the best -
circa 220MB/s on 10Gb ethernet network.

To enable VFIO on POWER, enable SPAPR_TCE_IOMMU config
option and configure VFIO as required.

Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The EOI handler of MSI/MSI-X interrupts for P8 (PHB3) need additional
steps to handle the P/Q bits in IVE before EOIing the corresponding
interrupt. The patch changes the EOI handler to cover that. we have
individual IRQ chip in each PHB instance. During the MSI IRQ setup
time, the IRQ chip is copied over from the original one for that IRQ,
and the EOI handler is patched with the one that will handle the P/Q
bits (As Ben suggested).
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

As Michael Ellerman mentioned, arch/powerpc/sysdev/msi_bitmap.c
already implemented bitmap to manage (alloc/free) MSI interrupts.
The patch intends to use that mechanism to manage MSI interrupts
for PowerNV platform.
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>

CONFIG_HOTPLUG is going away as an option.  As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

It's empty now, apart from other includes.

Fixup a few files that were getting things via this header.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This implements support for MSIs on p5ioc2 PHBs. We only support
MSIs on the PCIe PHBs, not the PCI-X ones as the later hasn't been
properly verified in HW.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This adds support for PCI-X and PCIe on the p5ioc2 IO hub using
OPAL. This includes allocating & setting up TCE tables and config
space access routines.

This also supports fallbacks via RTAS when OPAL is absent, using
legacy TCE format pre-allocated via the device-tree (BML style)
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>