Added device ID for NVMe Switch Adapter (Ambrosia).
VID: 0x1000
DID: 0x02B1
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

MPI Endpoint is a PCIe switch based on MPI2.

Renaming device ID macro from MPI2_MFGPAGE_DEVID_SAS2308_MPI_EP to
MPI2_MFGPAGE_DEVID_SWITCH_MPI_EP.
Signed-off-by: NSuganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.

Addresses-Coverity-ID: 1475400 ("Missing break in switch")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

With commit 09c2f95a ("scsi: mpt3sas: Swap I/O memory read value back
to cpu endianness"), 64bit writes in _base_writeq() were rewritten to use
__raw_writeq() instad of writeq().

This introduced a bug apparent on powerpc64 systems such as the Raptor
Talos II that causes the HBA to drop from the PCIe bus under heavy load and
being reinitialized after a couple of seconds.

It can easily be triggered on affacted systems by using something like

  fio --name=random-write --iodepth=4 --rw=randwrite --bs=4k --direct=0 \
    --size=128M --numjobs=64 --end_fsync=1
  fio --name=random-write --iodepth=4 --rw=randwrite --bs=64k --direct=0 \
    --size=128M --numjobs=64 --end_fsync=1

a couple of times. In my case I tested it on both a ZFS raidz2 and a btrfs
raid6 using LSI 9300-8i and 9400-8i controllers.

The fix consists in resembling the write ordering of writeq() by adding a
mandatory write memory barrier before device access and a compiler barrier
afterwards. The additional MMIO barrier is superfluous.
Signed-off-by: NStephan Günther <moepi@moepi.net>
Reported-by: NMatt Corallo <linux@bluematt.me>
Acked-by: NSreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page.  Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update driver version from 27.100.00.00 to 27.101.00.00.
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use ioc->base_readl to restrict the readl retries to only Aero controllers.
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Sometimes Aero controllers appears to be returning bad data (0) for
doorbell register read and if retries are performed immediately after the
bad read, they return good data.

Workaround is added to retry read from doorbell registers for maximum three
times if driver get the zero.  Added functions base_readl_aero for Aero IOC
and base_readl for gen35 and other controllers.
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Adding flag "is_aero_ioc" to differentiate aero based controllers from
other gen35 controllers.
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

There is a spelling mistake in some description text, fix it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Display following warning message only upon detection of configurable
secure type controllers.

"HBA is in Configurable Secure mode"

[mkp: typos]
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Modify driver version to 27.100.00.00 (which is equivalent to PH8 OOB
driver)
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently driver is modifying both current & NVRAM/persistent data in
Manufacturing page11. Driver should change only current copy of
Manufacturing page11. It should not modify the persistent data.

So removed the section of code where driver is modifying the persistent
data of Manufacturing page11.
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If EEDPTagMode field in manufacturing page11 is set then unset it. This is
needed to fix a hardware bug only in SAS3/SAS2 cards. So, skipping
EEDPTagMode changes in Manufacturing page11 for SAS 3.5 controllers.
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This is to fix SYNC CACHE and START STOP command failures with
DID_NO_CONNECT during driver unload.

In driver's IO submission patch (i.e. in driver's .queuecommand()) driver
won't allow any SCSI commands to the IOC when ioc->remove_host flag is set
and hence SYNC CACHE commands which are issued to the target drives (where
write cache is enabled) during driver unload time is failed with
DID_NO_CONNECT status.

Now modified the driver to allow SYNC CACHE and START STOP commands to IOC,
even when remove_host flag is set.
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Call sas_remove_host() before removing the target devices in the driver's
.remove() callback function(i.e. during driver unload time).  So that
driver can provide a way to allow SYNC CACHE, START STOP unit commands
etc. (which are issued from SML) to the target drives during driver unload
time.

Once sas_remove_host() is called before removing the target drives then
driver can just clean up the resources allocated for target devices and no
need to call sas_port_delete_phy(), sas_port_delete() API's as these API's
internally called from sas_remove_host().
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No functional change. Doing code refactor of function
mpt3sas_wait_for_ioc() for better readability.
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No functional changes. This section of code "wait for IOC to be
operational" is used in many places across the driver.  Factor this code
out into a new mpt3sas_wait_for_ioc().
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Added new #define variable IOC_OPERATIONAL_WAIT_COUNT and it replaces hard
coded value '10' in all the places where driver is waiting for the IOC to
become operational.
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Reviewed-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add support for Aero/Sea controllers and add warning for configurable
secure type IOC.
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Updating MPI headers to the latest version 2.6.7 to add support to the
driver to detect the new 3816 and 3916 chip based controllers.  Separate
out firmware image data from mpi2_ioc.h to new file mpi2_image.h
Signed-off-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Switch from the legacy PCI DMA API to the generic DMA API.

Also simplify setting the DMA mask a bit.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Clang warns when multiple pairs of parentheses are used for a single
conditional statement.

drivers/scsi/mpt3sas/mpt3sas_base.c:535:11: warning: equality comparison
with extraneous parentheses [-Wparentheses-equality]
        if ((ioc == NULL))
             ~~~~^~~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:535:11: note: remove extraneous
parentheses around the comparison to silence this warning
        if ((ioc == NULL))
            ~    ^      ~
drivers/scsi/mpt3sas/mpt3sas_base.c:535:11: note: use '=' to turn this
equality comparison into an assignment
        if ((ioc == NULL))
                 ^~
                 =
drivers/scsi/mpt3sas/mpt3sas_base.c:539:12: warning: equality comparison
with extraneous parentheses [-Wparentheses-equality]
        if ((pdev == NULL))
             ~~~~~^~~~~~~
drivers/scsi/mpt3sas/mpt3sas_base.c:539:12: note: remove extraneous
parentheses around the comparison to silence this warning
        if ((pdev == NULL))
            ~     ^      ~
drivers/scsi/mpt3sas/mpt3sas_base.c:539:12: note: use '=' to turn this
equality comparison into an assignment
        if ((pdev == NULL))
                  ^~
                  =
2 warnings generated.

Remove them and while we're at it, simplify the NULL checks as '!var' is
used more than 'var == NULL'.
Signed-off-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replaced dma_pool_alloc + memset with dma_pool_zalloc.
Signed-off-by: NBrajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: NSouptick Joarder <jrdr.linux@gmail.com>
Acked-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

All the uses have been removed, delete the macro.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Convert these uses to ioc_<level> where appropriate.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Remove the logging level as panic calls stop the machine and should always be
emitted regardless of requested logging level.

These existing panic uses are perhaps inappropriate.

Miscellanea:

o Coalesce formats and convert MPT3SAS_FMT to "%s: " to improve clarity
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Convert the existing 2 uses to make the format and arguments matching more
obvious.

Miscellanea:

o Move the word "enabled" into the format to trivially reduce object size
o Remove unnecessary parentheses
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

These have misordered uses of __func__ and ioc->name that could mismatch
MPT3SAS_FMT and "%s: ".

Convert them to ioc_<level>.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use a more common logging style.

Done using the perl script below and some typing

$ git grep --name-only -w MPT3SAS_FMT -- "*.c" | \
  xargs perl -i -e 'local $/; while (<>) { s/\bpr_(info|err|notice|warn)\s*\(\s*MPT3SAS_FMT\s*("[^"]+"(?:\s*\\?\s*"[^"]+"\s*){0,5}\s*),\s*ioc->name\s*/ioc_\1(ioc, \2/g; print;}'

Miscellanea for these conversions:

o Coalesce formats
o Realign arguments
o Remove unnecessary parentheses
o Use casts to u64 instead of unsigned long long where appropriate
o Convert broken pr_info uses to pr_cont
o Fix broken format string concatenation with line continuations and
  excess whitespace
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

These macros can help identify specific logging uses and eventually perhaps
reduce object sizes.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NSuganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

After bfcb79fc ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.

Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: NOza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

Below kernel BUG was observed while running IOs with host reset (issued
from application),

mpt3sas_cm0: diag reset: SUCCESS
------------[ cut here ]------------
WARNING: CPU: 12 PID: 4336 at drivers/scsi/mpt3sas/mpt3sas_base.c:3282 mpt3sas_base_clear_st+0x3d/0x40 [mpt3sas]
Modules linked in: macsec tcp_diag udp_diag inet_diag unix_diag af_packet_diag netlink_diag binfmt_misc fuse xt_CHECKSUM ipt_MASQUERADE nf_nat_masquerade_ipv4 tun devlink ip6t_rpfilter ipt_REJECT nf_reject_ipv4 ip6t_REJECT nf_reject_ipv6 xt_conntrack ip_set nfnetlink ebtable_nat ebtable_broute bridge stp llc ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter sunrpc vfat fat sb_edac intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd iTCO_wdt iTCO_vendor_support
 dcdbas pcspkr joydev ipmi_ssif ses enclosure sg ipmi_devintf acpi_pad ipmi_msghandler acpi_power_meter mei_me lpc_ich wmi mei shpchp ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic ata_generic pata_acpi uas usb_storage mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm ata_piix mpt3sas libata crct10dif_pclmul crct10dif_common tg3 crc32c_intel i2c_core raid_class ptp scsi_transport_sas pps_core dm_mirror dm_region_hash dm_log dm_mod
CPU: 12 PID: 4336 Comm: python Kdump: loaded Tainted: G        W      ------------   3.10.0-875.el7.brdc.x86_64 #1
Hardware name: Dell Inc. PowerEdge R820/0YWR73, BIOS 1.5.0 03/08/2013
Call Trace:
 [<ffffffff9cf16583>] dump_stack+0x19/0x1b
 [<ffffffff9c891698>] __warn+0xd8/0x100
 [<ffffffff9c8917dd>] warn_slowpath_null+0x1d/0x20
 [<ffffffffc04f3f4d>] mpt3sas_base_clear_st+0x3d/0x40 [mpt3sas]
 [<ffffffffc05047d2>] _scsih_flush_running_cmds+0x92/0xe0 [mpt3sas]
 [<ffffffffc05095db>] mpt3sas_scsih_reset_handler+0x43b/0xaf0 [mpt3sas]
 [<ffffffff9c894829>] ? vprintk_default+0x29/0x40
 [<ffffffff9cf10531>] ? printk+0x60/0x77
 [<ffffffffc04f06c8>] ? _base_diag_reset+0x238/0x340 [mpt3sas]
 [<ffffffffc04f794d>] mpt3sas_base_hard_reset_handler+0x1ad/0x420 [mpt3sas]
 [<ffffffffc05132b9>] _ctl_ioctl_main.isra.12+0x11b9/0x1200 [mpt3sas]
 [<ffffffffc068d585>] ? xfs_file_aio_write+0x155/0x1b0 [xfs]
 [<ffffffff9ca1a4e3>] ? do_sync_write+0x93/0xe0
 [<ffffffffc051337a>] _ctl_ioctl+0x1a/0x20 [mpt3sas]
 [<ffffffff9ca2fe90>] do_vfs_ioctl+0x350/0x560
 [<ffffffff9ca1dec1>] ? __sb_end_write+0x31/0x60
 [<ffffffff9ca30141>] SyS_ioctl+0xa1/0xc0
 [<ffffffff9cf28715>] ? system_call_after_swapgs+0xa2/0x146
 [<ffffffff9cf287d5>] system_call_fastpath+0x1c/0x21
 [<ffffffff9cf28721>] ? system_call_after_swapgs+0xae/0x146
---[ end trace 5dac5b98d89aaa3c ]---
------------[ cut here ]------------
kernel BUG at block/blk-core.c:1476!
invalid opcode: 0000 [#1] SMP
Modules linked in: macsec tcp_diag udp_diag inet_diag unix_diag af_packet_diag netlink_diag binfmt_misc fuse xt_CHECKSUM ipt_MASQUERADE nf_nat_masquerade_ipv4 tun devlink ip6t_rpfilter ipt_REJECT nf_reject_ipv4 ip6t_REJECT nf_reject_ipv6 xt_conntrack ip_set nfnetlink ebtable_nat ebtable_broute bridge stp llc ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter sunrpc vfat fat sb_edac intel_powerclamp coretemp intel_rapl iosf_mbi kvm_intel kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd iTCO_wdt iTCO_vendor_support
 dcdbas pcspkr joydev ipmi_ssif ses enclosure sg ipmi_devintf acpi_pad ipmi_msghandler acpi_power_meter mei_me lpc_ich wmi mei shpchp ip_tables xfs libcrc32c sd_mod crc_t10dif crct10dif_generic ata_generic pata_acpi uas usb_storage mgag200 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm ata_piix mpt3sas libata crct10dif_pclmul crct10dif_common tg3 crc32c_intel i2c_core raid_class ptp scsi_transport_sas pps_core dm_mirror dm_region_hash dm_log dm_mod
CPU: 12 PID: 4336 Comm: python Kdump: loaded Tainted: G        W      ------------   3.10.0-875.el7.brdc.x86_64 #1
Hardware name: Dell Inc. PowerEdge R820/0YWR73, BIOS 1.5.0 03/08/2013
task: ffff903fc96e0fd0 ti: ffff903fb1eec000 task.ti: ffff903fb1eec000
RIP: 0010:[<ffffffff9cb19ec0>]  [<ffffffff9cb19ec0>] blk_requeue_request+0x90/0xa0
RSP: 0018:ffff903c6b783dc0  EFLAGS: 00010087
RAX: ffff903bb67026d0 RBX: ffff903b7d6a6140 RCX: dead000000000200
RDX: ffff903bb67026d0 RSI: ffff903bb6702580 RDI: ffff903bb67026d0
RBP: ffff903c6b783dd8 R08: ffff903bb67026d0 R09: ffffd97e80000000
R10: ffff903c658bac00 R11: 0000000000000000 R12: ffff903bb6702580
R13: ffff903fa9a292f0 R14: 0000000000000246 R15: 0000000000001057
FS:  00007f7026f5b740(0000) GS:ffff903c6b780000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f298877c004 CR3: 00000000caf36000 CR4: 00000000000607e0
Call Trace:
 <IRQ>
 [<ffffffff9cca68ff>] __scsi_queue_insert+0xbf/0x110
 [<ffffffff9cca79ca>] scsi_io_completion+0x5da/0x6a0
 [<ffffffff9cc9ca3c>] scsi_finish_command+0xdc/0x140
 [<ffffffff9cca6aa2>] scsi_softirq_done+0x132/0x160
 [<ffffffff9cb240c6>] blk_done_softirq+0x96/0xc0
 [<ffffffff9c89a905>] __do_softirq+0xf5/0x280
 [<ffffffff9cf2bd2c>] call_softirq+0x1c/0x30
 [<ffffffff9c82d625>] do_softirq+0x65/0xa0
 [<ffffffff9c89ac85>] irq_exit+0x105/0x110
 [<ffffffff9cf2d0a8>] smp_apic_timer_interrupt+0x48/0x60
 [<ffffffff9cf297f2>] apic_timer_interrupt+0x162/0x170
 <EOI>
 [<ffffffff9cca5f41>] ? scsi_done+0x21/0x60
 [<ffffffff9cb5ac18>] ? delay_tsc+0x38/0x60
 [<ffffffff9cb5ab5d>] __const_udelay+0x2d/0x30
 [<ffffffffc04effde>] _base_handshake_req_reply_wait+0x8e/0x4a0 [mpt3sas]
 [<ffffffffc04f0b13>] _base_get_ioc_facts+0x123/0x590 [mpt3sas]
 [<ffffffffc04f06c8>] ? _base_diag_reset+0x238/0x340 [mpt3sas]
 [<ffffffffc04f7993>] mpt3sas_base_hard_reset_handler+0x1f3/0x420 [mpt3sas]
 [<ffffffffc05132b9>] _ctl_ioctl_main.isra.12+0x11b9/0x1200 [mpt3sas]
 [<ffffffffc068d585>] ? xfs_file_aio_write+0x155/0x1b0 [xfs]
 [<ffffffff9ca1a4e3>] ? do_sync_write+0x93/0xe0
 [<ffffffffc051337a>] _ctl_ioctl+0x1a/0x20 [mpt3sas]
 [<ffffffff9ca2fe90>] do_vfs_ioctl+0x350/0x560
 [<ffffffff9ca1dec1>] ? __sb_end_write+0x31/0x60
 [<ffffffff9ca30141>] SyS_ioctl+0xa1/0xc0
 [<ffffffff9cf28715>] ? system_call_after_swapgs+0xa2/0x146
 [<ffffffff9cf287d5>] system_call_fastpath+0x1c/0x21
 [<ffffffff9cf28721>] ? system_call_after_swapgs+0xae/0x146
Code: 83 c3 10 4c 89 e2 4c 89 ee e8 8d 21 04 00 48 8b 03 48 85 c0 75 e5 41 f6 44 24 4a 10 74 ad 4c 89 e6 4c 89 ef e8 b2 42 00 00 eb a0 <0f> 0b 0f 1f 40 00 66 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90
RIP  [<ffffffff9cb19ec0>] blk_requeue_request+0x90/0xa0
 RSP <ffff903c6b783dc0>

As a part of host reset operation, driver will flushout all IOs outstanding
at driver level with "DID_RESET" result.  To find which are all commands
outstanding at the driver level, driver loops with smid starting from one
to HBA queue depth and calls mpt3sas_scsih_scsi_lookup_get() to get scmd as
shown below

 for (smid = 1; smid <= ioc->scsiio_depth; smid++) {
                scmd = mpt3sas_scsih_scsi_lookup_get(ioc, smid);
                if (!scmd)
                        continue;

But in mpt3sas_scsih_scsi_lookup_get() function, driver returns some scsi
cmnds which are not outstanding at the driver level (possibly request is
constructed at block layer since QUEUE_FLAG_QUIESCED is not set. Even if
driver uses scsi_block_requests and scsi_unblock_requests, issue still
persists as they will be just blocking further IO from scsi layer and not
from block layer) and these commands are flushed with DID_RESET host bytes
thus resulting into above kernel BUG.

This issue got introduced by commit dbec4c90 ("scsi: mpt3sas: lockless
command submission").

To fix this issue, we have modified the mpt3sas_scsih_scsi_lookup_get() to
check for smid equals to zero (note: whenever any scsi cmnd is processing
at the driver level then smid for that scsi cmnd will be non-zero, always
it starts from one) before it returns the scmd pointer to the caller. If
smid is zero then this function returns scmd pointer as NULL and driver
won't flushout those scsi cmnds at driver level with DID_RESET host byte
thus this issue will not be observed.

[mkp: amended with updated fix from Sreekanth]
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com>
Fixes: dbec4c90 ("scsi: mpt3sas: lockless command submission")
Cc: stable@vger.kernel.org # v4.16+
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Reviewed-by: NBart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Swap the I/O memory read value back to cpu endianness before storing it in
a data structures which are defined in the MPI headers where u8 components
are not defined in the endianness order.

In this area from day one mpt3sas driver is using le32_to_cpu() &
cpu_to_le32() APIs. But in commit cf6bf971
(mpt3sas: Bug fix for big endian systems) we have removed these APIs
before reading I/O memory which we should haven't done it. So
in this patch I am correcting it by adding these APIs back
before accessing I/O memory.
Signed-off-by: NSreekanth Reddy <sreekanth.reddy@broadcom.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently this function is implemented in the scsi layer, but it's
actual place should be the block layer since T10-PI is a general
data integrity feature that is used in the nvme protocol as well.
Suggested-by: NChristoph Hellwig <hch@lst.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMax Gurtovoy <maxg@mellanox.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Commit cf6bf971 ("scsi: mpt3sas: Bug fix for big endian systems") was
merged to address sparse warnings. However, the patch introduced a
regression on big endian since the code accidentally mixed I/O memory
accessors, which do endian swaps, and regular CPU loads and stores.

Do a partial revert of the offending commit.

[mkp: replaced commit message]
Signed-off-by: NChaitra P B <chaitra.basappa@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

No functional change.

Just introduce scsi_host_busy() and replace the direct read of
scsi_host->host_busy with this new API.

Cc: Omar Sandoval <osandov@fb.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: NMing Lei <ming.lei@redhat.com>
Reviewed-by: NBart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Avoids that warnings about the kernel headers appear when building with
W=1. Remove useless "@Returns - Nothing" clauses. Change "@Return - " into
"Return: ".
Signed-off-by: NBart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

scsi: mpt3sas: Split _base_reset_handler(), mpt3sas_scsih_reset_handler() and mpt3sas_ctl_reset_handler()

Split each of these functions in three functions - one function per reset
phase. This patch does not change any functionality but makes the code
easier to read.

Note: it is much easier to review the git diff -w output after having
applied this patch than by reviewing the patch itself.
Signed-off-by: NBart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Since ioc->shost_recovery is set after ioc->reset_in_progress_mutex is
obtained, if concurrent resets are issued there is a short time during
which ioc->reset_in_progress_mutex is locked and ioc->shost_recovery ==
0. Avoid that this can cause trouble by unconditionally locking
ioc->shost_recovery.
Signed-off-by: NBart Van Assche <bart.vanassche@wdc.com>
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Chaitra P B <chaitra.basappa@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>