To be able to use the driver on other OF-aware architectures, too.
And add necessary OF related #includes to fix compilation error.
Signed-off-by: NJoachim Foerster <joachim.foerster@missinglinkelectronics.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some Stellaris evaluation kits have the JTAG/SWD FTDI chip onboard,
and some, like EK-LM3S9B90, come with a separate In-Circuit Debugger
Interface Board. The ICDI board can also be used stand-alone, for
other boards and chips than the kit it came with. The ICDI has both
old style 20-pin JTAG connector and new style JTAG/SWD 10-pin 1.27mm
pitch connector.

Tested with EK-LM3S9B90, where the BD-ICDI board is included.
Signed-off-by: NPeter Stuge <peter@stuge.se>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

At least some OHCI hardware (such as the MCP89) fails to flag any change
in the host status register or the port status registers when receiving
a remote wakeup while in D3 state. This results in the controller being
resumed but no device state change being noticed, at which point the
controller is put back to sleep again. Since there doesn't seem to be any
reliable way to identify the state change, just unconditionally resume the
hub. It'll be put back to sleep in the near future anyway if there are no
active devices attached to it.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Cc: stable <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

To add USB 3.0 link power management (LPM), we need to know what the U1
and U2 exit latencies are for the xHCI host controller.  External USB 3.0
hubs report these values through the SuperSpeed Capabilities descriptor in
the BOS descriptor.  Make the USB 3.0 roothub for the xHCI host behave
like an external hub and return the BOS descriptors.

The U1 and U2 exit latencies will vary across each host controller, so we
need to dynamically fill those values in by reading the exit latencies out
of the xHC registers.  Make the roothub code in the USB core handle
hub_control() returning the length of the data copied.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This driver provides two functions in one configuration:
a mass storage, and a ACM (serial port) link.
Heavily based on multi.c and cdc2.c
Signed-off-by: NKlaus Schwarzkopf <schwarzkopf@sensortherm.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

| drivers/usb/gadget/mv_udc_core.c: In function 'handle_setup_packet':
| drivers/usb/gadget/mv_udc_core.c:1556:6: warning: 'status' may be \
	used uninitialized in this function
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch is going to support clock gating when vbus detection is
posible. Clock and phy will be on only when usb gadget is used(vbus valid).
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add test mode support for marvell udc driver.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

use DMA API for status_req's dma address, it is needed by dtd.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The controller will prime failure sometimes when do the iperf test.
Add delay to wait controller release dtd dma before we free it.
Then the issue is gone.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

put the device in idle when shutdown.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch is going to correct the ep0 state, and the unexpected
ep0 package warning can be removed.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

1: Add parameter check.
2: For controller endpoint, we need to flush in and out directions.
3: delete redundant code, make it more readable.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

According to the comment right above the code, we should use
USB_ENDPOINT_XFER_BULK instead.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The ep enable / disable functions can be called from interrupt
context, and they are not race safe on SMP systems. The critical
data can be modified in more than one routing.
Make them race safe by using IRQ-safe spinlock functions.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

For the code doesn't restrict controller ep must be ep0, so we will go
through all the eps and check if there is a setup package received.
And also we just need to acknowledge the corresponding bit in
ENDPTSETUPSTAT register.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Set next dtd ptr to EP_QUEUE_HEAD_NEXT_TERMINATE for dqh when init ep0.
It means the dQH is empty.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

According to ChipIdea datasheet, there is no toggle flag for ep0.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The max size of data payload is in bit0 - bit10, so we need use 0x7ff
as the bitmask to fetch from usb_endpoint_descriptor.wMaxPacketSize.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some platforms will use usb to download images, the controller may not
be stopped correctly when start kernel. In some cases, it may have some
pending interrupts, and they will be triggered immediately when we finish
requesting irq in function probe. But we haven't finished the device
initialization at this time. So let's stop udc here to avoid this case
occurred.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Tag the probe function as __devinit.
Tag the remove function as __devexit.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch do the following things:

1. Add header and Copyright for marvell usb driver.
2. Add mv_usb.h in include/linux/platform_data, make the driver
   fits all the marvell platform using the same ChipIdea usb ip.
3. Some SOC may has mutiple clock sources, so let me define it
   in mv_usb_platform_data and give two helper functions named
   udc_clock_enable/udc_clock_disable to deal with the clocks.
4. Different SOCs will have some difference in PHY initialization,
   so we will remove file mv_udc_phy.c and add two funtions in
   mv_usb_platform_data, let the platform relative driver to realize it.
5. Rewrite probe function according to the modification list above. Find
   it will kernel panic when probe failed. The root cause is as follows:
	When probe failed, the error handle may call device_unregister()
	which in return will call gadget_release.In current code,
	gadget_release have two issues:
		1: the_controller is a NULL pointer.
		2: if we free udc here, then the following code in probe
		   will access NULL pointer.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

| drivers/usb/renesas_usbhs/fifo.c: In function ‘usbhsf_dma_prepare_push’:
| drivers/usb/renesas_usbhs/fifo.c:823:7: warning: cast from pointer \
	to integer of different size [-Wpointer-to-int-cast]
| drivers/usb/renesas_usbhs/fifo.c: In function ‘usbhsf_dma_try_pop’:
| drivers/usb/renesas_usbhs/fifo.c:900:7: warning: cast from pointer \
	to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: NFelipe Balbi <balbi@ti.com>

that driver can compile cleanly on x86 without
any issues.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In current renesas-usbhs,
there was inconsistency about the style of kernel module or built-in.
This patch solve it.

[ balbi@ti.com : fix compile issue when building modules ]
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

renesas_usbhs has default callback functions and settings.
And it tried overwrite to platform private data
if platform doesn't have them.
So, if renesas_usbhs was compiled as module,
it will be hung-up on 2nd insmod.
This patch fixup it.
Special thanks to Bastian
Reported-by: NBastian Hecht <hechtb@googlemail.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This is mod_host prototype support for renesas_usbhs driver.
It doesn't support USB-Hub, and USB-DMAC for now.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

CCPL setting is needed on only mod_gadget.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

mod_host needs data/status stage handler
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

mod_host use INTSTS1 interrupt
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

mod_host needs device speed setup function
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It is enabled to set SOF packet output bit when USBRST bit was set.
And USBRST bit should be set 0 when SOF packet was output.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

some renesas_usbhs device is supporting OTG external device interface.
In that device, it is necessary to control PWEN/EXTLP on DVSTCTR.
This patch support it.
But renesas_usbhs driver doesn't have OTG support for now.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When data read interrupt happened, the pipe is BUF which means "enable".
then, next un-necessary interrupt/token might be
issued again when all data were popped from fifo.
It will cause un-understandable bug.
This patch decides pipe disable on top of read interrupt.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

renesas_usbhs can manually set DATA0/DATA1.
This patch is prepare for mod_host support
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Automatically packet start by usbhs_pkt_push() was useful.
But the pushed packet will be called twice
if new packet was pushed on usbhs_pkt :: done callback.
(1st is called by usbhs_pkt_push(), 2nd is called by usbhsf_pkt_handler())

This patch disables automatic packet start,
and clarified packet start timing.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

transfer done function was registered in struct struct usbhs_pipe_info.
It was good for mod_gadget, but not good for mod_host.
This function move it to struct usbhs_pkt.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

pipe name is usefull function for mod_xxx
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

device select method will be used on mod_host
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There was no method to get struct usbhs_priv when
packet transfer done function was called.
This patch allow that callback function receive it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>