pci_pm_suspend_noirq() and pci_pm_resume_noirq() already handle power
transition for system-wide suspend and resume, so it's not necessary to
do it in the driver.
Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The blamed commit changed the vlan used by the host ports to be 4095
instead of 0.
Because of this change the following issues are seen:
- when the port is probed first it was adding an entry in the MAC table
  with the wrong vlan (port->pvid which is default 0) and not HOST_PVID
- when the port is removed from a bridge, it was using the wrong vlan to
  add entries in the MAC table. It was using the old PVID and not the
  HOST_PVID

This patch fixes this two issues by using the HOST_PVID instead of
port->pvid.

Fixes: 6d2c186a ("net: lan966x: Add vlan support.")
Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Update for net-next

This series includes some added error logging for firmware error reports,
DIM interrupt sampling for the latest 5750X chips, CQE interrupt
coalescing mode support, and to use RX page frag buffers for better
software GRO performance.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If NETIF_F_GRO_HW is disabled, the existing driver code uses kmalloc'ed
data for RX buffers.  This causes inefficient SW GRO performance
because the GRO data is merged using the less efficient frag_list.
Use netdev_alloc_frag() and friends instead so that GRO data can be
merged into skb_shinfo(skb)->frags for better performance.

[Use skb_free_frag() - Vikas Gupta]
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NPavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NVikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The xdp_do_flush_map function has been replaced with the more general
xdp_do_flush().
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support showing and setting the CQE mode in ethtool.
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CQE coalescing mode is the same as the timer reset coalescing mode
on Broadcom devices.  Currently this mode is always enabled if it
is supported by the device.  Restructure the code slightly to support
dynamically changing this mode.

Add a flags field to struct bnxt_coal.  Initially, the CQE flag will
be set for the RX and TX side if the device supports it.  We need to
move bnxt_init_dflt_coal() to set up default coalescing until the
capability is determined.
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

5750X (P5) chips handle receiving packets on the NQ rather than the main
completion queue so we need to get and set stats from the correct spots
for dynamic interrupt moderation.
Signed-off-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Log the unrecognized error report type value as well.
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FW has been modified to send a new async event when it detects
a pause storm. Register for this new event and log it upon receipt.
Reviewed-by: NAndy Gospodarek <gospo@broadcom.com>
Reviewed-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use 'bitmap_zalloc()' to simplify code, improve the semantic and reduce
some open-coded arithmetic in allocator arguments.

Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/f9541b085ec68e573004e1be200c11c9c901181a.1640295165.git.christophe.jaillet@wanadoo.frSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Add config_init for LAN8814. This function is required for the following
reasons:
- we need to make sure that the PHY is reset,
- disable ANEG with QSGMII PCS Host side
- swap the MDI-X A,B transmit so that there will not be any link flip-flaps
  when the PHY gets a link.
Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the possessive "its" instead of the contraction of "it is" ("it's")
in user messages.
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include/net/sock.h
  commit 8f905c0e ("inet: fully convert sk->sk_rx_dst to RCU rules")
  commit 43f51df4 ("net: move early demux fields close to sk_refcnt")
  https://lore.kernel.org/all/20211222141641.0caa0ab3@canb.auug.org.au/Signed-off-by: NJakub Kicinski <kuba@kernel.org>

ETHER_CLK_SEL_FREQ_SEL_2P5M is not 0 bit of the register. This is a
value, which is 0. Fix from BIT(0) to 0.
Reported-by: NYuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Fixes: b38dd98f ("net: stmmac: Add Toshiba Visconti SoCs glue driver")
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://lore.kernel.org/r/20211223073633.101306-1-nobuhiro1.iwamatsu@toshiba.co.jpSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Hayes Wang says:

====================
r8152: fix bugs

Patch #1 fix the issue of force speed mode for RTL8156.
Patch #2 fix the issue of unexpected ocp_base.
====================

Link: https://lore.kernel.org/r/20211223092702.23841-386-nic_swsd@realtek.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

There are some chances that the actual base of hardware is different
from the value recorded by driver, so we have to reset the variable
of ocp_base to sync it.

Set ocp_base to -1. Then, it would be updated and the new base would be
set to the hardware next time.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

It needs to set mdio force mode. Otherwise, link off always occurs when
setting force speed.

Fixes: 195aae32 ("r8152: support new chips")
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Commit 561d8352 ("bridge: use ndo_siocdevprivate") changed the
source and destination arguments of copy_{to,from}_user in bridge's
old_deviceless() from args[1] to uarg breaking SIOC{G,S}IFBR ioctls.

Commit cbd7ad29 ("net: bridge: fix ioctl old_deviceless bridge
argument") fixed only BRCTL_{ADD,DEL}_BRIDGES commands leaving
BRCTL_GET_BRIDGES one untouched.

The fixes BRCTL_GET_BRIDGES as well and has been tested with busybox's
brctl.

Example of broken brctl:
$ brctl show
bridge name     bridge id               STP enabled     interfaces
brctl: can't get bridge name for index 0: No such device or address

Example of fixed brctl:
$ brctl show
bridge name     bridge id               STP enabled     interfaces
br0             8000.000000000000       no

Fixes: 561d8352 ("bridge: use ndo_siocdevprivate")
Signed-off-by: NRemi Pommarel <repk@triplefau.lt>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NNikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/all/20211223153139.7661-2-repk@triplefau.lt/Signed-off-by: NJakub Kicinski <kuba@kernel.org>

Convert the u32 variable to type u64 in a context where expression of
type u64 is required to avoid potential overflow.

Fixes: e9e37200 ("net: stmmac: ptp: update tas basetime after ptp adjust")
Signed-off-by: NXiaoliang Yang <xiaoliang.yang_1@nxp.com>
Link: https://lore.kernel.org/r/20211223073928.37371-1-xiaoliang.yang_1@nxp.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

For Ocelot switches, the CPU injected frames have an injection header
where it can specify the QoS class of the packet and the DSA tag, now it
uses the SKB priority to set that. If a traffic class to priority
mapping is configured on the netdevice (with mqprio for example ...), it
won't be considered for CPU injected headers. This patch make the QoS
class aligned to the priority to traffic class mapping if it exists.

Fixes: 8dce89aa ("net: dsa: ocelot: add tagger for Ocelot/Felix switches")
Signed-off-by: NXiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: NMarouen Ghodhbane <marouen.ghodhbane@nxp.com>
Link: https://lore.kernel.org/r/20211223072211.33130-1-xiaoliang.yang_1@nxp.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

After commit d3256efd ("veth: allow enabling NAPI even without XDP"),
if GRO is enabled on a veth device and TSO is disabled on the peer
device, TCP skbs will go through the NAPI callback. If there is no XDP
program attached, the veth code does not perform any share check, and
shared/cloned skbs could enter the GRO engine.

Ignat reported a BUG triggered later-on due to the above condition:

[   53.970529][    C1] kernel BUG at net/core/skbuff.c:3574!
[   53.981755][    C1] invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
[   53.982634][    C1] CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 5.16.0-rc5+ #25
[   53.982634][    C1] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015
[   53.982634][    C1] RIP: 0010:skb_shift+0x13ef/0x23b0
[   53.982634][    C1] Code: ea 03 0f b6 04 02 48 89 fa 83 e2 07 38 d0
7f 08 84 c0 0f 85 41 0c 00 00 41 80 7f 02 00 4d 8d b5 d0 00 00 00 0f
85 74 f5 ff ff <0f> 0b 4d 8d 77 20 be 04 00 00 00 4c 89 44 24 78 4c 89
f7 4c 89 8c
[   53.982634][    C1] RSP: 0018:ffff8881008f7008 EFLAGS: 00010246
[   53.982634][    C1] RAX: 0000000000000000 RBX: ffff8881180b4c80 RCX: 0000000000000000
[   53.982634][    C1] RDX: 0000000000000002 RSI: ffff8881180b4d3c RDI: ffff88810bc9cac2
[   53.982634][    C1] RBP: ffff8881008f70b8 R08: ffff8881180b4cf4 R09: ffff8881180b4cf0
[   53.982634][    C1] R10: ffffed1022999e5c R11: 0000000000000002 R12: 0000000000000590
[   53.982634][    C1] R13: ffff88810f940c80 R14: ffff88810f940d50 R15: ffff88810bc9cac0
[   53.982634][    C1] FS:  0000000000000000(0000) GS:ffff888235880000(0000) knlGS:0000000000000000
[   53.982634][    C1] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   53.982634][    C1] CR2: 00007ff5f9b86680 CR3: 0000000108ce8004 CR4: 0000000000170ee0
[   53.982634][    C1] Call Trace:
[   53.982634][    C1]  <TASK>
[   53.982634][    C1]  tcp_sacktag_walk+0xaba/0x18e0
[   53.982634][    C1]  tcp_sacktag_write_queue+0xe7b/0x3460
[   53.982634][    C1]  tcp_ack+0x2666/0x54b0
[   53.982634][    C1]  tcp_rcv_established+0x4d9/0x20f0
[   53.982634][    C1]  tcp_v4_do_rcv+0x551/0x810
[   53.982634][    C1]  tcp_v4_rcv+0x22ed/0x2ed0
[   53.982634][    C1]  ip_protocol_deliver_rcu+0x96/0xaf0
[   53.982634][    C1]  ip_local_deliver_finish+0x1e0/0x2f0
[   53.982634][    C1]  ip_sublist_rcv_finish+0x211/0x440
[   53.982634][    C1]  ip_list_rcv_finish.constprop.0+0x424/0x660
[   53.982634][    C1]  ip_list_rcv+0x2c8/0x410
[   53.982634][    C1]  __netif_receive_skb_list_core+0x65c/0x910
[   53.982634][    C1]  netif_receive_skb_list_internal+0x5f9/0xcb0
[   53.982634][    C1]  napi_complete_done+0x188/0x6e0
[   53.982634][    C1]  gro_cell_poll+0x10c/0x1d0
[   53.982634][    C1]  __napi_poll+0xa1/0x530
[   53.982634][    C1]  net_rx_action+0x567/0x1270
[   53.982634][    C1]  __do_softirq+0x28a/0x9ba
[   53.982634][    C1]  run_ksoftirqd+0x32/0x60
[   53.982634][    C1]  smpboot_thread_fn+0x559/0x8c0
[   53.982634][    C1]  kthread+0x3b9/0x490
[   53.982634][    C1]  ret_from_fork+0x22/0x30
[   53.982634][    C1]  </TASK>

Address the issue by skipping the GRO stage for shared or cloned skbs.
To reduce the chance of OoO, try to unclone the skbs before giving up.

v1 -> v2:
 - use avoid skb_copy and fallback to netif_receive_skb  - Eric
Reported-by: NIgnat Korchagin <ignat@cloudflare.com>
Fixes: d3256efd ("veth: allow enabling NAPI even without XDP")
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Tested-by: NIgnat Korchagin <ignat@cloudflare.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/b5f61c5602aab01bac8d711d8d1bfab0a4817db7.1640197544.git.pabeni@redhat.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.17

Third set of patches for v5.17, and the final one if all goes well. We
have Specific Absorption Rate (SAR) support for both mt76 and rtw88.
Also iwlwifi should be now W=1 warning free. But otherwise nothing
really special this time, business as usual.

Major changes:

mt76
 * Specific Absorption Rate (SAR) support
 * mt7921: new PCI ids
 * mt7921: 160 MHz channel support

iwlwifi
 * fix W=1 and sparse warnings
 * BNJ hardware support
 * add new killer device ids
 * support for Time-Aware-SAR (TAS) from the BIOS
 * Optimized Connectivity Experience (OCE) scan support

rtw88
 * hardware scan
 * Specific Absorption Rate (SAR) support

ath11k
 * qca6390/wcn6855: report signal and tx bitrate
 * qca6390: rfkill support
 * qca6390/wcn6855: regdb.bin support

ath5k
 * switch to rate table based lookup

wilc1000
 * spi: reset/enable GPIO support

* tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (148 commits)
  mt76: mt7921: fix a possible race enabling/disabling runtime-pm
  wilc1000: Document enable-gpios and reset-gpios properties
  wilc1000: Add reset/enable GPIO support to SPI driver
  wilc1000: Convert static "chipid" variable to device-local variable
  rtw89: 8852a: correct bit definition of dfs_en
  rtw88: don't consider deep PS mode when transmitting packet
  ath11k: Fix unexpected return buffer manager error for QCA6390
  ath11k: add support of firmware logging for WCN6855
  ath11k: Fix napi related hang
  ath10k: replace strlcpy with strscpy
  rtw88: support SAR via kernel common API
  rtw88: 8822c: add ieee80211_ops::hw_scan
  iwlwifi: mei: wait before mapping the shared area
  iwlwifi: mei: clear the ownership when the driver goes down
  iwlwifi: yoyo: fix issue with new DBGI_SRAM region read.
  iwlwifi: fw: fix some scan kernel-doc
  iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ
  iwlwifi: mvm: remove card state notification code
  iwlwifi: mvm: drop too short packets silently
  iwlwifi: mvm: fix AUX ROC removal
  ...
====================

Link: https://lore.kernel.org/r/20211223141108.78808C36AE9@smtp.kernel.orgSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Amit Cohen says:

====================
mlxsw: Add tests for VxLAN with IPv6 underlay

mlxsw driver lately added support for VxLAN with IPv6 underlay.
This set adds tests for IPv6, which are dedicated for mlxsw.

Patch set overview:
Patches #1-#2 make vxlan.sh test more flexible and extend it for IPv6
Patches #3-#4 make vxlan_fdb_veto.sh test more flexible and extend it
for IPv6
Patches #5-#6 add tests for VxLAN flooding for different ASICs
Patches #7-#8 add test for VxLAN related traps and align the existing
test
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the case that sends packets with "too short inner packet" to
include part of ethernet header, to make the trap to be triggered due to
the correct reason.

According to ASIC arch, the trap is triggered if overlay packet length is
less than 18B, and the minimum inner packet should include source MAC and
destination MAC.

Till now the case passed because one of the reserved bits in VxLAN
header was used. This issue was found while adding an equivalent test
for IPv6.
Signed-off-by: NAmit Cohen <amcohen@nvidia.com>
Reviewed-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The test configures VxLAN with IPv6 underlay and verifies that the
expected traps are triggered under the right conditions.

The test is similar to the existing IPv4 test.
Signed-off-by: NAmit Cohen <amcohen@nvidia.com>
Reviewed-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.

The number of records is changed according to ASIC type and address
family.

Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-2 and above, which support up to four
IPv6 addresses in one record.

The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: NAmit Cohen <amcohen@nvidia.com>
Reviewed-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device stores flood records in a singly linked list where each
record stores up to X IP addresses of remote VTEPs.

The number of records is changed according to ASIC type and address
family.

Add a test which is similar to the existing IPv4 test to check IPv6.
The test is dedicated for Spectrum-1 switches, which support up to five
IPv6 addresses in one record.

The test verifies that packets are correctly flooded in various cases such
as deletion of a record in the middle of the list.
Signed-off-by: NAmit Cohen <amcohen@nvidia.com>
Reviewed-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add test to verify FDB vetos of VxLAN with IPv6 underlay.
Use the existing test which checks IPv4.
Signed-off-by: NAmit Cohen <amcohen@nvidia.com>
Reviewed-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vxlan_fdb_veto.sh cases are dedicated to test VxLAN with IPv4 underlay.
The main changes to test IPv6 underlay are IP addresses and some flags.

Add variables to define all the values which supposed to be different
for IPv6 testing, set them to use the existing values by default.

The next patch will define the new added variables in a separated file,
so the same tests can be used for IPv6 also.
Signed-off-by: NAmit Cohen <amcohen@nvidia.com>
Reviewed-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add test to verify configuration of VxLAN with IPv6 underlay.
Use the existing test which checks IPv4.

Add separated test cases for learning which is not supported for IPv6
and for UDP checksum flags which are different from IPv4 flags.
Signed-off-by: NAmit Cohen <amcohen@nvidia.com>
Reviewed-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

vxlan.sh cases are dedicated to test VxLAN with IPv4 underlay.
The main changes to test IPv6 underlay are IP addresses and some flags.

Add variables to define all the values which supposed to be different
for IPv6 testing, set them to use the existing values by default.

The next patch will define the new added variables in a separated file,
so the same tests can be used for IPv6 also.

Rename some functions to include "ipv4", so the next patch will add
equivalent functions for IPv6.
Signed-off-by: NAmit Cohen <amcohen@nvidia.com>
Reviewed-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.

Replace kernel.h inclusion with the list of what is really being used.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NSergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds basic support for EtherType RX frame steering for
LLDP and PTP using the hardware offload capabilities.

Example steps for setting up RX frame steering for LLDP and PTP:
$ IFDEVNAME=eth0
$ tc qdisc add dev $IFDEVNAME ingress
$ tc qdisc add dev $IFDEVNAME root mqprio num_tc 8 \
     map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \
     queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0

For LLDP
$ tc filter add dev $IFDEVNAME parent ffff: protocol 0x88cc \
     flower hw_tc 5
OR
$ tc filter add dev $IFDEVNAME parent ffff: protocol LLDP \
     flower hw_tc 5

For PTP
$ tc filter add dev $IFDEVNAME parent ffff: protocol 0x88f7 \
     flower hw_tc 6

Show tc ingress filter
$ tc filter show dev $IFDEVNAME ingress

v1->v2:
 Thanks to Kurt's and Sebastian's suggestion.
 - change from __be16 to u16 etype
 - change ETHER_TYPE_FULL_MASK to use cpu_to_be16() macro
Signed-off-by: NOng Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch series extends the current supported bridge flags with the
following flags: BR_FLOOD, BR_BCAST_FLOOD and BR_LEARNING.
Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix suspicious rcu_dereference_protected() usage when offloading tc action.

We should hold tcfa_lock to offload tc action in action initiation.

Without these changes, the following warning will be observed:

WARNING: suspicious RCU usage
5.16.0-rc5-net-next-01504-g7d1f236dcffa-dirty #50 Tainted: G          I
-----------------------------
include/net/tc_act/tc_tunnel_key.h:33 suspicious rcu_dereference_protected() usage!
1 lock held by tc/12108:
CPU: 4 PID: 12108 Comm: tc Tainted: G
Hardware name: Dell Inc. PowerEdge R740/07WCGN, BIOS 1.6.11 11/20/2018
Call Trace:
<TASK>
dump_stack_lvl+0x49/0x5e
dump_stack+0x10/0x12
lockdep_rcu_suspicious+0xed/0xf8
tcf_tunnel_key_offload_act_setup+0x1de/0x300 [act_tunnel_key]
tcf_action_offload_add_ex+0xc0/0x1f0
tcf_action_init+0x26a/0x2f0
tcf_action_add+0xa9/0x1f0
tc_ctl_action+0xfb/0x170
rtnetlink_rcv_msg+0x169/0x510
? sched_clock+0x9/0x10
? rtnl_newlink+0x70/0x70
netlink_rcv_skb+0x55/0x100
rtnetlink_rcv+0x15/0x20
netlink_unicast+0x1a8/0x270
netlink_sendmsg+0x245/0x490
sock_sendmsg+0x65/0x70
____sys_sendmsg+0x219/0x260
? __import_iovec+0x2c/0x150
___sys_sendmsg+0xb7/0x100
? __lock_acquire+0x3d5/0x1f40
? __this_cpu_preempt_check+0x13/0x20
? lock_is_held_type+0xe4/0x140
? sched_clock+0x9/0x10
? ktime_get_coarse_real_ts64+0xbe/0xd0
? __this_cpu_preempt_check+0x13/0x20
? lockdep_hardirqs_on+0x7e/0x100
? ktime_get_coarse_real_ts64+0xbe/0xd0
? trace_hardirqs_on+0x2a/0xf0
__sys_sendmsg+0x5a/0xa0
? syscall_trace_enter.constprop.0+0x1dd/0x220
__x64_sys_sendmsg+0x1f/0x30
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f4db7bb7a60

Fixes: 8cbfe939 ("flow_offload: allow user to offload tc action to net device")
Reported-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NBaowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: NLouis Peens <louis.peens@corigine.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Struct sctp_ep_common is included in both asoc and ep, but hlist_node
and hashent are only needed by ep after asoc_hashtable was dropped by
Commit b5eff712 ("sctp: drop the old assoc hashtable of sctp").

So it is better to move hlist_node and hashent from sctp_ep_common to
sctp_endpoint, and it saves some space for each asoc.
Signed-off-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Amit Cohen says:

====================
Add tests for VxLAN with IPv6 underlay

mlxsw driver lately added support for VxLAN with IPv6 underlay.
This set adds the relevant tests for IPv6, most of them are same to
IPv4 tests with the required changes.

Patch set overview:
Patch #1 relaxes requirements for offloading TC filters that
match on 802.1q fields. The following selftests make use of these
newly-relaxed filters.
Patch #2 adds preparation as part of selftests API, which will be used
later.
Patches #3-#4 add tests for VxLAN with bridge aware and unaware.
Patche #5 cleans unused function.
Patches #6-#7 add tests for VxLAN symmetric and asymmetric.
Patch #8 adds test for Q-in-VNI.
====================

Link: https://lore.kernel.org/r/20211221144949.2527545-1-amcohen@nvidia.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

Add test to check Q-in-VNI traffic with IPv6 underlay and overlay.
The test is similar to the existing IPv4 test.
Signed-off-by: NAmit Cohen <amcohen@nvidia.com>
Reviewed-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

In a similar fashion to the asymmetric test, add a test for symmetric
routing. In symmetric routing both the ingress and egress VTEPs perform
routing in the overlay network into / from the VxLAN tunnel. Packets in
different directions use the same VNI - the L3 VNI.
Different tenants (VRFs) use different L3 VNIs.

Add a test which is similar to the existing IPv4 test to check IPv6.
Signed-off-by: NAmit Cohen <amcohen@nvidia.com>
Reviewed-by: NPetr Machata <petrm@nvidia.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>