The FBIN2FREQ macro and the ath9k_hw_fbin2freq function
does the same thing. Remove the macro, and use the inline
function instead.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Both eeprom.c and ar9003_eeprom.c has an indentical
'ath9k_hw_fbin2freq' function. Move the function to
a common place and remove the duplicates.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The existing constants are used for reduction/increase
tx power level on devices with 2x2 and 3x3 chainmask.

Both reduction and increase must use the same value, so
it makes no sense to use separate constants for them.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The computation of the scaled power value in
various eeprom files uses identical code. Move
that code into a helper function and use that
instead of code duplication.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The REDUCE_SCALED_POWER_BY_THREE_CHAIN symbol is
defined in different eeprom files, and the value
varies between the different files.

In eeprom_def.c and in ar9003_eeprom.c the value
of the symbol is 9, however the comments in these
files indicates the value should be 10*log10(3)*2
which is 9.54242509439325. Replace the the value
to 10 in these files.

Also add comments to eeprom_9287.c.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We have a helper function for updating the max_power_level
value. Use that and remove the duplicated code.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The tx interrupt for beacon queue is configured only for edma chips.
As the edma chip does not support per descriptor interrupt, no need to
set INTREQ for every beacon descriptor. And also clear ps filter for
beacon frame.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Whenever the reset work is queued up, do not generate beacon. And also
clear the beacon miss count once the beacon stuck was observed.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After the chip reset, the noise immunity levels are restored with
history values. If the immunity levels are lower than the defaults,
lets start with the optimal values.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sync-up ibss beacon timer with the beacon frame's timestamp. When the
node acts as joiner, it has to sync with the received beacon timestamp
instead of reading tsf from hw. As the hw tsf wont wont be update till
bssid is configured. This patch programs hw tsf with the received beacon
timestamp if beacon timers are yet to be configured.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update AR9462 initval to fix unbalance beacon distribution
in Ad-Hoc network.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since it's only called when beacons are stuck, move it to the SWBA handler
tasklet, to avoid doing redundant checks on every single interrupt.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

LED support is typically handled via system GPIO on these platforms.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also tweak beacon response times for better stability with the shorter
timer intervals.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Report all defined sync_cause errors in debugfs
to aid with debugging.

Use a macro to print out the interrupts file contents
to decrease code duplication.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This hides some repetitive code, and will help if the
column widths ever need to change.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NRyan Roper <ryan.roper@gmail.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The MAX_TXPWR table for BTCOEX is not needed for AR9462.
Programming these values to the HW results in undesirable
behavior - for example, large number of delimiter/data
underruns are seen in AES-CCMP mode. Also, registers like
AR_PCU_MISC_MODE2 return 0xdeadbeef after the BTCOEX_MAX
power table is programmed to the HW, and frames being transmitted
end up being looped back to the RX engine, an example being beacon
frames in IBSS mode.

Remove this table for now - this fixes CCMP performance and general
IBSS usage.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean up some orphaned code lines containing
* unused variables (not referenced / write-only)
* non-implemented function prototypes
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds counters in various places that can drop packets on
rx without otherwise incrementing a counter.  It also counts
some non-error cases, such as becons and fragments received.

Should help with figuring out where packets are (and are not)
dropped.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This counts any failure during getting packets into
the DMA buffers, including out-of-memory, etc.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Follow updates in DFS pattern detector interface:
a) use given pulse event structure
b) adapt to boolean return value of add_pulse()
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds a DFS pattern detector to ath9k. It is fed with pulse events
by the radar pulse detector and reports in place whether a pattern
was detected. On detection, the result is reported as radar event to
the DFS management component in the upper layer.

Currently the ETSI DFS domain is supported with detector lines for
the patterns defined by EN-301-893 v1.5.1. Support for FCC and JP
will be added gradually.

To include the pattern detector, ath9k must be built with support
for DFS certified config flag set (CONFIG_ATH9K_DFS_CERTIFIED).
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Devices that have internal rate control need to be
notified when the bandwidth or SMPS state changes
just like external rate control algorithms get a
notification now.

Add this notification and clarify the change bits
while at it, the HT_CHANGED bit really meant only
bandwidth changed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The channel type argument to the rate_update()
callback isn't really the correct way to give
the rate control algorithm about the desired
RX bandwidth of the peer.

Remove this argument, and instead update the
STA capabilities with 20/40 appropriately. The
SMPS update done by this callback works in the
same way, so this makes the callback cleaner.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not all devices are really capable of implementing
remain-on-channel, even if it is implemented in SW,
as they can't necessarily deal with channel changes
while associated.

Remove the WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL and add
it only if either the driver has remain_on_channel
implemented in the driver/device.

Also add it to all drivers that advertise P2P right
now since those definitely have to have it working.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use a more current logging style.
Make sure all output is prefixed appropriately.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit c1afdaff.

Users have reported connection failures in 3.3.1 and suspend/resume
failures in 3.4-rcX. Revert this commit for now - PS IDLE can be
fixed in a clean manner later on.

Cc: stable@vger.kernel.org
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the experiment with Azimuth ADEPT-n testbed where the APs transmit
power was reduced to 25% and the signal strength was futher attenuated
by 20dB and induced a path loss of ~7dB, the station was reporting
beacon losses and the following issue were observed.

* rx clear is stuck at low for more than 300ms
* dcu chain and complete state is stuck at one of the hang signature

This patch triggers the hang detection logic that recovers the chip
from any of the above conditions. As the issue was originally reported
in ChromeOs with AR9382 chips, this detection logic is enabled only for
AR9380/2 chips.

Cc: Paul Stewart <pstew@google.com>
Reported-by: NGary Morain <gmorain@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch improves ANI operations by switching among the immunity
levels based on PHY errors and beacon rssi which will adjust receiver
desensitizing parameters. The changes are

* Configure the Weak Signal Detection based on current immunity value.
* At highest OFDM immunity level poor performance was observed with
  strong interference. By tuning the FIR step and spur immunity levels
  and not changing any weak signal detection thresholds at any level
  helped to improve the performance.
* ANI took long time to recover back to lower immunity levels on heavy
  data load. As the listen time got reset to zero before reaching to
  the 5x of aniperiod, the immunity level is not lowering back even
  without any interference. This patch fix that.

Cc: Paul Stewart <pstew@google.com>
Cc: Susinder Gulasekaran <susinder@qca.qualcomm.com>
Signed-off-by: NSuresh Chandrasekaran <csuresh@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op.  This leads to a
proliferation of the default_open() implementation across the entire
tree.

Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().

This replacement was done with the following semantic patch:

<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}

@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>

[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The commit "ath9k: Remove aggregation flags" changed how
nodes were being initialized. Use the HW HT cap bits
to initialize/de-initialize nodes, else we would be
accessing an uninitialized entry during a suspend/resume cycle,
resulting in a panic.
Reported-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit 0d95521e (ath9k: use split rx buffers to get rid of order-1 skb
allocations) added in memory leak in error path.

sc->rx.frag should be cleared after the pskb_expand_head() call, or else
we jump to requeue_drop_frag and leak an skb.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When we have downlink traffic alone and the station is going thru
bgscan, the client is out of operating channel for around 1000ms which
is too long. The mac80211 decides when to switch back to oper channel
based on tx queue, bad latency and listen time. As the station does not
have tx traffic, the bgscan can easily affect downlink throughput. By
reducing the listen time, it helps the associated AP to retain the
downstream rate.

Cc: Paul Stewart <pstew@google.com>
Tested-by: NGary Morain <gmorain@google.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently the maximum noise floor limit is set as too high (-60dB). The
assumption of having a higher threshold limit is that it would help
de-sensitize the receiver (reduce phy errors) from continuous
interference. But when we have a bursty interference where there are
collisions and then free air time and if the receiver is desensitized too
much, it will miss the normal packets too. Lets make use of chips
specific min, nom and max limits always. This patch helps to improve the
connection stability in congested networks.

Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@google.com>
Tested-by: NGary Morain <gmorain@google.com>
Signed-off-by: NMadhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>