This adds hci_le_create_conn_sync and make hci_le_connect use it instead
of queueing multiple commands which may conflict with the likes of
hci_update_passive_scan which uses hci_cmd_sync_queue.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This makes each result entry to be checked using skb_pull_data instead
of acessing them by index.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

syzbot reported that hci_cmd_sync_cancel may sleep from the wrong
context. To avoid this, create a new work item that pushes the relevant
parts into a different context.

Note that we keep the old implementation with the name
__hci_cmd_sync_cancel as the sleeping behaviour is desired in some
cases.

Reported-and-tested-by: syzbot+485cc00ea7cf41dfdbf1@syzkaller.appspotmail.com
Fixes: c97a747e ("Bluetooth: btusb: Cancel sync commands for certain URB errors")
Signed-off-by: NBenjamin Berg <bberg@redhat.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The IBS timers are not stopped properly once BT OFF is triggered.
we could see IBS commands being sent along with version command,
so stopped IBS timers while Bluetooth is off.

Fixes: 3e4be65e ("Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990")
Signed-off-by: NPanicker Harish <quic_pharish@quicinc.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add 2 USB IDs for MT7922A chip.
These 2 devices got the same description.

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0d8 Rev= 1.00

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0d9 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: NAaron Ma <aaron.ma@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch add missing HCI quirks and MSFT extension for legacy
bootloader when it is running in the operational firmware.
Signed-off-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add USB IDs (0x10ab, 0x9309) and (0x10ab, 0x9409) to
usb_device_id table for WCN6855.

* /sys/kernel/debug/usb/devices
T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 10 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=10ab ProdID=9309 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  65 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  65 Ivl=1ms

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 11 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=10ab ProdID=9409 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  65 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  65 Ivl=1ms
Signed-off-by: NZijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>

If user has a set to use SOCK_STREAM the socket would default to
L2CAP_MODE_ERTM which later needs to be adjusted if the destination
address is LE which doesn't support such mode.

Fixes: 15f02b91 ("Bluetooth: L2CAP: Add initial code for Enhanced Credit Based Mode")
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

hci_pause_advertising_sync shall always pause advertising until
hci_resume_advertising_sync but instance 0x00 doesn't count
in adv_instance_cnt so it was causing it to be skipped.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This makes use of mgmt_alloc_skb to build MGMT_EV_DEVICE_CONNECTED so
the data is copied directly to skb that is then sent using
mgmt_send_event_skb eliminating the necessity of intermediary buffers.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This makes use of mgmt_alloc_skb to build MGMT_EV_DEVICE_FOUND so the
data is copied directly to skb that is then sent using
mgmt_send_event_skb eliminating the necessity of intermediary buffers.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This introduces mgmt_alloc_skb and mgmt_send_event_skb which are
convenient when building MGMT events that have variable length as the
likes of skb_put_data can be used to insert portion directly on the skb
instead of having to first build an intermediate buffer just to be
copied over the skb.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If there are failure cases in getting patch status, it should return the
error code (-EIO).

Fixes: fc342c4d ("Bluetooth: btusb: Add protocol support for MediaTek MT7921U USB devices")
Co-developed-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

For Mediatek chipset, it can not enabled if there are something wrong
in btmtk_setup_firmware_79xx(). Thus, the process must be terminated
and returned error code.

Fixes: fc342c4d ("Bluetooth: btusb: Add protocol support for MediaTek MT7921U USB devices")
Co-developed-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This fixes compilation when CONFIG_BT_MSFTEXT is not set.

Fixes: 6b3d4c8fcf3f2 ("Bluetooth: hci_event: Use of a function table to handle HCI events")
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This adds support for Set Privacy Mode when updating the resolving list
when HCI_CONN_FLAG_DEVICE_PRIVACY so the controller shall use Device
Mode for devices programmed in the resolving list, Device Mode is
actually required when the remote device are not able to use RPA as
otherwise the default mode is Network Privacy Mode in which only
allows RPAs thus the controller would filter out advertisement using
identity addresses for which there is an IRK.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This introduces HCI_CONN_FLAG_DEVICE_PRIVACY which can be used by
userspace to indicate to the controller to use Device Privacy Mode to a
specific device.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This makes btusb to queue ACL and events during a polling interval
by using of a delayed work, with the interval working as a time window
where frames received from different endpoints are considered to be
arrived at same time and then attempt to resolve potential conflics by
processing the events ahead of ACL packets.

It worth noting though that priorizing events over ACL data may result
in inverting the order compared to how they appeared over the air, for
instance there may be packets received before a disconnect event that
will be discarded and unencrypted packets received before encryption
change which would considered encrypted, because of these potential
changes on the order the support for queuing during the polling
interval is not enabled by default so it requires setting
force_poll_sync debugfs while the adapter is down.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This reworks hci_conn_params flags to use bitmap_* helpers and add
support for setting the supported flags in hdev->conn_flags so it can
easily be accessed.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This make use of hci_dev_test_and_{set,clear}_flag instead of doing 2
operations in a row.

Fixes: cbbdfa6f ("Bluetooth: Enable controller RPA resolution using Experimental feature")
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Some Macs with the T2 security chip had Bluetooth not working.
To fix it we add DMI based quirks to disable querying of LE Tx power.
Signed-off-by: NAditya Garg <gargaditya08@live.com>
Reported-by: NOrlando Chamberlain <redecorating@protonmail.com>
Tested-by: NOrlando Chamberlain <redecorating@protonmail.com>
Link:
https://lore.kernel.org/r/4970a940-211b-25d6-edab-21a815313954@protonmail.com
Fixes: 7c395ea5 ("Bluetooth: Query LE tx power on startup")
Cc: stable@vger.kernel.org
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Some devices have a bug causing them to not work if they query
LE tx power on startup. Thus we add a quirk in order to not query it
and default min/max tx power values to HCI_TX_POWER_INVALID.
Signed-off-by: NAditya Garg <gargaditya08@live.com>
Reported-by: NOrlando Chamberlain <redecorating@protonmail.com>
Tested-by: NOrlando Chamberlain <redecorating@protonmail.com>
Link:
https://lore.kernel.org/r/4970a940-211b-25d6-edab-21a815313954@protonmail.com
Fixes: 7c395ea5 ("Bluetooth: Query LE tx power on startup")
Cc: stable@vger.kernel.org
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Similar to MT7921 btusb, we enable AOSP extension for MT7921 btmtksdio
as well.
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Enable msft opcode for mt7921 chip.
Signed-off-by: NŁukasz Bartosik <lb@semihalf.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add a USB ID 0489:e0e3 of HP to usb_device_id table for WCN6855.

-Device(0489:e0e3) from /sys/kernel/debug/usb/devices
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0e3 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:  If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  65 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  65 Ivl=1ms
Signed-off-by: NZijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change the use of switch statement to a function table which is
easier to extend.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change the use of switch statement to a function table which is
easier to extend and can include min/max length of each command.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change the use of switch statement to a function table which is
easier to extend and can include min/max length of each subevent.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This change the use of switch statement to a function table
which is easier to extend and can include min/max length of each HCI
event.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the LE Direct Advertising Report
events received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the LE Extended Advertising Report
events received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the LE Advertising Report events
received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the LE Metaevents received have the
minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the Extended Inquiry Result events
received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the Inquiry Result with RSSI events
received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the Inquiry Result events received
have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the Number of Complete Packets events
received have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the Command Complete events received
have the minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This uses skb_pull_data to check the BR/EDR events received have the
minimum required length.
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Like skb_pull but returns the original data pointer before pulling the
data after performing a check against sbk->len.

This allows to change code that does "struct foo *p = (void *)skb->data;"
which is hard to audit and error prone, to:

        p = skb_pull_data(skb, sizeof(*p));
        if (!p)
                return;

Which is both safer and cleaner.
Acked-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NLuiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>