Kernel log messages for failed AP reset commands should be suppressed.
These are expected to fail on devices that do not have an AP.  Add
missing driver reload message after AP reset and log it in a common
way without duplication.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ethtool ABI specifies that the reset operation should only clear
the flags that were actually reset. Setting the flags to zero after
a chip reset violates this because it does not include resetting the
application processor complex. Similarly, components that are not yet
defined are also not necessarily being reset.

The fact that chip reset does not cover the AP also means that it is
inappropriate to treat these two components exclusively of one another.
The ABI provides a mechanism to report a failure to reset independent
components via the returned bitmask, so it is also wrong to fail hard
if one of a set of independent resets is not possible.

It is incorrect to rely on the passed by reference flags in bnxt_reset(),
which are being updated as components are reset. The initially requested
value should be used instead so that hard errors do not propagate if any
earlier components could have been reset successfully.

Note, AP and chip resets are global in nature. Dedicated resets are
thus not currently supported.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The case statement in bnxt_firmware_reset() dangerously mixes types.
This patch separates the application processor and whole chip resets
from the rest such that the selection is performed on a pure type.
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract bnxt_hwrm_firmware_reset() for performing firmware reset
operations. This new helper function will be used in a subsequent
patch to separate unrelated reset types out of bnxt_firmware_reset().
Signed-off-by: NEdwin Peer <edwin.peer@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware does not expect the CRC to be included in the length
passed from the driver.  The firmware always configures the chip
to strip out the CRC.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current formulas to calculate the TQM slow path and fast path ring
context memory sizes are not quite correct.  TQM slow path entry is
array index 0 of ctx->tqm_mem[].  The other array entries are for fast
path.  Fix these sizes according to latest firmware spec. for 57500 and
newer chips.

Fixes: 3be8136c ("bnxt_en: Initialize context memory to the value specified by firmware.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Newer firmware spec. will specify the number of TQM rings to allocate
context memory for.  Use the firmware specified value and fall back
to the old value derived from bp->max_q if it is not available.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changes include additional statistics, ECN support, context memory
interface change for better TQM context memory sizing, firmware
health status definitions, etc.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Karsten Graul says:

====================
net/smc: add and delete link processing

These patches add the 'add link' and 'delete link' processing as
SMC server and client. This processing allows to establish and
remove links of a link group dynamically.

v2: Fix mess up with unused static functions. Merge patch 8 into patch 4.
    Postpone patch 13 to next series.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As SMC server, when a second link was deleted, trigger the setup of an
asymmetric link. Do this by enqueueing a local ADD_LINK message which
is processed by the LLC layer as if it were received from peer. Do the
same when a new IB port became active and a new link could be created.
smc_llc_srv_add_link_local() enqueues a local ADD_LINK message.
And smc_llc_srv_delete_link_local() is used the same way to enqueue a
local DELETE_LINK message. This is used when an IB port is no longer
active.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add smc_llc_process_srv_delete_link() to process a DELETE_LINK request
as SMC server. When the request is to delete ALL links then terminate
the whole link group. If not, find the link to delete by its link_id,
send the DELETE_LINK request LLC message and wait for the response.
No matter if a response was received, clear the deleted link and update
the link group state.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add smc_llc_process_cli_delete_link() to process a DELETE_LINK request
as SMC client. When the request is to delete ALL links then terminate
the whole link group. If not, find the link to delete by its link_id,
send the DELETE_LINK response LLC message and then clear the deleted
link. Finally determine and update the link group state.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a work that is scheduled when a new DELETE_LINK LLC request is
received. The work will call either the SMC client or SMC server
DELETE_LINK processing.
And use the LLC flow framework to process incoming DELETE_LINK LLC
messages, scheduling the llc_del_link_work for those events.
With these changes smc_lgr_forget() is only called by one function and
can be migrated into smc_lgr_cleanup_early().
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a link group moved from asymmetric to symmetric state then the
dangling asymmetric link can be deleted. Add smc_llc_find_asym_link() to
find the respective link and add smc_llc_delete_asym_link() to delete
it.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch finalizes the ADD_LINK processing of new links. Send the
CONFIRM_LINK request to the peer, receive the response and set link
state to ACTIVE.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Part of SMC server new link establishment is the exchange of rkeys for
used buffers.
Loop over all used RMB buffers and send ADD_LINK_CONTINUE LLC messages
to the peer.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

First set of functions to process an ADD_LINK LLC request as an SMC
server. Find an alternate IB device, determine the new link group type
and get the index for the new link. Then initialize the link and send
the ADD_LINK LLC message to the peer. Save the contents of the response,
ready the link, map all used buffers and register the buffers with the
IB device. If any error occurs, stop the processing and clear the link.
And call smc_llc_srv_add_link() in af_smc.c to start second link
establishment after the initial link of a link group was created.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch finalizes the ADD_LINK processing of new links. Receive the
CONFIRM_LINK request from peer, complete the link initialization,
register all used buffers with the IB device and finally send the
CONFIRM_LINK response, which completes the ADD_LINK processing.
And activate smc_llc_cli_add_link() in af_smc.c.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Part of the SMC client new link establishment process is the exchange of
rkeys for all used buffers.
Add new LLC message type ADD_LINK_CONTINUE which is used to exchange
rkeys of all current RMB buffers. Add functions to iterate over all
used RMB buffers of the link group, and implement the ADD_LINK_CONTINUE
processing.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

First set of functions to process an ADD_LINK LLC request as an SMC
client. Find an alternate IB device, determine the new link group type
and get the index for the new link. Then ready the link, map the buffers
and send an ADD_LINK LLC response. If any error occurs, send a reject
LLC message and terminate the processing.
Add smc_llc_alloc_alt_link() to find a free link index for a new link,
depending on the new link group type.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Reviewed-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sameeh Jubran says:

====================
Enhance current features in ena driver

Difference from v2:
* dropped patch "net: ena: move llq configuration from ena_probe to ena_device_init()"
* reworked patch ""net: ena: implement ena_com_get_admin_polling_mode() to drop the prototype

Difference from v1:
* reodered paches #01 and #02.
* dropped adding Rx/Tx drops to ethtool in patch #08

V1:
This patchset introduces the following:
* minor changes to RSS feature
* add total rx and tx drop counter
* add unmask_interrupt counter for ethtool statistics
* add missing implementation for ena_com_get_admin_polling_mode()
* some minor code clean-up and cosmetics
* use SHUTDOWN as reset reason when closing interface
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract code to ena_indirection_table_set() to make
the code cleaner.
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macros in ena_com.h have inconsistent spaces between
the macro name and it's value.

This commit sets all the macros to have a single space between
the name and value.
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 'ENA_REGS_RESET_SHUTDOWN' enum indicates a normal driver
shutdown / removal procedure.

Also, a comment is added to one of the reset reason assignments for
code clarity.
Signed-off-by: NShay Agroskin <shayagr@amazon.com>
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before this commit there was a function prototype named
ena_com_get_ena_admin_polling_mode() that was never implemented.

This patch simply deletes it.
Signed-off-by: NIgor Chauskin <igorch@amazon.com>
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Add support for getting tx drops from the device and saving them
in the driver.
2. Report tx via netdev stats.
Signed-off-by: NIgor Chauskin <igorch@amazon.com>
Signed-off-by: NGuy Tzalik <gtzalik@amazon.com>
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add unmask interrupts statistics to ethtool.
Signed-off-by: NNetanel Belgazal <netanel@amazon.com>
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both key and func parameters are pointers on the stack.
Setting them to NULL does nothing.
The original intent was to leave the key and func unset in this case,
but for this to happen nothing needs to be done as the calling
function ethtool_get_rxfh() already clears key and func.

This commit removes the above described useless code.
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit contains 2 cosmetic changes:

1. Use ena_com_check_supported_feature_id() in
   ena_com_hash_key_fill_default_key() instead of rewriting
   its implementation. This also saves us a superfluous admin
   command by using the cached value.

2. Change if conditions in ena_com_rss_init() to be clearer.
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently in the driver we are setting the hash function to be CRC32.
Starting with this commit we want to change the default behaviour so that
we set the hash function to be Toeplitz instead.
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current code does not allow setting the hash function without
changing the key. This commit enables it.

To achieve this we separate ena_com_get_hash_function() to 2 functions:
ena_com_get_hash_function() - which gets only the hash function, and
ena_com_get_hash_key() - which gets only the hash key.

Also return 0 instead of rc at the end of ena_get_rxfh() since all
previous operations succeeded.
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case the "func" parameter is NULL we now return "-EINVAL".
This shouldn't happen in general, but when it does happen, this is the
proper way to handle it.

We also check func for NULL in the beginning of the function, as there
is no reason to do all the work and realize in the end of the function
it was useless.
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently when ena_set_hash_function() fails the hash function is
restored to the previous value by calling an admin command to get
the hash function from the device.

In this commit we avoid the admin command, by saving the previous
hash function before calling ena_set_hash_function() and using this
previous value to restore the hash function in case of failure of
ena_set_hash_function().
Signed-off-by: NSameeh Jubran <sameehj@amazon.com>
Signed-off-by: NArthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net_sched: sch_fq: round of optimizations

This series is focused on better layout of struct fq_flow to
reduce number of cache line misses in fq_enqueue() and dequeue operations.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The prefetch() done in fq_dequeue() can be done a bit earlier
after the refactoring of the code done in the prior patch.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This refactors the code to not call fq_peek() from fq_dequeue_head()
since the caller can provide the skb.

Also rename fq_dequeue_head() to fq_dequeue_skb() because 'head' is
a bit vague, given the skb could come from t_root rb-tree.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fq_gc() already builds a small array of pointers, so using
kmem_cache_free_bulk() needs very little change.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sizeof(struct fq_flow) is 112 bytes on 64bit arches.

This means that half of them use two cache lines, but 50% use
three cache lines.

This patch adds cache line alignment, and makes sure that only
the first cache line is touched by fq_enqueue(), which is more
expensive that fq_dequeue() in general.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A significant amount of cpu cycles is spent in fq_gc()

When fq_gc() does its lookup in the rb-tree, it needs the
following fields from struct fq_flow :

f->sk       (lookup key in the rb-tree)
f->fq_node  (anchor in the rb-tree)
f->next     (used to determine if the flow is detached)
f->age      (used to determine if the flow is candidate for gc)

This unfortunately spans two cache lines (assuming 64 bytes cache lines)

We can avoid using f->next, if we use the low order bit of f->{age|tail}

This low order bit is 0, if f->tail points to an sk_buff.
We set the low order bit to 1, if the union contains a jiffies value.

Combined with the following patch, this makes sure we only need
to bring into cpu caches one cache line per flow.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix bug introduced by commit b1f3e43d ("inet_diag: add support for
cgroup filter").
Signed-off-by: NDmitry Yakunin <zeil@yandex-team.ru>
Reported-by: syzbot+ee80f840d9bf6893223b@syzkaller.appspotmail.com
Reported-by: syzbot+13bef047dbfffa5cd1af@syzkaller.appspotmail.com
Fixes: b1f3e43d ("inet_diag: add support for cgroup filter")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>