Move e_clkput label after the clk_disable() call so a not acquired clock
is not attempted to be disabled. This fixes runtime warnings like:
 s5p-mipi-csis 11880000.csis: failed to get clock: sclk_csis
 ------------[ cut here ]------------
 WARNING: at drivers/clk/clk.c:478 clk_disable+0x24/0x34()
 Modules linked in:
 [<c001603c>] (unwind_backtrace+0x0/0x13c) from [<c0022060>] (warn_slowpath_common+0x54/0x64)
 [<c0022060>] (warn_slowpath_common+0x54/0x64) from [<c002208c>] (warn_slowpath_null+0x1c/0x24)
 [<c002208c>] (warn_slowpath_null+0x1c/0x24) from [<c033f868>] (clk_disable+0x24/0x34)
 [<c033f868>] (clk_disable+0x24/0x34) from [<c02feff8>] (s5pcsis_probe+0x25c/0x4c8)
 [<c02feff8>] (s5pcsis_probe+0x25c/0x4c8) from [<c0268e34>] (platform_drv_probe+0x18/0x1c)
 [<c0268e34>] (platform_drv_probe+0x18/0x1c) from [<c0267700>] (driver_probe_device+0xa4/0x368)
 [<c0267700>] (driver_probe_device+0xa4/0x368) from [<c0267a50>] (__driver_attach+0x8c/0x90)
 [<c0267a50>] (__driver_attach+0x8c/0x90) from [<c0265c94>] (bus_for_each_dev+0x60/0x8c)
 [<c0265c94>] (bus_for_each_dev+0x60/0x8c) from [<c02665e8>] (bus_add_driver+0x20c/0x2d4)
 [<c02665e8>] (bus_add_driver+0x20c/0x2d4) from [<c0268064>] (driver_register+0x78/0x194)
 [<c0268064>] (driver_register+0x78/0x194) from [<c0008668>] (do_one_initcall+0x34/0x188)
 [<c0008668>] (do_one_initcall+0x34/0x188) from [<c03de57c>] (kernel_init+0x180/0x2f0)
 [<c03de57c>] (kernel_init+0x180/0x2f0) from [<c000f0d8>] (ret_from_fork+0x14/0x3c)
 ---[ end trace 0c5a55345c42530b ]---
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

clk_set_rate(), clk_enable() functions can fail, so check the return
values to avoid surprises. While at it use ERR_PTR() value to indicate
an invalid clock.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

devm_regulator_bulk_get is device managed and saves some cleanup
and exit code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

CONFIG_HOTPLUG is going away as an option.  As a result, the __dev*
markings need to be removed.

This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.

Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.

Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

spinlock_t should always be used.
Could not get this to build with allmodconfig:
mcgrof@frijol ~/linux-next (git::(no branch))$ make C=1 M=drivers/media/platform/s5p-fimc/
  WARNING: Symbol version dump /home/mcgrof/linux-next/Module.symvers
           is missing; modules will have no dependencies and modversions.
  LD      drivers/media/platform/s5p-fimc/built-in.o
  Building modules, stage 2.
  MODPOST 0 modules
Reported-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NLuis R. Rodriguez <mcgrof@do-not-panic.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Dump registers contents together with the event counters state
in VIDIOC_LOG_STATUS ioctl.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Enable only MIPI CSI-2 data lanes at the DPHY that are actively
used, rather than unmasking all unconditionally.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The MIPI CSIS device supports MIPI CSI-2 RAW8, RAW10, RAW12 data
types. Add related media bus pixel format definitions. This
doesn't cover all possible supported media bus pixel formats.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The counter field is unsigned so >= 0 condition always evaluates
to true. Fix this to log events for which counter is > 0 or for
all when in debug mode.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Depending on the sensor configuration it might be required to adjust
the CSIS's output pixel clock so it is greater than its input pixel
clock, in order to avoid the input data FIFO overflow.
Use platform data to select SCLK_CSIS clock from CMU as a source, rather
than CSI APB clock.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The phy_enable callback is common for all Samsung SoC platforms,
replace it with direct function call so the MIPI-CSI2 DPHY control
is also possible on device tree instantiated platforms.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Rename the regulator supply names to more meaningful ones.
It's a prerequisite for adding device tree support.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The V4L2_PIX_FMT_S5C_YUYV_JPG image formats consists of 2 planes, the
first containing interleaved JPEG/YUYV data and the second containing
meta data describing the interleaving method.
The image data is transferred with MIPI-CSI "User Defined Byte-Based
Data 1" type and is captured to memory by FIMC DMA engine.
The meta data is transferred using MIPI-CSI2 "Embedded 8-bit non Image
Data" and it is captured in the MIPI-CSI slave device and copied to
the bridge provided buffer.
To make sure the size of allocated buffers is correct for the subdevs
configuration when VIDIOC_STREAMON ioctl is invoked, an additional
check is added at the video pipeline validation function.
Flag FMT_FLAGS_COMPRESSED indicates the buffer size must be retrieved
from a sensor subdev.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

MIPI-CSI has internal memory mapped buffers for the frame embedded
(non-image) data. There are two buffers, for even and odd frames which
need to be saved after an interrupt is raised. The packet data buffers
size is 4 KiB and there is no status register in the hardware where the
actual non-image data size can be read from. Hence the driver copies
whole packet data buffer into a buffer provided by the FIMC driver.
This will form a separate plane in the user buffer.
When FIMC DMA engine is stopped by the driver due the to user space
not keeping up with buffer de-queuing the MIPI-CSIS will still run,
however it must discard data which is not captured by FIMC. Which
frames are actually capture by MIPI-CSIS is determined by means of
the s_tx_buffer subdev callback. When it is not called after a single
embedded data frame has been captured and copied and before next
embedded data frame interrupt occurrs, subsequent embedded data frames
will be dropped.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add hardware event/error counters which can be dumped into the kernel
log through VIDIOC_LOG_STATUS ioctl. The counters are reset  in each
s_stream(1) call. Any errors are logged after streaming is turned off.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The remaining drivers are mostly platform drivers. Name the
dir to reflect it.

It makes sense to latter break it into a few other dirs.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In this driver there are several entities associated with separate
platform or I2C client devices, which may get probed in random order.

When the platform device bound to the media device driver is probed
all other entity drivers need to be already in place and initialized.
If any of them is not, fail the media device probe and return an error
indicating we need to be retried once any new driver gets registered.
The media device driver probe will not succeed until there are available
all needed sub-drivers, as specified in the platform data.

While at it, make sure the s5p-csis module (MIPI-CSI receiver driver)
does not get unloaded when in use, by guarding its usage with
try_module_get/module_put.

This patch is a prerequisite for adding the device tree support.
It now also allows again to unbind/bind the driver at runtime from
user space via sysfs.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The MIPI-CSI2 data alignment parameter can be derived from media bus
pixel code, so it can be now dropped from the platform data structure.
This is a prerequisite for adding the device tree support. Once this
patch is merged the corresponding fields will be removed from the
drivers' public headers and corresponding board files.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix following compilation error when CONFIG_PM_SLEEP is disabled:

  CC      drivers/media/video/s5p-fimc/mipi-csis.o
drivers/media/video/s5p-fimc/mipi-csis.c: In function ‘s5pcsis_remove’:
drivers/media/video/s5p-fimc/mipi-csis.c:956: error: implicit declaration of function ‘s5pcsis_suspend’
Reported-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The devm_* functions are used in the platform device probe() for data
that is freed on driver removal. The managed device layer takes care
of undoing actions taken in the probe callback() and freeing resources
on driver detach. This eliminates the need for manually releasing
resources and simplifies error handling.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Set v4l2_subdev flags for a host driver to create a sub-device
node for the driver so the subdev can be directly configured
by applications. Add the subdev open() handler.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Do not resume the device during system resume if it was idle
before system suspend, as this causes resume from suspend
to RAM failures on Exynos4. For this purpose runtime PM and
system sleep helpers are separated.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On the SoCs this driver is intended to support the are three separate
pins to supply the MIPI-CSIS subsystem: 1.1V or 1.2V, 1.8V and power
supply for an internal PLL.
This patch adds support for two separate voltage supplies to cover
properly board configurations where PMIC requires to configure
independently each external supply of the MIPI-CSI device. The 1.8V
and PLL supply are assigned a single "vdd18" regulator supply name
as it seems more reasonable than creating separate regulator supplies
for them.

While at here stop using the 'fixed_phy_vdd' platform_data field.
It has been introduced for boards where the MIPI-CSIS supplies are
not controllable. However it is not needed as those boards can use
the dummy regulator.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the subdev driver for the MIPI CSIS units available in S5P and
Exynos4 SoC series. This driver supports both CSIS0 and CSIS1
MIPI-CSI2 receivers.
The driver requires Runtime PM to be enabled for proper operation.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>