Stateless decoders have different expectations about the
start code that is prepended on H264 slices. Add a
menu control to express the supported start code types
(including no start code).

Drivers are allowed to support only one start code type,
but they can support both too.

Note that this is independent of the H264 decoding mode,
which specifies the granularity of the decoding operations.
Either in frame-based or slice-based mode, this new control
will allow to define the start code expected on H264 slices.
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>
Tested-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Some stateless decoders don't support per-slice decoding granularity
(or at least not in a way that would make them efficient or easy to use).

Expose a menu to control the supported decoding modes. Drivers are
allowed to support only one decoding but they can support both too.

To fully specify the decoding operation, we need to introduce
a start_byte_offset, to indicate where slices start.
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: NPaul Kocialkowski <paul.kocialkowski@bootlin.com>
Tested-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The V4L2_PIX_FMT_H264_SLICE_RAW name was originally suggested
because the pixel format would represent H264 slices without any
start code.

However, as we will now introduce a start code menu control,
give the pixel format a more meaningful name, while it's
still early enough to do so.
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>
Tested-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

If reg_r() fails, then gspca_dev->usb_buf was left uninitialized,
and some drivers used the contents of that buffer in logic.

This caused several syzbot errors:

https://syzkaller.appspot.com/bug?extid=397fd082ce5143e2f67d
https://syzkaller.appspot.com/bug?extid=1a35278dd0ebfb3a038a
https://syzkaller.appspot.com/bug?extid=06ddf1788cfd048c5e82

I analyzed the gspca drivers and zeroed the buffer where needed.

Reported-and-tested-by: syzbot+1a35278dd0ebfb3a038a@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+397fd082ce5143e2f67d@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+06ddf1788cfd048c5e82@syzkaller.appspotmail.com
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

dev->usbc_buf was passed as argument for %s, but it was not safeguarded
by a terminating 0.

This caused this syzbot issue:

https://syzkaller.appspot.com/bug?extid=79d18aac4bf1770dd050

Reported-and-tested-by: syzbot+79d18aac4bf1770dd050@syzkaller.appspotmail.com
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

In the probe() function radio->int_in_urb was not killed if an
error occurred in the probe sequence. It was also missing in
the disconnect.

This caused this syzbot issue:

https://syzkaller.appspot.com/bug?extid=2d4fc2a0c45ad8da7e99

Reported-and-tested-by: syzbot+2d4fc2a0c45ad8da7e99@syzkaller.appspotmail.com
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add support of several sub-devices within pipeline instead
of a single one.
This allows to support a CSI-2 camera sensor connected
through a CSI-2 to parallel bridge.
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add media controller support to dcmi in order
to walk within remote subdevices pipeline.
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add a trace of the set of supported fourcc/mbus_code which
intersect between DCMI and source sub-device.
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Rename "subdev" entity struct field to "source"
to prepare for several subdev support.
Move asd field on top of entity struct.
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Fix typos.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Some users have been having a hard time finding the hidden
menus. A typically case are camera sensor drivers
(e.g IMX219, OV5645, etc), which are common on embedded
platforms and not really "ancillary" devices.

The problem with MEDIA_SUBDRV_AUTOSELECT seems to be related
to the fact that it uses the "visible" syntax to hide
the menus.

This is not obvious and it normally takes some time to
figure out.

To fix the problem, add a comment on each of hidden menus,
which should clarify what option is causing menus to be hidden.
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

i.MX7 and i.MX6UL/L have the same CSI controller. So add i.MX6UL/L support
to imx7-media-csi driver.
Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: NRui Miguel Silva <rmfrfs@gmail.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Not all sensors will be able to guarantee a proper initial state.
This may be either because the driver is not properly written,
or (probably unlikely) because the hardware won't support it.

While the right solution in the former case is to fix the sensor
driver, the real world not always allows right solutions, due to lack
of available documentation and support on these sensors.

Let's relax this requirement, and allow the driver to support stream start,
even if the sensor initial sequence wasn't the expected.

Also improve the warning message to better explain the problem and provide
a hint that the sensor driver needs to be fixed.
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NSteve Longerbeam <slongerbeam@gmail.com>
Reviewed-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

This is mostly a port of Jacopo's fix:

  commit aa4bb8b8
  Author: Jacopo Mondi <jacopo@jmondi.org>
  Date:   Fri Jul 6 05:51:52 2018 -0400

  media: ov5640: Re-work MIPI startup sequence

In the OV5645 case, the changes are:

- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
  LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current
  power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.

With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.

Many thanks to Fabio Estevam for his help debugging this issue.
Tested-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NEzequiel Garcia <ezequiel@collabora.com>
Reviewed-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: NJacopo Mondi <jacopo@jmondi.org>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The streaming state should be set to the first upstream sub-device only,
not everywhere, for a sub-device driver itself knows how to best control
the streaming state of its own upstream sub-devices.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The omap3isp driver registered subdevs without the dev field being set. Do
that now.
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: NLuca Weiss <luca@z3ntu.xyz>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Instead of blindly trusting getting the clock frequency succeeded end then
testing it against a pre-defined value, verify reading the value
succeeded.

Fixes: 879347f0 ("media: ov8856: Add support for OV8856 sensor")
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Add a V4L2 sub-device driver for Omnivision ov5675 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.

This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
  + 2592x1944 at 30FPS
  + 1296x972  at 30FPS

[Sakari Ailus: Wrapped a few long lines.]
[mchehab+samsung@kernel.org: fix a checkpatch warning]
Signed-off-by: NShawn Tu <shawnx.tu@intel.com>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Currently when the call vsp1_dl_body_get fails and returns null the
error return path leaks the allocation of dl. Fix this by kfree'ing
dl before returning.

Addresses-Coverity: ("Resource leak")

Fixes: 5d7936b8 ("media: vsp1: Convert display lists to use new body pool")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Allow selecting the IR protocol, MCE or iMON, for a device that
identifies as follows (with config id 0x7e):

15c2:ffdc SoundGraph Inc. iMON PAD Remote Controller

As the driver is structured to default to iMON when both RC
protocols are supported, existing users of this device (using MCE
protocol) will need to manually switch to MCE (RC-6) protocol from
userspace (with ir-keytable, sysfs).
Signed-off-by: NDarius Rad <alpha@area49.net>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The usb_bulk_urb will kfree'd on disconnect, so ensure the pointer is set
to NULL after each free.

stop stream
urb killing
urb buffer free
tm6000: got start feed request tm6000_start_feed
tm6000: got start stream request tm6000_start_stream
tm6000: pipe reset
tm6000: got start feed request tm6000_start_feed
tm6000: got start feed request tm6000_start_feed
tm6000: got start feed request tm6000_start_feed
tm6000: got start feed request tm6000_start_feed
tm6000: IR URB failure: status: -71, length 0
xhci_hcd 0000:00:14.0: ERROR unknown event type 37
xhci_hcd 0000:00:14.0: ERROR unknown event type 37
tm6000:  error tm6000_urb_received
usb 1-2: USB disconnect, device number 5
tm6000: disconnecting tm6000 #0
==================================================================
BUG: KASAN: use-after-free in dvb_fini+0x75/0x140 [tm6000_dvb]
Read of size 8 at addr ffff888241044060 by task kworker/2:0/22

CPU: 2 PID: 22 Comm: kworker/2:0 Tainted: G        W         5.3.0-rc4+ #1
Hardware name: LENOVO 20KHCTO1WW/20KHCTO1WW, BIOS N23ET65W (1.40 ) 07/02/2019
Workqueue: usb_hub_wq hub_event
Call Trace:
 dump_stack+0x9a/0xf0
 print_address_description.cold+0xae/0x34f
 __kasan_report.cold+0x75/0x93
 ? tm6000_fillbuf+0x390/0x3c0 [tm6000_alsa]
 ? dvb_fini+0x75/0x140 [tm6000_dvb]
 kasan_report+0xe/0x12
 dvb_fini+0x75/0x140 [tm6000_dvb]
 tm6000_close_extension+0x51/0x80 [tm6000]
 tm6000_usb_disconnect.cold+0xd4/0x105 [tm6000]
 usb_unbind_interface+0xe4/0x390
 device_release_driver_internal+0x121/0x250
 bus_remove_device+0x197/0x260
 device_del+0x268/0x550
 ? __device_links_no_driver+0xd0/0xd0
 ? usb_remove_ep_devs+0x30/0x3b
 usb_disable_device+0x122/0x400
 usb_disconnect+0x153/0x430
 hub_event+0x800/0x1e40
 ? trace_hardirqs_on_thunk+0x1a/0x20
 ? hub_port_debounce+0x1f0/0x1f0
 ? retint_kernel+0x10/0x10
 ? lock_is_held_type+0xf1/0x130
 ? hub_port_debounce+0x1f0/0x1f0
 ? process_one_work+0x4ae/0xa00
 process_one_work+0x4ba/0xa00
 ? pwq_dec_nr_in_flight+0x160/0x160
 ? do_raw_spin_lock+0x10a/0x1d0
 worker_thread+0x7a/0x5c0
 ? process_one_work+0xa00/0xa00
 kthread+0x1d5/0x200
 ? kthread_create_worker_on_cpu+0xd0/0xd0
 ret_from_fork+0x3a/0x50

Allocated by task 2682:
 save_stack+0x1b/0x80
 __kasan_kmalloc.constprop.0+0xc2/0xd0
 usb_alloc_urb+0x28/0x60
 tm6000_start_feed+0x10a/0x300 [tm6000_dvb]
 dmx_ts_feed_start_filtering+0x86/0x120 [dvb_core]
 dvb_dmxdev_start_feed+0x121/0x180 [dvb_core]
 dvb_dmxdev_filter_start+0xcb/0x540 [dvb_core]
 dvb_demux_do_ioctl+0x7ed/0x890 [dvb_core]
 dvb_usercopy+0x97/0x1f0 [dvb_core]
 dvb_demux_ioctl+0x11/0x20 [dvb_core]
 do_vfs_ioctl+0x5d8/0x9d0
 ksys_ioctl+0x5e/0x90
 __x64_sys_ioctl+0x3d/0x50
 do_syscall_64+0x74/0xe0
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 22:
 save_stack+0x1b/0x80
 __kasan_slab_free+0x12c/0x170
 kfree+0xfd/0x3a0
 xhci_giveback_urb_in_irq+0xfe/0x230
 xhci_td_cleanup+0x276/0x340
 xhci_irq+0x1129/0x3720
 __handle_irq_event_percpu+0x6e/0x420
 handle_irq_event_percpu+0x6f/0x100
 handle_irq_event+0x55/0x84
 handle_edge_irq+0x108/0x3b0
 handle_irq+0x2e/0x40
 do_IRQ+0x83/0x1a0

Cc: stable@vger.kernel.org
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

KEY_MAX is not a key but designates the highest value a linux keycode
can ever have.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

syzbot reports an error on flush_request_modules() for the second device.
This workqueue was never initialised so simply remove the offending line.

usb 1-1: USB disconnect, device number 2
em28xx 1-1:1.153: Disconnecting em28xx #1
------------[ cut here ]------------
WARNING: CPU: 0 PID: 12 at kernel/workqueue.c:3031
__flush_work.cold+0x2c/0x36 kernel/workqueue.c:3031
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.3.0-rc2+ #25
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0xca/0x13e lib/dump_stack.c:113
  panic+0x2a3/0x6da kernel/panic.c:219
  __warn.cold+0x20/0x4a kernel/panic.c:576
  report_bug+0x262/0x2a0 lib/bug.c:186
  fixup_bug arch/x86/kernel/traps.c:179 [inline]
  fixup_bug arch/x86/kernel/traps.c:174 [inline]
  do_error_trap+0x12b/0x1e0 arch/x86/kernel/traps.c:272
  do_invalid_op+0x32/0x40 arch/x86/kernel/traps.c:291
  invalid_op+0x23/0x30 arch/x86/entry/entry_64.S:1026
RIP: 0010:__flush_work.cold+0x2c/0x36 kernel/workqueue.c:3031
Code: 9a 22 00 48 c7 c7 20 e4 c5 85 e8 d9 3a 0d 00 0f 0b 45 31 e4 e9 98 86
ff ff e8 51 9a 22 00 48 c7 c7 20 e4 c5 85 e8 be 3a 0d 00 <0f> 0b 45 31 e4
e9 7d 86 ff ff e8 36 9a 22 00 48 c7 c7 20 e4 c5 85
RSP: 0018:ffff8881da20f720 EFLAGS: 00010286
RAX: 0000000000000024 RBX: dffffc0000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff8128a0fd RDI: ffffed103b441ed6
RBP: ffff8881da20f888 R08: 0000000000000024 R09: fffffbfff11acd9a
R10: fffffbfff11acd99 R11: ffffffff88d66ccf R12: 0000000000000000
R13: 0000000000000001 R14: ffff8881c6685df8 R15: ffff8881d2a85b78
  flush_request_modules drivers/media/usb/em28xx/em28xx-cards.c:3325 [inline]
  em28xx_usb_disconnect.cold+0x280/0x2a6
drivers/media/usb/em28xx/em28xx-cards.c:4023
  usb_unbind_interface+0x1bd/0x8a0 drivers/usb/core/driver.c:423
  __device_release_driver drivers/base/dd.c:1120 [inline]
  device_release_driver_internal+0x404/0x4c0 drivers/base/dd.c:1151
  bus_remove_device+0x2dc/0x4a0 drivers/base/bus.c:556
  device_del+0x420/0xb10 drivers/base/core.c:2288
  usb_disable_device+0x211/0x690 drivers/usb/core/message.c:1237
  usb_disconnect+0x284/0x8d0 drivers/usb/core/hub.c:2199
  hub_port_connect drivers/usb/core/hub.c:4949 [inline]
  hub_port_connect_change drivers/usb/core/hub.c:5213 [inline]
  port_event drivers/usb/core/hub.c:5359 [inline]
  hub_event+0x1454/0x3640 drivers/usb/core/hub.c:5441
  process_one_work+0x92b/0x1530 kernel/workqueue.c:2269
  process_scheduled_works kernel/workqueue.c:2331 [inline]
  worker_thread+0x7ab/0xe20 kernel/workqueue.c:2417
  kthread+0x318/0x420 kernel/kthread.c:255
  ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352
Kernel Offset: disabled
Rebooting in 86400 seconds..

Fixes: be7fd3c3 ("media: em28xx: Hauppauge DualHD second tuner functionality)
Reviewed-by: NEzequiel Garcia <ezequiel@collabora.com>
Reviewed-by: NBrad Love <brad@nextdimension.cc>
Reported-by: syzbot+b7f57261c521087d89bb@syzkaller.appspotmail.com
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Sometimes the device sends IR data which is all space, no pulses
whatsoever. Add the end of this the driver will put the rc device into
idle mode when it already is in idle mode. The following will be logged:

rc rc0: nonsensical timing event of duration 0
rc rc0: two consecutive events of type space
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

This code needs some explanation.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

Convert this driver to use the new i2c_new_dummy_device() call and bail
out if the dummy device cannot be registered to make failure more
visible to the user.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The variables mclk, div and ad_div are being assigned with a values
that are never read and are being updated later with a new values.
The assignments are redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: NFuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: NFuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: NFuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

In commit 518a2f19
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed
Signed-off-by: NFuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f19
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: NFuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd ("i2c: Provide a temporary .probe_new() call-back type").

These drivers do not utilise the i2c_device_id table in the probe, so we
can easily convert them to utilise the simplified i2c driver
registration.
Signed-off-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd ("i2c: Provide a temporary .probe_new() call-back type").

This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.
Signed-off-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd ("i2c: Provide a temporary .probe_new() call-back type").

This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.
Signed-off-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd ("i2c: Provide a temporary .probe_new() call-back type").

This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.
Signed-off-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd ("i2c: Provide a temporary .probe_new() call-back type").

This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.
Signed-off-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>

The I2C core framework provides a simplified probe framework from commit
b8a1a4cd ("i2c: Provide a temporary .probe_new() call-back type").

This driver does not utilise the i2c_device_id table in the probe, so we can
easily convert it to utilise the simplified i2c driver registration.
Signed-off-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>