Firmware will support filtering multicast L3 packets.
The L3 filtering is configured by the WOWLAN_CONFIG command.
All flags should be enabled by default.
Older firmware is not affected as it does not look into
this field.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of keeping the fw_key_table bits set when the keys are removed
(i.e. in D3 entry or HW_RESTART flows), clear them and set them again
only when the keys have been successfully re-added.  This makes the
bitmask more closely tied to the actual firmware programming.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

RFC4862 states that "In all cases, a node MUST NOT respond to
a Neighbor Solicitation for a tentative address".
Currently the driver configures the NS offload and does not wait
for address to become permanent, thus violating the RFC.
Just removing the address from the address list is not good enough
for all cases, since the NS messages are needed for the duplicate
address detection and should not be discarded.

For d0i3 disable NS offload. Put tentative address in the address
list so the NS packet will not be filtered out by ucode.
For D3 the platform will not wake from NS packets - so enable
NS offload while removing the tentative address from the list.

Given that now NS offload might be disabled, and that the ucode
uses the IP data for other puroposes (L3 filtering) add two
independent flags indicating if IPv4\IPv6 data is valid.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The d0i3_mode variable is used to distinguish between transports that
handle d0i3 entry during suspend by themselves (i.e. the slave
transports) and those which rely on the op_mode layer to do it.  The
reason why the former do it by themselves is that they need to
transition from d0i3 in runtime_suspend into d0i3 in system-wide
suspend and this transition needs to happen before the op_mode's
suspend flow is called.

The wowlan_d0i3 element is also a bit confusing, because it just
reflects the wowlan->any value for the trans to understand.  This is a
bit unclear in the code and not generic enough for future use.

To make it clearer and to generalize the platform power mode settings,
introduce two variables to indicate the platform power management
modes used by the transport.

Additionally, in order not to take too big a step in one patch, treat
this new variables semantically in the same way as the old d0i3_mode
element, introducing a iwl_mvm_enter_d0i3_on_suspend() function to
help with that.

This commit also adds the foundation for a new concept where the
firmware configuration state (i.e. D0, D3 or D0i3) is abstracted from
the platform PM mode we are in (i.e. runtime suspend or system-wide
suspend).
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

commit 9a4c830007817e ("iwlwifi: mvm: refactor d3 key
update functions") refactored some code into
iwl_mvm_wowlan_config_key_params() function, but the
return value was never checked, and not all the function
flows returned valid values. fix it.

Fixes: ac8ef0ce ("iwlwifi: mvm: refactor d3 key update functions")
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the wifi wakes up the system, we need to report it via calling
pm_wakeup_event for lucid sleep. This is so userspace knowns that the
wifi woke up the system via the /sys/power/wakeup_type sysfs interface.
Signed-off-by: NDerek Basehore <dbasehore@chromium.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We need to reuse the key update logic for d0i3
as well.

Add some parameters to deal with the constraints
implied by the d0i3 flow (specifically, support
non-SYNC commands, and don't take mutexes that
might deadlock).

Change some commands to be ASYNC, in order
to simplify locking a bit.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the netdetect debugfs entry was removed, the nd_config element
was accidentally left in the iwl_mvm structure.  Remove it.

Fixes: dbb04b0d ("iwlwifi: mvm: remove netdetect debugfs entry")
Reported-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This function updates the pairwise keys as well.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When entering D3, we need to use hardcoded key indices because the
firmware requires that.  To do so, we are overwriting the HW key index
in the keyconf structure, which makes it impossible to reuse the
indices that were used before entering D3.  Additionally, we overwrite
all the non-PTK keys with index 1, because the firmware only allows
one non-PTK key to be set.  This is bad, because when we resume, we
may try to set more than one key with index 1, which will obviously
fail.

To fix this, allow the callers to set a pre-defined index to use in
iwl_mvm_set_sta_key() instead of relying on the hw_key_idx value from
the keyconf struct (which requires overwriting it).  In normal cases,
the caller can pass STA_KEY_IDX_INVALID, which will cause a new key
offset to be chosen.  During HW_RESTART, we pass the offset that is in
use.  And during D3 entry, we pass the hardcoded indices we need to
use.

Additionally, don't clear the fw_key_table in D3 entry, so that the
flags are still set with the pre-D3 values when exiting D3.

fixes=I3165c22362483f0152d9ec1d2a987fb5529727c1

Fixes: b546dcd6 ("iwlwifi: mvm: don't reset key index on HW restart")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The code to send the RX PN data (for each TID) to the firmware
has a devastating bug: it overwrites the data for TID 0 with
all the TID data, leaving the remaining TIDs zeroed. This will
allow replays to actually be accepted by the firmware, which
could allow waking up the system.

Cc: <stable@vger.kernel.org> [3.1+]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When going into/coming out of D3, the TX PN must be programmed into
and restored from the firmware respectively. The restore was broken
due to my previous commit to move PN assignment into the driver.
Sending the PN to the firmware still worked since we now use the
counter that's shared with mac80211, but accessing it through the
mac80211 API makes no sense now.

Fix this by reading/writing the counter directly. This actually
simplifies the code since we don't need to round-trip through the
key_seq structure.

Fixes: ca8c0f4b ("iwlwifi: mvm: move TX PN assignment for CCMP to the driver")
Cc: <stable@vger.kernel.org> [4.1+]
Reported-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If we are in d0i3 when entering suspend, we leave d0i3 so that
mac80211 can call us to remove connections or whatever before going to
suspend.  We do this by calling pm_runtime_resume() early in the slave
transport flow and reactivating it later, when the wiphy suspend flow
runs.

The problem is that we queue a work in order to leave d0i3.  If this
work hasn't run yet when the wiphy suspend flow is called, we have a
race and entering d0i3 fails (because we're still holding the
IWL_MVM_REF_EXIT_WORK reference).

To solve this, simply flush the d0i3_exit_work at the beginning of the
iwl_mvm_suspend() function.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

Add support for extended command id in notification system.
Extended command id header contains group id in addition to command id.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some CSR registers have to be configured also
in case of suspend/resume with unified image
(which doesn't includes reconfiguration flow).

Reuse the existing d3_suspend/d3_resume trans ops,
while making sure some configurations are a bit
different, according to the wowlan type.

After this change, we no longer need the special
wowlan_d0i3 configurations done in iwl_pci_resume,
as they are already being done in the d3_resume op.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow the transport layer to return an error upon suspend.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This reverts commit 088070a2.

When working in d0i3_on_idle mode, we explicitly go out
of d0i3 on resume (so other potential commands could
be sent).

However, D0I3_DEFER_WAKEUP is currently cleared on
resume complete (which happens only later on), causing
d0i3 exit to timeout.

Since mac80211 was modified to accept incoming frames
once drv_resume was called, we can safely revert this
patch, and handle the pending work on iwl_mvm_resume().
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

On resume, all the interrupts are masked (CSR_INT_MASK is 0),
and ict is disabled.

Re-configure them both.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The regular and scheduled scan functions are very similar, so they can
be combined into one.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The iwl_mvm_scan_offload_stop() function is used to stop LMAC regular
scan, stop LMAC scheduled scan and stop UMAC scheduled scans (but not
UMAC regular scans), making it very difficult to read.

Reorganize the scan stopping functions by creating separate functions
to stop regular and scheduled scans, separating the LMAC stopping part
of the code from the rest and renaming the offload_stop function to
iwl_mvm_lmac_scan_stop().
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

After the scan refactor, the order of the SSIDs passed to the firmware
in all scans (including net-detect) are inverted.  This was causing
the reporting code to use the wrong SSIDs.  To fix this, invert the
array index when accessing the saved match SSIDs to report the
wake-up.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

If the device is reset during suspend with net-detect enabled, we
leave the net-detect information dangling and this causes the next
suspend to fail with a warning:

[21795.351010] WARNING: at /root/iwlwifi/iwlwifi-stack-dev/drivers/net/wireless/iwlwifi/mvm/d3.c:989 __iwl_mvm_suspend.isra.6+0x2be/0x460 [iwlmvm]()
[21795.353253] Modules linked in: iwlmvm(O) iwlwifi(O) mac80211(O) cfg80211(O) compat(O) [...]
[21795.366168] CPU: 1 PID: 3645 Comm: bash Tainted: G           O 3.10.29-dev #1
[21795.368785] Hardware name: Dell Inc. Latitude E6430/0CPWYR, BIOS A09 12/13/2012
[21795.371441]  f8ec6748 f8ec6748 e51f3ce8 c168aa62 e51f3d10 c103a824 c1871238 f8ec6748
[21795.374228]  000003dd f8eb982e f8eb982e 00000000 c3408ed4 c41edbbc e51f3d20 c103a862
[21795.377006]  00000009 00000000 e51f3da8 f8eb982e c41ee3dc 00000004 e7970000 e51f3d74
[21795.379792] Call Trace:
[21795.382461]  [<c168aa62>] dump_stack+0x16/0x18
[21795.385133]  [<c103a824>] warn_slowpath_common+0x64/0x80
[21795.387803]  [<f8eb982e>] ? __iwl_mvm_suspend.isra.6+0x2be/0x460 [iwlmvm]
[21795.390485]  [<f8eb982e>] ? __iwl_mvm_suspend.isra.6+0x2be/0x460 [iwlmvm]
[21795.393124]  [<c103a862>] warn_slowpath_null+0x22/0x30
[21795.395787]  [<f8eb982e>] __iwl_mvm_suspend.isra.6+0x2be/0x460 [iwlmvm]
[21795.398464]  [<f8eb9d7c>] iwl_mvm_suspend+0xec/0x140 [iwlmvm]
[21795.401127]  [<c104be11>] ? del_timer_sync+0xa1/0xc0
[21795.403800]  [<f8d4107e>] __ieee80211_suspend+0x1de/0xff0 [mac80211]
[21795.406459]  [<c168e43d>] ? mutex_lock_nested+0x25d/0x350
[21795.409084]  [<c1586b64>] ? rtnl_lock+0x14/0x20
[21795.411685]  [<f8cf0076>] ieee80211_suspend+0x16/0x20 [mac80211]
[21795.414318]  [<f8c4e014>] wiphy_suspend+0x74/0x710 [cfg80211]
[21795.416916]  [<c141e612>] __device_suspend+0x1e2/0x220
[21795.419521]  [<f8c4dfa0>] ? addresses_show+0xa0/0xa0 [cfg80211]
[21795.422097]  [<c141f997>] dpm_suspend+0x67/0x210
[21795.424661]  [<c141fd6f>] dpm_suspend_start+0x4f/0x60
[21795.427219]  [<c108d8e0>] suspend_devices_and_enter+0x60/0x480
[21795.429768]  [<c168646a>] ? printk+0x4d/0x4f
[21795.432295]  [<c108de76>] pm_suspend+0x176/0x210
[21795.434830]  [<c108ca5d>] state_store+0x5d/0xb0
[21795.437410]  [<c108ca00>] ? wakeup_count_show+0x50/0x50
[21795.439961]  [<c13208db>] kobj_attr_store+0x1b/0x30
[21795.442514]  [<c11e3a4b>] sysfs_write_file+0xab/0x100
[21795.445088]  [<c11e39a0>] ? sysfs_poll+0xa0/0xa0
[21795.447659]  [<c1179655>] vfs_write+0xa5/0x1c0
[21795.450212]  [<c1179af7>] SyS_write+0x57/0xa0
[21795.452699]  [<c1699ec1>] sysenter_do_call+0x12/0x32
[21795.455146] ---[ end trace faf5321baba2bfdb ]---

To fix this, call the iwl_mvm_free_nd() function in case of any error
during resume.  Additionally, rename the "out_unlock" label to err to
make it clearer that it's only called in error conditions.

Cc: stable@vger.kernel.org [3.19+]
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The __iwl_mvm_resume() function always returns 1, which causes
mac80211 to do a reconfig with IEEE80211_RECONFIG_TYPE_RESTART.  This
type of reconfig calls iwl_mvm_restart_complete(), where we unref the
IWL_MVM_REF_UCODE_DOWN, so we should always take the reference in this
case.

This prevents this kind of warning from happening:

[40026.103025] WARNING: at /root/iwlwifi/iwlwifi-stack-dev/drivers/net/wireless/iwlwifi/mvm/mac80211.c:236 iwl_mvm_unref+0xc9/0xd0 [iwlmvm]()
[40026.105145] Modules linked in: iwlmvm(O) iwlwifi(O) mac80211(O) cfg80211(O) compat(O) ctr ccm arc4 autofs4 snd_hda_codec_hdmi snd_hda_codec_idt joydev coretemp kvm_intel kvm aesni_intel ablk_helper cryptd lrw aes_i586 snd_hda_intel xts snd_hda_codec gf128mul snd_hwdep snd_pcm snd_seq_midi dell_wmi snd_rawmidi sparse_keymap snd_seq_midi_event snd_seq uvcvideo dell_laptop videobuf2_core dcdbas microcode videodev psmouse snd_timer videobuf2_vmalloc videobuf2_memops serio_raw snd_seq_device btusb i915 snd bluetooth lpc_ich drm_kms_helper soundcore snd_page_alloc drm i2c_algo_bit wmi parport_pc ppdev video binfmt_misc rpcsec_gss_krb5 nfsd mac_hid nfs_acl nfsv4 auth_rpcgss nfs fscache lockd sunrpc msdos lp parport sdhci_pci sdhci ahci libahci e1000e mmc_core ptp pps_core [last unloaded: compat]
[40026.117640] CPU: 2 PID: 3827 Comm: bash Tainted: G        W  O 3.10.29-dev #1
[40026.120216] Hardware name: Dell Inc. Latitude E6430/0CPWYR, BIOS A09 12/13/2012
[40026.122815]  f8effd18 f8effd18 e740fd18 c168aa62 e740fd40 c103a824 c1871238 f8effd18
[40026.125527]  000000ec f8ec79c9 f8ec79c9 d5d29ba4 d5d2a20c 00000000 e740fd50 c103a862
[40026.128209]  00000009 00000000 e740fd7c f8ec79c9 f1c591c4 00000400 00000000 f8efb490
[40026.130886] Call Trace:
[40026.133506]  [<c168aa62>] dump_stack+0x16/0x18
[40026.136115]  [<c103a824>] warn_slowpath_common+0x64/0x80
[40026.138727]  [<f8ec79c9>] ? iwl_mvm_unref+0xc9/0xd0 [iwlmvm]
[40026.141319]  [<f8ec79c9>] ? iwl_mvm_unref+0xc9/0xd0 [iwlmvm]
[40026.143881]  [<c103a862>] warn_slowpath_null+0x22/0x30
[40026.146453]  [<f8ec79c9>] iwl_mvm_unref+0xc9/0xd0 [iwlmvm]
[40026.149030]  [<f8ec7a4d>] iwl_mvm_mac_reconfig_complete+0x7d/0x210 [iwlmvm]
[40026.151645]  [<f8b74b20>] ? ftrace_raw_event_drv_reconfig_complete+0xc0/0xe0 [mac80211]
[40026.154291]  [<f8b6769e>] ieee80211_reconfig+0x28e/0x2620 [mac80211]
[40026.156920]  [<c10ef0ea>] ? ring_buffer_unlock_commit+0xba/0x100
[40026.159585]  [<f8b4a04d>] ieee80211_resume+0x6d/0x80 [mac80211]
[40026.162206]  [<f8a79722>] wiphy_resume+0x72/0x260 [cfg80211]
[40026.164799]  [<c141e2e7>] ? device_resume+0x57/0x150
[40026.167425]  [<f8a796b0>] ? wiphy_suspend+0x710/0x710 [cfg80211]
[40026.170075]  [<c141e26e>] dpm_run_callback+0x2e/0x50
[40026.172695]  [<c141e321>] device_resume+0x91/0x150
[40026.175334]  [<c141f636>] dpm_resume+0xf6/0x200
[40026.177922]  [<c141f920>] dpm_resume_end+0x10/0x20
[40026.180489]  [<c108d9f7>] suspend_devices_and_enter+0x177/0x480
[40026.183037]  [<c168646a>] ? printk+0x4d/0x4f
[40026.185559]  [<c108de76>] pm_suspend+0x176/0x210
[40026.188065]  [<c108ca5d>] state_store+0x5d/0xb0
[40026.190581]  [<c108ca00>] ? wakeup_count_show+0x50/0x50
[40026.193052]  [<c13208db>] kobj_attr_store+0x1b/0x30
[40026.195608]  [<c11e3a4b>] sysfs_write_file+0xab/0x100
[40026.198055]  [<c11e39a0>] ? sysfs_poll+0xa0/0xa0
[40026.200469]  [<c1179655>] vfs_write+0xa5/0x1c0
[40026.202893]  [<c1179af7>] SyS_write+0x57/0xa0
[40026.205245]  [<c1699ec1>] sysenter_do_call+0x12/0x32
[40026.207619] ---[ end trace db1d5a72a0381b0a ]---
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NEliadX Peller <eliad@wizery.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

fw_status is the only pointer pointing to a block of memory
allocated above and should be freed after use.
Note: this come from Klockwork static analyzer.

Cc: stable@vger.kernel.org [3.19+]
Fixes: 2021a89d ("iwlwifi: mvm: treat netdetect wake up separately")
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Net-detect scans were using the same type as sched scan, which was
causing the driver to return -EBUSY and prevent the system from
suspending if there was an ongoing scheduled scan.  To avoid this, add
a new type for net-detect and don't stop anything when it is
requested, so that the existing scheduled scan will be resumed when
the system wakes up.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

All scans are using the unified APIs now, so using "unified" in the
symbols is useless and just make them much longer and the main
difference between scans now is LMAC vs. UMAC.  Remove "unified" from
all relevant symbols.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

I forgot to rename the CPTCFG_ prefix...

Fixes: 484b3d13 ("iwlwifi: mvm: add debugfs entry with the number of net-detect scans")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Our testers need to know the number of scans performed while in
net-detect mode before the device wakes up.  The firmware already
passes this information to the driver, so we can save it and report it
in a debugfs entry.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

we unref IWL_MVM_REF_UCODE_DOWN on iwl_mvm_restart_complete().

Usually, the restart is initiated by iwl_mvm_nic_restart(),
which takes the reference before restarting the hw.

However, in D3 flow we might call ieee80211_restart_hw()
directly (in case of suspend error and on d3_test-resume),
which without taking the ref first. fix it.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The return value in iwl_mvm_get_wakeup_status() is a bit unclear in
that it's not obvious that we don't leak fw_status in some cases.
Use fw_status directly with ERR_PTR() and return only it, that way
the compiler has a chance of proving that it's uninitialized (if it
ever is due to new changes.)

Additionally, this removes a smatch warning since smatch couldn't
figure out that fw_status can't, in fact, leak here.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When IWLWIFI_DEBUGFS is not set, we should not unlock the mutex after
calling iwl_mvm_query_wakeup_reasons(), because this function unlocks
it already.  Move the goto out_iterate outside the #ifdef.

Change-Id: I13d86402aecf0eeec44b1abbe2b244fbc706a5eb
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

When moving to the D3 FW give it the valid MCC from the D0 FW. When
returning from D3 to D0, query the D3 FW for the latest MCC, as
it might have changed internally. This MCC will be replayed to the D0 FW
when it boots.
Signed-off-by: NJonathan Doron <jonathanx.doron@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We shouldn't call iwl_mvm_d3_disconnect_iter() on the running
interfaces when we are woken up due to net-detect, because it doesn't
make sense.  Additionally, this seems to set the
IEEE80211_SDATA_DISCONNECT_RESUME flag that will cause a disconnection
on the next resume (if a normal WoWLAN is used).

To solve this, skip the iteration loop when net-detect is set.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reported-by: NSamuel Tan <samueltan@chromium.org>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

A number of places (still) use a direct operation, use
iwl_mvm_sta_from_mac80211() consistently. In one place
also move it into the variable initializer.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enter d0i3 on suspend, and exit d0i3. Wait for the
command responses in both cases.

Use this mode in case of pcie trans.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

d3 and d0i3 shouldn't be mutually exclusive. Set supported
wowlan triggers by looking for each of them, and check
on suspend/resume which flow should be used ("any" trigger
is supported by d0i3, and all the others by d3)
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add the channels on which there was a match for every match reported
by the firmware.  The firmware reports the channels as indices to the
array of channels that was passed in the scheduled scan request, so we
need to save the array when entering D3 to make sure it is available
when we resume.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add SSID information to the net-detect indication to userspace.  Fetch
the matched profiles from the firmware in order to find the correct
SSIDs in the profiles that matched.

Since the net-detect information is stored in cfg80211, and in theory
it could change while we are waking up and reading the matched
profiles, we need to save it when we enter D3 so it is available
during resume.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>