Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 04 1月, 2013 3 次提交
    • S
      USB: Ignore xHCI Reset Device status. · 8b8132bc
      由 Sarah Sharp 提交于 
      When the USB core finishes reseting a USB device, the xHCI driver sends
a Reset Device command to the host.  The xHC then updates its internal
representation of the USB device to the 'Default' device state.  If the
device was already in the Default state, the xHC will complete the
command with an error status.

If a device needs to be reset several times during enumeration, the
second reset will always fail because of the xHCI Reset Device command.
This can cause issues during enumeration.

For example, usb_reset_and_verify_device calls into hub_port_init in a
loop.  Say that on the first call into hub_port_init, the device is
successfully reset, but doesn't respond to several set address control
transfers.  Then the port will be disabled, but the udev will remain in
tact.  usb_reset_and_verify_device will call into hub_port_init again.

On the second call into hub_port_init, the device will be reset, and the
xHCI driver will issue a Reset Device command.  This command will fail
(because the device is already in the Default state), and
usb_reset_and_verify_device will fail.  The port will be disabled, and
the device won't be able to enumerate.

Fix this by ignoring the return value of the HCD reset_device callback.

This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72 "usbcore: refine
warm reset logic".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
      8b8132bc
    • S
      USB: Handle auto-transition from hot to warm reset. · 1c7439c6
      由 Sarah Sharp 提交于 
      USB 3.0 hubs and roothubs will automatically transition a failed hot
reset to a warm (BH) reset.  In that case, the warm reset change bit
will be set, and the link state change bit may also be set.  Change
hub_port_finish_reset to unconditionally clear those change bits for USB
3.0 hubs.  If these bits are not cleared, we may lose port change events
from the roothub.

This commit should be backported to kernels as old as 3.2, that contain
the commit 75d7cf72 "usbcore: refine
warm reset logic".
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
      1c7439c6
    • S
      xhci: Handle HS bulk/ctrl endpoints that don't NAK. · 55c1945e
      由 Sarah Sharp 提交于 
      A high speed control or bulk endpoint may have bInterval set to zero,
which means it does not NAK.  If bInterval is non-zero, it means the
endpoint NAKs at a rate of 2^(bInterval - 1).

The xHCI code to compute the NAK interval does not handle the special
case of zero properly.  The current code unconditionally subtracts one
from bInterval and uses it as an exponent.  This causes a very large
bInterval to be used, and warning messages like these will be printed:

usb 1-1: ep 0x1 - rounding interval to 32768 microframes, ep desc says 0 microframes

This may cause the xHCI host hardware to reject the Configure Endpoint
command, which means the HS device will be unusable under xHCI ports.

This patch should be backported to kernels as old as 2.6.31, that contain
commit dfa49c4a "USB: xhci - fix math in
xhci_get_endpoint_interval()".
Reported-by: NVincent Pelletier <plr.vincent@gmail.com>
Suggested-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
      55c1945e
  3. 18 12月, 2012 2 次提交
  5. 17 12月, 2012 1 次提交
  7. 01 12月, 2012 1 次提交
    • T
      ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h · 45c3eb7d
      由 Tony Lindgren 提交于 
      Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.

Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.

So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.

The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.

Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.

Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.

Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.

Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.

[1] https://patchwork.kernel.org/patch/1519591/#

cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      45c3eb7d
  9. 29 11月, 2012 2 次提交
  11. 27 11月, 2012 8 次提交
  13. 24 11月, 2012 1 次提交
  15. 22 11月, 2012 22 次提交