[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Probe/remove functions need to be marked as __devinit and __devexit
(not __init an __exit) to prevent trying to run code that has been
discarded.  This patch fixes the spi_imx driver to mark probe and
remove correctly.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This change adds the OMAP SPI 100k driver created by
Fabrice Crohas <fcrohas@gmail.com>.  This SPI bus is found on
OMAP7xx-series smartphones, and for many, the touchscreen is
attached to this bus.

The lion's share of the work was done by Fabrice on this driver --
I am merely porting it from the Linwizard project on his behalf.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Also there is no casting needed to assign a void pointer.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This is much safer when support for new variants is added.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

platform_get_irq returns -ENXIO if there is no entry.  So ensure
return value is greater than zero instead of non-zero.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NWan ZongShun <mcuos.com@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch is V2 of SPI Master support for the SuperH MSIOF.
Full duplex, spi mode 0-3, active high cs, 3-wire and lsb
first should all be supported, but the driver has so far
only been tested with "mmc_spi".

The MSIOF hardware comes with 32-bit FIFOs for receive and
transmit, and this driver simply breaks the SPI messages
into FIFO-sized chunks. The MSIOF hardware manages the pins
for clock, receive and transmit (sck/miso/mosi), but the chip
select pin is managed by software and must be configured as
a regular GPIO pin by the board code.

Performance wise there is still room for improvement, but
on a Ecovec board with the built-in sh7724 MSIOF0 this driver
gets Mini-sd read speeds of about half a megabyte per second.

Future work include better clock setup and merging of 8-bit
transfers into 32-bit words to reduce interrupt load and
improve throughput.
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

When VERBOSE is defined in the spidev module, the compilation
will throw an error on 'spi' not being defined:

CC [M]  drivers/spi/spidev.o
drivers/spi/spidev.c: In function 'spidev_message':
drivers/spi/spidev.c:266: error: 'spi' undeclared (first use in this function)
drivers/spi/spidev.c:266: error: (Each undeclared identifier is reported only once
drivers/spi/spidev.c:266: error: for each function it appears in.)

instead of using spi-> we should actually use spidev->spi.
This patch fixes the build failure.
Signed-off-by: NFlorian Fainelli <ffainelli@freebox.fr>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

fix setupxfer() not to override generic configuration of speed_hz
and bits_per_word with zeros
Signed-off-by: NJan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The function plat_mpc8xxx_spi_remove is defined using __devexit, so don't
use __exit_p but __devexit_p to wrap it.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

i.MX35-provided chipselects are represented using negative numbers. If
gpio_request() fails and the previous chipselect was a negative number,
the while loop is endless (i is never decremented).

Also, the error loop would never call gpio_free on chipselect[0].

And finally, the error message was missing an endline.
Signed-off-by: NJohn Ogness <john.ogness@linutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

On the MX31litekit, the bootloader seems to communicate with the MC13783
PMIC chip before booting Linux. However, it does not flush all the
buffers properly after that, which makes the imx-spi driver read
bogus data when probing the MC13783.

Fix that by draining the SPI receive buffer on startup.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NAndrew Morton <akpm@linux-foundation.org>

This patch fixes the error exposed by the following build warning:

drivers/spi/xilinx_spi.c: In function 'xilinx_spi_init':
drivers/spi/xilinx_spi.c:411: warning: cast from pointer to integer
of different size

Fixed by change %x to %p in the format string.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

- drop own, obsolete include-file
- drop IRQF_SAMPLE_RANDOM (deprecated feature)
- drop 'if' above kfree()
- typos, braces & whitespaces
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NLuotao Fu <l.fu@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds in a platform device driver using the xilinx_spi common module.
Tested-by: NJohn Linn <John.Linn@xilinx.com>
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds in support for the DS570 IP.

It's register compatible with the DS464, but adds support for 8/16/32 SPI.

The 8/16/32 support is added by attaching callbacks reading/writing the
proper amount of data. To indicate to the driver which amount of bits
to use a new field is introduced in the platform data struct.
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NJohn Linn <John.Linn@xilinx.com>
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch changes the out_(be)(8|16|32) and in_(be)(8|16|32) calls to 32 bits ioread/iowrite.

The read and write function are attached to the internal struct as callbacks, callback
is selected depending on endianess.

This will also build on platforms not supporting the in/out calls for instance x86.
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Tested-by: NJohn Linn <John.Linn@xilinx.com>
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch splits the xilinx_spi driver into a generic part and a
OF driver part.

The reason for this is to later add in a platform driver as well.
Tested-by: NJohn Linn <John.Linn@xilinx.com>
Signed-off-by: NRichard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This one enables the mpc52xx_spi driver for usage of user defined gpio lines
as chipselect. This way we can control some more spi devices than only one

V2 Changes:
* preinitialize the gpio as output in probe function and call gpio_set_value in
  the chip select function instead of calling direction_output every time.
* initialize the gpio line with output high, since we don't support CS_HIGH
  in the driver currently any way. change gpio value setting to default active
  low in chip select call.
* free the gpio array while error or removing.
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

V2 changes:
* remove CS_HIGH mode
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Before reading status register to check MODF failure, we have to clear it
first since the MODF flag will be set after initializing the spi master,
if the hardware comes up with a low SS. The processor datasheet reads:
Mode Fault flag -- bit sets if SS input goes low while SPI is configured as a
master. Flag is cleared automatically by an SPI status register read (with MODF
set) followed by a SPI control register 1 write.
Hence simply rereading the register is not sufficient to clear the flag. We
redo the write also to make sure to clear the flag.

V2 Changes:
* change variable type from int to u8
Signed-off-by: NLuotao Fu <l.fu@pengutronix.de>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Remove the old WDT implementation.
Signed-off-by: NAlbrecht Dreß <albrecht.dress@arcor.de>
Acked-by: NWim Van Sebroeck <wim@iguana.be>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Merge the WDT code into the GPT interface.
Signed-off-by: NAlbrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add the "fsl,wdt-on-boot" OF property as to reserve a GPT as WDT which may
be a requirement in safety-related (e.g. ISO/EN 61508) applications.
Signed-off-by: NAlbrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch changes the period parameter of mpc52xx_gpt_start_timer to
a u64 to support larger timeout periods.
Signed-off-by: NAlbrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Driver cannot be used as a module without this patch.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This trivial patch changes memcpy_(to|from)io as to transfer as many
32-bit words as possible in 32-bit accesses (in the current solution,
the last 32-bit word was transferred as 4 byte accesses).
Signed-off-by: NAlbrecht Dreß <albrecht.dress@arcor.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

To easily identify which device has problems.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

The bits_per_word value can be set for each transfer, or can
be set to zero in each transfer in which case it should default
to the value in the driver.

The driver was fixed to properly check the bits_per_word in
the transfer that is passed in.
Signed-off-by: NJohn Linn <john.linn@xilinx.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This driver calls mpc52xx_set_psc_clkdiv() but doesn't check its return value
to see if the PSC is actually valid for SPI use. Add the check and a hint for
the user.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This is a driver for the FIFO device on the LocalPlus bus on an mpc5200 system.
The driver supports programmed I/O through the FIFO as well as setting up DMA
via the BestComm engine through the FIFO.
Signed-off-by: NJohn Bonesio <bones@secretlab.ca>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

This patch adds an interface for controlling the timer function of the
MPC5200 GPT devices.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Adds support for the dedicated SPI device on the Freescale MPC5200(b)
SoC.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add call to of_register_spi_devices() to register SPI devices described
in the OF device tree.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>

* 'for-linus' of git://github.com/at91linux/linux-2.6-at91:
  at91: at91sam9g45 family: identify several chip versions
  avr32: add two new at91 to cpu.h definition

cpu_is_xxx() macros are identifying generic at91sam9g45 chip. This patch adds
the capacity to differentiate Engineering Samples and final lots through the
inclusion of  at91_cpu_fully_identify() and the related chip IDs with chip
version field preserved.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NHans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>