Adding a enable parameters allow us to share most of the code between
enable and disable functions.

v3:
Renamed icl_phy_clock_gating() to icl_phy_set_clock_gating()
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920205810.211048-6-jose.souza@intel.com

Step 4.b was complete missed because it is only required to TC and TBT.

Bspec: 49190
Reviewed-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NClinton A Taylor <clinton.a.taylor@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190920205810.211048-2-jose.souza@intel.com

crtc_state->limited_color_range only applies to RGB output but
we're currently setting it even for YCbCr output. That will
lead to conflicting MSA and PIPECONF settings which can mess
up the image. Let's make sure limited_color_range stays unset
with YCbCr output.

Also WARN if we end up with such a bogus combination when
programming the MSA MISC bits as it's impossible to even
indicate quantization rangle for YCbCr via MSA MISC. YCbCr
output is simply assumed to be limited range always. Note
that VSC SDP does provide a mechanism for full range YCbCr,
so in the future we may want to rethink how we compute/store
this state.

And for good measure we add the same WARN to the HDMI path.

v2: s/==/!=/ in the HDMI WARN
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718164523.11738-1-ville.syrjala@linux.intel.comReviewed-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>

Looks like we're currently setting the MSA to xvYCC BT.709 instead
of the YCbCr BT.601 claimed by the comment. But even that comment
is wrong since we configure the CSC matrix to BT.709.

Let's remove the bogus statement from the comment and fix the
MSA to indicate YCbCr BT.709 so that it matches the actual
pixel data we're transmitting.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190718145053.25808-3-ville.syrjala@linux.intel.comReviewed-by: NGwan-gyeong Mun <gwan-gyeong.mun@intel.com>

Gen 12 onwards moves the DP_TP_* registers to be transcoder-based rather
than port-based. This adds the new register addresses and changes all
the callers to use the register saved in intel_dp->regs.*. This is
filled out when preparing to enable the port so we take into account if
we should use the transcoder or the port.

v2: reimplement by stashing the registers we want to access under
intel_dp->reg. Now they are initialized when enabling the port.
Ville suggested to store the transcoder to be used exclusively
by TGL+. After implementing I thought just storing the register directly
made it cleaner.

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904213419.27547-5-jose.souza@intel.comSigned-off-by: NJosé Roberto de Souza <jose.souza@intel.com>

DP_TP_{CTL,STATUS} should only be programmed when the encoder is intel_dp.
Checking its current usages intel_disable_ddi_buf() is the only
offender, with other places being protected by checks like
pipe_config->fec_enable that is only set by intel_dp.

v3 (José):
- Using intel_crtc_has_dp_encoder() instead of intel_encoder_is_dp()
(Ville)

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190904213419.27547-4-jose.souza@intel.comSigned-off-by: NJosé Roberto de Souza <jose.souza@intel.com>

enum port is a mess now because it no longer matches the spec
at all. Let's start to dig ourselves out of this hole by
reducing our reliance on port_name(). This should at least make
a bunch of debug messages a bit more sensible while we think how
to fill the the hole properly.

Based on the following cocci script with a lot of manual cleanup
(all the format strings etc.):
@@
expression E;
@@
(
- port_name(E->port)
+ E->base.base.id, E->base.name
|
- port_name(E.port)
+ E.base.base.id, E.base.name
)

@@
enum port P;
expression E;
@@
  P = E->port
<...
- port_name(P)
+ E->base.base.id, E->base.name
...>

@@
enum port P;
expression E;
@@
  P = E.port
<...
- port_name(P)
+ E.base.base.id, E.base.name
...>

@@
expression E;
@@
{
- enum port P = E;
... when != P
}
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190830182719.32608-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

On TGL some registers moved from DDI to transcoder and the
DisplayPort training sequence has a separate BSpec page.

I started adding 'ifs' to the original intel_ddi_pre_enable_dp() but
it was becoming really hard to follow, so a new and cleaner function
for TGL was added with comments of all steps. It's similar to ICL,
but different enough to deserve a new function.

The rest of DisplayPort enable and the whole disable sequences
remained the same.

v2: FEC and DSC should be enabled on sink side before start link
training(Maarten reported and Manasi confirmed the DSC part)

v3: Add call to enable FEC on step 7.l(Manasi)

BSpec: 49190
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-16-lucas.demarchi@intel.com

The conversion during HDMI HW readout from port_clock to crtc_clock was
missed when HDMI 10bpc support was added, so fix that.

v2:
- Unscrew the non-HDMI case.

Fixes: cd9e11a8 ("drm/i915/icl: Add 10-bit support for hdmi")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109593
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808162547.7009-1-imre.deak@intel.com

To reduce the number of explicit dev_priv->uncore calls in the display
code ahead of the introduction of dev_priv->de_uncore, this patch
introduces a wrapper for one of the main usages of it, the register
waits. When we transition to the new uncore, we can just update the
wrapper to point to the appropriate structure.

Since the vast majority of waits are on a set or clear of a bit or mask,
add set & clear flavours of the wrapper to simplify the code.
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190816012343.36433-7-daniele.ceraolospurio@intel.com

When getting the pipes attached to encoder if it is not a eDP encoder
it iterates over all pipes and read a transcoder register.
But it should not read a transcoder register before get its power
domain.

It was not a issue in gens older than 12 because if it only had
port A connected it would be attached to EDP and it would skip all
the transcoders readout, if it had more than one port connected,
pipe B would cause PG3 to be on and it contains all other
transcoders.

But on gen 12 there is no EDP transcoder so it is always iterating
over all pipes and if only one sink is connected, PG3 is kept off
and reading other transcoders registers would cause a
unclaimed read warning.

So here getting the power domain of the transcoder only if it is
enabled, otherwise it is not connected to the DDI.
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190808004935.1787-1-jose.souza@intel.com

Everything about the file is about display, and mostly about types
related to display. Move under display/ as intel_display_types.h to
reflect the facts.

There's still plenty to clean up, but start off with moving the file
where it logically belongs and naming according to contents.

v2: fix the include guard name in the renamed file
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806113933.11799-1-jani.nikula@intel.com

Attaches the content type property for HDCP2.2 capable connectors.

Implements the update of content type from property and apply the
restriction on HDCP version selection.

Need ACK for content type property from userspace consumer.

v2:
  s/cp_content_type/content_protection_type [daniel]
  disable at hdcp_atomic_check to avoid check at atomic_set_property
	[Maarten]
v3:
  s/content_protection_type/hdcp_content_type [Pekka]
v4:
  hdcp disable incase of type change is moved into commit [daniel].
v5:
  Simplified the Type change procedure. [Daniel]
v6:
  Type change with UNDESIRED state is ignored.
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: NPekka Paalanen <pekka.paalanen@collabora.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/320959/?series=57232&rev=14

Specification states that DDI_CLK_SEL needs to be mapped to MG clock
even if MG do not exist on EHL, this will ungate those DDIs.

BSpec: 20845
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Tested-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190730175121.16413-1-jose.souza@intel.com

Bit definitions for port-select got changed for TRANS_CLK_SEL &
TRANS_DDI_FUNC_CTL registers in TGL.

v2 (Lucas):
  - Nuke TRANS_DDI_PORT_NONE since it's 0: we are already clearing
    {TGL_,}TRANS_DDI_PORT_MASK (suggested by Ville)
  - Also cover haswell_get_ddi_port_state() in intel_display.c that was
    missing
  - Define macros using the _SHIFT macros so we don't lose other users

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NMatt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190713010940.17711-3-lucas.demarchi@intel.com

Right now we are aware of two cases that needs another hotplug retry:
- Unpowered type-c dongles
- HDMI slow unplug

Both have a complete explanation in the code to schedule another run
of the hotplug handler.

It could have more checks to just trigger the retry in those two
specific cases but why would sink signal a long pulse if there is
no change? Also the drawback of running the hotplug handler again
is really low and that could fix another cases that we are not
aware.

Also retrying for old DP ports(non-DDI) to make it consistent and not
cause CI failures if those systems are connected to chamelium boards
that will be used to simulate the issues reported in here.

v2: Also retrying for old DP ports(non-DDI)(Imre)

v4: Renamed INTEL_HOTPLUG_NOCHANGE to INTEL_HOTPLUG_UNCHANGED to keep
it consistent(Rodrigo)
Tested-by: NTimo Aaltonen <tjaalton@ubuntu.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712005343.24571-2-jose.souza@intel.com

There is some scenarios that we are aware that sink probe can fail,
so lets add the infrastructure to let hotplug() hook to request
another probe after some time.

v2: Handle shared HPD pins (Imre)
v3: Rebased
v4: Renamed INTEL_HOTPLUG_NOCHANGE to INTEL_HOTPLUG_UNCHANGED to keep
it consistent(Rodrigo)
v5: Making the working queue used explicit through all the callers to
hotplug_work (Ville)
Tested-by: NTimo Aaltonen <tjaalton@ubuntu.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712005343.24571-1-jose.souza@intel.com

There are 2 new additional typeC ports in Tiger Lake and PORT-C is now a
combophy port. This results in 6 typeC ports and 3 combophy ports.
These 6 TC ports can be DP alternate mode, DP over thunderbolt, native
DP on legacy DP connector or native HDMI on legacy connector.

v2: Rebase on new modular FIA code (Lucas)
v3: Also add new port in port_identifier(), even though it can't
    possibly be used there (requested by José)
v4: Add conversion port->tc_port in helper function after introction of
    phy namespace (Lucas)

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: NVandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190711173115.28296-13-lucas.demarchi@intel.com

Transition the remaining uses of intel_port_is_* over to the equivalent
intel_phy_is_* functions and drop the port functions.

v5: Fix a call in a debug function that's only called when
    CONFIG_DRM_I915_DEBUG_RUNTIME_PM is on.  (CI)

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-5-matthew.d.roper@intel.com

Convert the code that operates directly on gen11 combo PHY's to use the
new namespace.  Combo PHY registers are those named "ICL_PORT_*" plus
ICL_DPHY_CHKN.

Note that a lot of the PHY programming happens in the MIPI DSI code.
For clarity I've added a for_each_dsi_phy() to loop over the phys used
by DSI.  Since DSI always uses A & B on gen11, port=phy in all cases so
it doesn't actually matter which form we use in the DSI code.  I've used
the phy iterator in code that's explicitly working with the combo PHY,
but left the rest of the DSI code using the port iterator and namespace
to minimize patch deltas.  We can switch the rest of the DSI code over
to use phy terminology later if this winds up being too confusing.

v6: Drop an include of drm/i915_drm.h; that was previously included just
    for the definition of 'enum port' which this patch removes the need
    for.  (Jose)

Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-4-matthew.d.roper@intel.com

Although the register name implies that it operates on DDI's,
DPCLKA_CFGCR0_ICL actually needs to be programmed according to the PHY
that's in use.  I.e., when using EHL's DDI-D on combo PHY A, the bits
described as "port A" in the bspec are what we need to set.  The bspec
clarifies:

        "[For EHL] DDID clock tied to DDIA clock, so DPCLKA_CFGCR0 DDIA
        Clock Select chooses the PLL for both DDIA and DDID and drives
        port A in all cases."

Also, since the CNL DPCLKA_CFGCR0 bit defines are still port-based, we
create separate ICL-specific defines that accept the PHY rather than
trying to share the same bit definitions between CNL and ICL.

v5: Make icl_dpclka_cfgcr0_clk_off() take phy rather than port.  When
    splitting the original patch the hunk to handle this wound up too
    late in the series.  (Sparse)

v6: Since we're already changing this code,
    s/DPCLKA_CFGCR0_ICL/ICL_DPCLKA_CFGCR0/ for consistency.  (Jose)

Bspec: 33148
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190709183934.445-3-matthew.d.roper@intel.com

PORT_TX_DFLEXDPMLE1 is a FIA register so move it to intel_tc.c where we
access other FIA registers. In Tiger Lake we have multiple/modular FIAs
so it makes sense to start moving all access to their registers to a
common place.

While at it, make it clear that we will only ever call this function
for ports with TC phy. Previously we were relying on tc_mode being
TC_PORT_TBT_ALT for combo phy ports. However it's confusing since in
this same function we have checks for is_tc_port. Also, if we manage to
make each phy access only their own field, we may in future add them as
a union inside intel_digital_port.

v2: Fix coding style while moving the code
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190708172815.6814-4-lucas.demarchi@intel.com

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpu/drm/i915/display/intel_ddi.c: In function 'intel_ddi_get_config':
drivers/gpu/drm/i915/display/intel_ddi.c:3774:29: warning:
 variable 'intel_dig_port' set but not used [-Wunused-but-set-variable]
  struct intel_digital_port *intel_dig_port;

It is never used, so can be removed.
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190705113138.65880-1-yuehaibing@huawei.com

The port parameter hasn't been used since the last bspec phy programming
update.  Drop it to make some upcoming changes simpler.

References: 9659c1af ("drm/i915/icl: combo port vswing programming changes per BSPEC")
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NClint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190626000352.31926-2-matthew.d.roper@intel.com

Lane reversal happens only in the FIA module for TBT-alt/DP-alt mode, so
WARN if lane reversal is attempted at a different level. See the
BSpec DDI_BUF_CTL register description.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-24-imre.deak@intel.com

Disconnecting the TypeC PHY when the port is in legacy mode is not
necessary:
- BSpec doesn't specify a disconnect sequence for legacy mode.
- The use of the PHY is dedicated for the display in legacy mode.
- We keep the PHY always connected during runtime as well in legacy
  mode.

We disconnect the PHY when needed during a disabling modeset for the
port, so we can also remove the disconnect call from the destroy hook.

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-23-imre.deak@intel.com

The TypeC port mode needs to stay fixed whenever the port is active. Do
that by introducing a tc_link_refcount to account for active ports,
avoiding changing the port mode if a reference is held.

During the modeset commit phase we also have to reset the port mode and
update the active PLL reflecting the new port mode. We can do this only
once the port and its old PLL has been already disabled. Add the new
encoder update_prepare/complete hooks that are called around the whole
enabling sequence. The TypeC specific hooks of these will reset the port
mode, update the active PLL if the port will be active and ensure that
the port mode will stay fixed for the duration of the whole enabling
sequence by holding a tc_link_refcount.

During the port enabling, the pre_pll_enable/post_pll_disable hooks will
take/release a tc_link_refcount to ensure the port mode stays fixed
while the port is active.

Changing the port mode should also be avoided during connector detection
and AUX transfers if the port is active, we'll do that by checking the
port's tc_link_refcount.

When resetting the port mode we also have to take into account the
maximum lanes provided by the FIA. It's guaranteed to be 4 in TBT-alt
and legacy modes, but there may be less lanes available in DP-alt mode,
in which case we have to fall back to TBT-alt mode.

While at it also update icl_tc_phy_connect()'s code comment, reflecting
the current way of switching the port mode.

v2:
- Add the update_prepare/complete hooks to the encoder instead of the
  connector. (Ville)
- Simplify intel_connector_needs_modeset() by removing redundant if.
  (Ville)
v3:
- Fix sparse warning, marking static functions as such.
v4:
- Rebase on drm-tip.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-21-imre.deak@intel.com

For using the correct AUX power domains we have to sanitize the TypeC
port mode early, so move that before encoder sanitization. To do this
properly read out the actual port mode instead of just relying on the
VBT legacy port flag (which can be incorrect).

We also verify that the PHY is connected as expected if the port is
active. In case the port is inactive we connect the PHY in case of a
legacy port - as we did so far. The PHY will be connected during
detection for DP-alt mode - as it was done so far. For TBT-alt mode
nothing needs to be done to connect the PHY.

v2:
- Use DRM_DEBUG_KMS instead of DRM_DEBUG_DRIVER. (José)
v3:
- Detect TCCOLD any time PORT_TX_DFLEXDPCSSS is read. (Ville)

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-14-imre.deak@intel.com

Factor out helpers reading/parsing the TypeC specific registers, making
current users of them clearer and letting us use them later.

While at it also:
- Simplify icl_tc_phy_connect() with an early return in legacy mode.
- Simplify the live status check using one bitmask for all HPD bits.
- Remove a micro-optimisation of the repeated safe-mode clearing.
- Make sure we fix the legacy port flag in all cases.

Except for the last two, no functional changes.

v2:
- Don't do reg reads at variable declarations. (Jani)
- Prevent constant truncated compiler warning when assigning the
  valid_hpd_mask. (Nick)
- s/intel_tc_port_get_lane_info/intel_tc_port_get_lane_mask/ (Ville)
v3:
- Make valid_hpd_mask init clear. (Ville)

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-10-imre.deak@intel.com

Unify the TypeC port notation in log messages, so that it matches the
spec. For instance the first ICL TypeC port will read as 'Port C/TC#1'.

v2:
- Format print the name only once. (José)

Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-9-imre.deak@intel.com

According to the spec we should not enable the DDI-IO power domain if
the TypeC port is in the TBT-alt mode, so do that only in the other
TypeC modes or for non-TypeC ports. See the internal BSpec Index/22243.

v2:
- Add the internal BSpec reference to the log message. (José)

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-6-imre.deak@intel.com

The TypeC port mode can switch dynamically, to reflect that better call
the port's mode as 'mode' rather than 'type'.

While at it:
- s/TC_PORT_TBT/TC_PORT_TBT_ALT/ and s/TC_PORT_TYPEC/TC_PORT_DP_ALT/.
  'TYPEC' is ambiguous, TBT_ALT and DP_ALT better match the reality.

- Remove the 'unknown' TypeC port mode. The mode is always known, it's
  the TBT-alt/safe mode after HW reset and after disconnecting the PHY.
  Simplify the tc_port/tc_type checks accordingly.

- Don't WARN if the port mode changes, that can happen normally.

No functional changes.

Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NLucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-5-imre.deak@intel.com

Move the TypeC port handling functions to a new file for clarity.

While at it:
- s/icl_tc_port_connected()/intel_tc_port_connected()/
  icl_tc_phy_disconnect(), will be unexported later.

- s/intel_dp_get_fia_supported_lane_count()/
    intel_tc_port_fia_max_lane_count()/
  It's used for HDMI legacy mode too.

- Simplify function interfaces by passing only dig_port to them.

No functional changes.

v2:
- Fix checkpatch issues: +1/-1 empty lines in intel_tc.c and add
  missing SPDX to intel_tc.h. (Jani)

Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-4-imre.deak@intel.com

Add a new subdirectory for display code, and start off by moving
modesetting output/encoder code. Judging by the include changes, this is
a surprisingly clean operation.

v2:
- move intel_sdvo_regs.h too
- use tabs for Makefile	file lists and sort them

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613084416.6794-2-jani.nikula@intel.com

All AML parts are either KBL ULX or CFL ULX so there is no point
in keeping INTEL_SUBPLATFORM_AML around. As these are the only
CFL ULX parts (normal CFL didn't have Y SKUs) so we'll just
replace IS_AML_ULX with IS_CFL_ULX (it was already paired with
IS_KBL_ULX which accounts for the other half of the AML parts).

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190605162946.19223-2-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

On non-ULT HSW the "special" WRPLL reference clock select
actually means non-SSC. Take that into account when reading
out the WRPLL state.

Also the non-SSC reference may be either 24MHz or 135MHz,
which we can read out from FUSE_STRAP3. The BDW docs actually
say: "also indicates whether the CPU and PCH are in a single
package or separate packages", so it may be that this is not
actually required and we could just assume 135 MHz (just like
the code already did). But it doesn't really hurt to read this
out as the HSW docs aren't quite so clear.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190604200933.29417-5-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Get rid of the pointless LC_FREQ define.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190604200933.29417-3-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Give the PLL control register bits better names on HSW/BDW.

v2: Fix the copy paste fails in SPLL_REF defines (Maarten)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190610133609.27288-1-ville.syrjala@linux.intel.com
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> #irc

It's a bit silly to go through intel_dp.c to assign the
prepare_link_train vfunc for ddi platforms when we can just
assign it directly from intel_ddi.c.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190604140214.9947-1-ville.syrjala@linux.intel.comReviewed-by: NManasi Navare <manasi.d.navare@intel.com>

Added state readout for DRM infoframe and enabled
state validation for DRM infoframe.

v2: Addressed Ville's review comments and dropped the
unused drm infoframe read at intel_hdmi_init.

v3: Removed a redundant platform check as per Ville's
comment.
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1558015817-12025-13-git-send-email-uma.shankar@intel.com