A scan request is split into multiple scan commands queued in
scan_pending_q. Each scan command will be sent to firmware and
its response is handlded one after another.

If any error is detected while parsing IE in command response
buffer the remaining data will be ignored and error is returned.

We should check if there is any more scan commands pending in
the queue before returning error. This ensures that we will call
cfg80211_scan_done if this is the last scan command, or send
next scan command in scan_pending_q to firmware.

Cc: "3.6+" <stable@vger.kernel.org>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In routine _rtl_rx_pre_process(), skb_dequeue() is called to get an skb;
however, the wrong variable name is used in subsequent calls.
Reported-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This issue was reported on the wireless list (see [1]) in which
brcmsmac ran into a fatal error:

[  588.284074] brcmsmac bcma0:0: frameid != txh->TxFrameID
[  588.284098] brcmsmac bcma0:0: MI_TFS: fatal
[  588.284103] brcmsmac bcma0:0: wl0: fatal error, reinitializing
[  588.286208] ieee80211 phy0: Hardware restart was requested

The tx status feedback is processed in a loop limiting the number of
frames processed in one run. The code terminate processing when the
limit is reached regardless the txstatus value read from the device
register. When that status is is flagged as being valid it must be
processed as the hardware will clear it after is has been read.

Bisecting was done by Seth Forshee and showed following commit as the
culprit:

commit 57fe5048
Author: Piotr Haber <phaber@broadcom.com>
Date:   Wed Nov 28 21:44:07 2012 +0100

    brcmsmac: fix bounds checking in tx/rx

[1] http://www.spinics.net/lists/linux-wireless/msg101293.htmlReported-by: NLinus Torvalds <torvalds@linux-foundation.org>
Tested-by: NSeth Forshee <seth.forshee@canonical.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We do a:

	sprintf(buf, " Last beacon: %ums ago",
		elapsed_jiffies_msecs(bss->ts));

elapsed_jiffies_msecs() can return a 10 digit number so "buf" needs to
be 31 characters long.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This reverts commit f590dcec
which has been reported to cause issues.

See https://lkml.org/lkml/2013/1/20/4 for further details.

Cc: stable@vger.kernel.org [3.7]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add missing "!" as we are supposed to check "!card->adapter"
in PCIe suspend handler.

Cc: "3.2+" <stable@vger.kernel.org>
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Reviewed-by: NSergey V. <sftp.mtuci@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Chain swapping should only be enabled when the EEPROM chainmask is set to 5,
regardless of what the runtime chainmask is.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The kbuild test robot reports the following warning with x86_64-randconfig-x955:

warning: (RTL8192CE && RTL8192SE && RTL8192DE && RTL8723AE && RTL8192CU) selects
 RTLWIFI which has unmet direct dependencies (NETDEVICES && WLAN &&
 (RTL8192CE || RTL8192CU || RTL8192SE || RTL8192DE))

This warning was introduced in commit a2905935, "rtlwifi: Modify files for addition
of rtl8723ae", and is d ue to a missing dependence of RTLWIFI on RTL8723AE.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We do not correctly change interface type when switching from
IBSS mode to STA mode, that results in microcode errors.

Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=886946Reported-by: NJaroslav Skarvada <jskarvad@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mesh PERR action frames are robust and thus may be encrypted, so add
proper head/tailroom to allow this.  Fixes this warning when operating
a Mesh STA on ath5k:

WARNING: at net/mac80211/wpa.c:427 ccmp_encrypt_skb.isra.5+0x7b/0x1a0 [mac80211]()
Call Trace:
 [<c011c5e7>] warn_slowpath_common+0x63/0x78
 [<c011c60b>] warn_slowpath_null+0xf/0x13
 [<e090621d>] ccmp_encrypt_skb.isra.5+0x7b/0x1a0 [mac80211]
 [<e090685c>] ieee80211_crypto_ccmp_encrypt+0x1f/0x37 [mac80211]
 [<e0917113>] invoke_tx_handlers+0xcad/0x10bd [mac80211]
 [<e0917665>] ieee80211_tx+0x87/0xb3 [mac80211]
 [<e0918932>] ieee80211_tx_pending+0xcc/0x170 [mac80211]
 [<c0121c43>] tasklet_action+0x3e/0x65
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

A user reported warnings in ath5k due to transmitting frames with no
rates set up.  The frames were Mesh PERR frames, and some debugging
showed an empty control block with just the vif pointer:

>  [  562.522682] XXX txinfo: 00000000: 00 00 00 00 00 00 00 00 00 00 00
>  00 00 00 00 00  ................
>  [  562.522688] XXX txinfo: 00000010: 00 00 00 00 00 00 00 00 54 b8 f2
>  db 00 00 00 00  ........T.......
>  [  562.522693] XXX txinfo: 00000020: 00 00 00 00 00 00 00 00 00 00 00
>  00 00 00 00 00  ................

Set the IEEE80211_TX_INTFL_NEED_TXPROCESSING flag to ensure that
rate control gets run before the frame is sent.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Channel contexts are not always used with monitor interfaces. If no channel
context is set, use the oper channel, otherwise tx fails.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
[check local->use_chanctx]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since:

commit b23b025f
Author: Ben Greear <greearb@candelatech.com>
Date:   Fri Feb 4 11:54:17 2011 -0800

    mac80211: Optimize scans on current operating channel.

we do not disable PS while going back to operational channel (on
ieee80211_scan_state_suspend) and deffer that until scan finish.
But since we are allowed to send frames, we can send a frame to AP
without PM bit set, so disable PS on AP side. Then when we switch
to off-channel (in ieee80211_scan_state_resume) we do not enable PS.
Hence we are off-channel with PS disabled, frames are not buffered
by AP.

To fix remove offchannel_ps_disable argument and always enable PS when
going off-channel and disable it when going on-channel, like it was
before.

Cc: stable@vger.kernel.org # 2.6.39+
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Tested-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

During FT roaming, wpa_supplicant attempts to set the
key before association. This used to be rejected, but
as a side effect of my commit 66e67e41
("mac80211: redesign auth/assoc") the key was accepted
causing hardware crypto to not be used for it as the
station isn't added to the driver yet.

It would be possible to accept the key and then add it
to the driver when the station has been added. However,
this may run into issues with drivers using the state-
based station adding if they accept the key only after
association like it used to be.

For now, revert to the behaviour from before the auth
and assoc change.

Cc: stable@vger.kernel.org
Reported-by: NCédric Debarge <cedric.debarge@acksys.fr>
Tested-by: NCédric Debarge <cedric.debarge@acksys.fr>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The rate scaling won't treat the information in a frame
with IEEE80211_TX_CTL_AMPDU set if IEEE80211_TX_STAT_AMPDU
is cleared. But all the frames coming from an AGG tx queue
have IEEE80211_TX_CTL_AMPDU set, and IEEE80211_TX_STAT_AMPDU
is set only if the frame was sent in an AMPDU.
This means that all the data in frames in AGG tx queues that
aren't sent as an AMPDU is thrown away.
This is even more harmful when in bad link conditions, the
frames are sent in an AMPDU and then finally sent as single
frame. So a lot of failures weren't reported and the rate
scaling got stuck in high rates leading to very poor
connectivity.

Fix that by clearing IEEE80211_TX_CTL_AMPDU when the frame
isn't part of an AMPDU.

This bug was introduced by

2eb81a40
iwlwifi: don't clear CTL_AMPDU on frame status

This fix basically reverts the aforementioned commit.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Fixes a reported CPU soft lockup where the tasklet tries to acquire the
lock and blocks while ath_prepare_reset (holding the lock) waits for it
to complete.

Cc: stable@vger.kernel.org
Reported-by: NRobert Shade <robert.shade@gmail.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: fix rx flush handling" added a deadlock that happens
because ath_rx_tasklet is called in a section that has already taken the
rx buffer lock.

It seems that the only purpose of the rxbuflock was a band-aid fix to the
reset vs rx tasklet race, which has been properly fixed in the commit
"ath9k: add a better fix for the rx tasklet vs rx flush race".

Now that the fix is in, we can safely remove the lock to avoid such issues.

Cc: stable@vger.kernel.org
Reported-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.

Cc: stable@vger.kernel.org
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Right now the rx flush is not doing anything useful on AR9003+, as it only
works if the buffers in the rx FIFO have not been purged yet, as is done
by ath_stoprecv.

To fix this, always call ath_flushrecv from within ath_stoprecv before
the FIFO is emptied, but still after the hw receive path has been stopped.

This ensures that frames received (and ACKed by the hardware) shortly before
a reset will be seen by the software, which should improve A-MPDU session
stability.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ensure that the rx tasklet is no longer running when entering the reset path.
Also remove the distinction between flush and no-flush frame processing.
If a frame has been received and ACKed by the hardware, the stack needs to see
it, so that the BA receive window does not go out of sync.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During teardown, mac80211 will not return a new beacon. This is normal and
handled properly in the driver, so there's no need to spam the user with a kernel
warning here.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the next beacon is sent, the ath_buf from the previous run is reused.
If getting a new beacon from mac80211 fails, bf->bf_mpdu is not reset, yet
the skb is freed, leading to a double-free on the next beacon tx attempt,
resulting in a system crash.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On AR9300 the rx FIFO needs to be empty during reset to ensure that no
further DMA activity is generated, otherwise it might lead to memory
corruption issues.

Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SKBs that are allocated in the HTC layer do not have callbacks
registered and hence ended up not being freed, Fix this by freeing
them properly in the TX completion routine.

Cc: <stable@vger.kernel.org>
Reported-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BAND_G is implicit when BAND_GN is present.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently "adapter->config_bands" is updated during infra
association only if channel is provided by user in "iw connect"
command. config_bands is used while preparing association
request to calculate supported rates by intersecting our rates
with the rates advertised by AP.

There is corner case in which we include zero rates in
supported rates TLV based on previous IBSS network history,
which leads to association failure.

This patch fixes the problem by correctly updating config_bands.

Cc: "3.7.y" <stable@vger.kernel.org>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Checking only for sco_conn seems to not be enough and lead to NULL
dereferences in the code, check for hcon instead.

<1>[11340.226404] BUG: unable to handle kernel NULL pointer dereference at
0000000
8
<4>[11340.226619] EIP is at __sco_sock_close+0xe8/0x1a0
<4>[11340.226629] EAX: f063a740 EBX: 00000000 ECX: f58f4544 EDX: 00000000
<4>[11340.226640] ESI: dec83e00 EDI: 5f9a081f EBP: e0fdff38 ESP: e0fdff1c
<0>[11340.226674] Stack:
<4>[11340.226682]  c184db87 c1251028 dec83e00 e0fdff38 c1754aef dec83e00
00000000
e0fdff5c
<4>[11340.226718]  c184f587 e0fdff64 e0fdff68 5f9a081f e0fdff5c c1751852
d7813800
62262f10
<4>[11340.226752]  e0fdff70 c1753c00 00000000 00000001 0000000d e0fdffac
c175425c
00000041
<0>[11340.226793] Call Trace:
<4>[11340.226813]  [<c184db87>] ? sco_sock_clear_timer+0x27/0x60
<4>[11340.226831]  [<c1251028>] ? local_bh_enable+0x68/0xd0
<4>[11340.226846]  [<c1754aef>] ? lock_sock_nested+0x4f/0x60
<4>[11340.226862]  [<c184f587>] sco_sock_shutdown+0x67/0xb0
<4>[11340.226879]  [<c1751852>] ? sockfd_lookup_light+0x22/0x80
<4>[11340.226897]  [<c1753c00>] sys_shutdown+0x30/0x60
<4>[11340.226912]  [<c175425c>] sys_socketcall+0x1dc/0x2a0
<4>[11340.226929]  [<c149ba78>] ? trace_hardirqs_on_thunk+0xc/0x10
<4>[11340.226944]  [<c18860f1>] syscall_call+0x7/0xb
<4>[11340.226960]  [<c1880000>] ? restore_cur+0x5e/0xd7
<0>[11340.226969] Code: <f0> ff 4b 08 0f 94 c0 84 c0 74 20 80 7b 19 01 74
2f b8 0a 00 00
Reported-by: NChuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

If remote device sends l2cap info request before read_remote_ext_feature
completes then mgmt_connected will be sent in hci_acldata_packet() and
remote name request wont be sent and eventually authentication wont happen

Hcidump log of the issue

< HCI Command: Create Connection (0x01|0x0005) plen 13
    bdaddr BC:85:1F:74:7F:29 ptype 0xcc18 rswitch 0x01 clkoffset 0x4bf7 (valid)
    Packet type: DM1 DM3 DM5 DH1 DH3 DH5
> HCI Event: Command Status (0x0f) plen 4
    Create Connection (0x01|0x0005) status 0x00 ncmd 1
> HCI Event: Connect Complete (0x03) plen 11
    status 0x00 handle 12 bdaddr BC:85:1F:74:7F:29 type ACL encrypt 0x00
< HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
    handle 12
> HCI Event: Command Status (0x0f) plen 4
    Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 1
> HCI Event: Read Remote Supported Features (0x0b) plen 11
    status 0x00 handle 12
    Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
> HCI Event: Max Slots Change (0x1b) plen 3
    handle 12 slots 5
< HCI Command: Read Remote Extended Features (0x01|0x001c) plen 3
    handle 12 page 1
> HCI Event: Command Status (0x0f) plen 4
    Read Remote Extended Features (0x01|0x001c) status 0x00 ncmd 1
> ACL data: handle 12 flags 0x02 dlen 10
    L2CAP(s): Info req: type 2
< ACL data: handle 12 flags 0x00 dlen 16
    L2CAP(s): Info rsp: type 2 result 0
      Extended feature mask 0x00b8
        Enhanced Retransmission mode
        Streaming mode
        FCS Option
        Fixed Channels
> HCI Event: Read Remote Extended Features (0x23) plen 13
    status 0x00 handle 12 page 1 max 1
    Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> ACL data: handle 12 flags 0x02 dlen 10
    L2CAP(s): Info req: type 3
< ACL data: handle 12 flags 0x00 dlen 20
    L2CAP(s): Info rsp: type 3 result 0
      Fixed channel list 0x00000002
        L2CAP Signalling Channel
> HCI Event: Number of Completed Packets (0x13) plen 5
    handle 12 packets 2

This patch moves sending mgmt_connected from hci_acldata_packet() to
l2cap_connect_req() since this code is to handle the scenario remote
device sends l2cap connect req too fast
Signed-off-by: NJaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Output of /sys/kernel/debug/usb/devices
T:  Bus=03 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  6 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3008 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NSergio Cambra <sergio@programatica.es>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

The length parameter should be sizeof(req->name) - 1 because there is no
guarantee that string provided by userspace will contain the trailing
'\0'.

Can be easily reproduced by manually setting req->name to 128 non-zero
bytes prior to ioctl(HIDPCONNADD) and checking the device name setup on
input subsystem:

$ cat /sys/devices/pnp0/00\:04/tty/ttyS0/hci0/hci0\:1/input8/name
AAAAAA[...]AAAAAAAAf0:af:f0:af:f0:af

("f0:af:f0:af:f0:af" is the device bluetooth address, taken from "phys"
field in struct hid_device due to overflow.)

Cc: stable@vger.kernel.org
Signed-off-by: NAnderson Lizardo <anderson.lizardo@openbossa.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Add support for the AR9462 chip

T: Bus=01 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e056 Rev=00.01
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Add support for the AR9462 chip

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e04e Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

T:  Bus=02 Lev=02 Prnt=02 Port=06 Cnt=01 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3006 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NDaniel Schaal <farbing@web.de>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>